Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Practical compensation for nonlinear dynamic thrust measurement system

The real dynamic thrust measurement system usually tends to be nonlinear due to the complex characteristics of the rig, pipes connection, etc. For a real dynamic measuring system,the nonlinearity must be eliminated by some adequate methods. In this paper, a nonlinear model of dynamic thrust measurement system is established by using radial basis function neural network(RBF-NN), where a novel multi-step force generator is designed to stimulate the nonlinearity of the system, and a practical compensation method for the measurement system using left inverse model is proposed. Left inverse model can be considered as a perfect dynamic compensation of the dynamic thrust measurement system, and in practice, it can be approximated by RBF-NN based on least mean square(LMS) algorithms. Different weights are set for producing the multi-step force, which is the ideal input signal of the nonlinear dynamic thrust measurement system. The validity of the compensation method depends on the engine’s performance and the tolerance error0.5%, which is commonly demanded in engineering. Results from simulations and experiments show that the practical compensation using left inverse model based on RBF-NN in dynamic thrust measuring system can yield high tracking accuracy than the conventional methods.     

大型枢纽机场中转水平评估研究

为了有效评估我国枢纽机场的中转水平,全面掌握枢纽机场发展中所面临的问题,构建了大型枢纽中转水平评估模型,并以中美欧三个国家和地区典型的大型枢纽为例进行实证分析。研究表明,与美国和欧洲大型枢纽的中转水平相比,我国大型枢纽的中转水平仍有很大差距;我国国内中转航班的中转水平远远低于美国,国内国际互转航班的中转水平与美国相当,国际转国际航班的中转水平高于美国;与欧洲三大国际枢纽的中转水平相比,我国北京首都机场与国际相关的水平中转仍有所不足。     

基于结构动力学特性的损伤识别方法

基于等效模态应变/动能理论,提出了一种利用实际结构的测试数据识别结构中损伤位置的方法。在此基础上,研究了利用模型修正技术识别结构中损伤强度的方法。分别以一个单损伤平板结构和多损伤平板结构为例,通过仿真分析了以上方法的有效性。结果表明,以上方法可以有效识别结构中的损伤位置和损伤强度。     

大型齿轮在多因素耦合影响下齿形误差测量的灰色动态预报

提出了一种旁置式的大型齿轮测量装置,分析了影响该装置测量精度的主要误差来源及其特性,给出了一种处理多因素耦合影响的灰色动态预报方法.首先,基于测量装置特性,对影响齿形误差测量精度的误差源进行分析和标定,计算出各误差源的灵敏度系数;然后对测得的有限误差数据进行再抽样及灰色生成,分别计算出在每次测量中各影响因素对测量结果的作用大小,之后按照误差合成方法生成误差源耦合作用结果;最后,通过在测量结果中去除耦合作用进而提高大型齿轮齿形误差测量精度.与测量精度为0.5μm的三坐标测量机进行对比测量,结果表明所提出测量装置能满足3级精度以上的大型齿轮齿形误差检测需求.     

LIPS-200离子推力器放电室原初电子动力学行为的数值模拟研究

为了得到试验测量不到的气体放电过程中电磁场作用下单个原初电子的动力学行为,建立了LIPS-200离子推力器放电室二维仿真模型,应用网格粒子法(PIC)和蒙特卡洛碰撞(MCC)模拟法对其进行了研究。模拟得到在额定工况下原初电子和中性原子之间的碰撞概率、原初电子损耗率、电磁场分布对其运动速度及运动轨迹的影响等。结果表明磁铁表面磁感强度最大,越靠近放电室内部磁感强度越小,对称轴区域无磁场分布,原初电子在电磁场作用下沿磁力线作加速螺旋运动;运动等离子体的自洽电势大小范围仅为0~2.0V,几乎不会影响等离子体运动;对应总原初电子个数为1.2×106时直接被阳极表面吸收的损耗率仅为0.02%。     

乙醇-空气稀液雾值班火焰的大涡模拟研究

为加深对气液两相湍流燃烧现象的认知,检测火焰面模型在液雾燃烧中的适用性,本文在欧拉-拉格朗日架构下使用火焰面/反应进度变量模型(FPV)数值模拟了乙醇-空气稀液雾值班火焰。欧拉坐标系下的气相湍流场使用大涡模拟方法模拟,离散液相则使用拉格朗日颗粒轨道模型进行描述,考虑了相间质量、动量、能量交换。燃烧模型中采用碳元素定义混合物分数,在混合物分数方程源项中体现液相对燃烧模型的影响。模拟得到的气相温度分布和液相统计值均和实验数据较好吻合,验证了该燃烧模型对稀液雾扩散类型火焰的适用性。分析瞬时图发现,该稀液雾火焰的最高燃烧温度往往位于当量混合物分数附近,在出口下游20倍直径处火焰完全点着,此处上游FPV模型能给出局部点火熄火现象。蒸发作用在剪切层和点火区域较强,而液滴和火焰作用较弱,单一液滴很少被火焰包围。     

2.5维机织复杂结构件的静强度

采用宏细观结合方法,针对经纱和纬纱等材料组分可能发生的多种失效模式,分别建立了基于改进的Hashin准则的系统性的材料失效准则及不同失效模式下的刚度退化模型.引入逐渐损伤的思想,建立了2.5维机织复杂结构件静强度系统性分析方法.模拟并分析了材料经向拉伸和纬向拉伸的应力-应变曲线,与实验得到的材料应力-应变曲线相比,相同应变下应力误差不超过6.5%,具有较好的重合度;对2.5维机织压气机静子连接结构模拟件开展了逐渐损伤模拟,结果表明:结构损伤主要集中在叶根倒角附近,其中吸力面叶根处的基体压缩失效形式会引起结构大幅变形,是结构破坏的主要原因.      

基于EFFD方法的自然层流短舱优化设计

采用extended free-form deformation(EFFD)方法研究了自然层流(natural laminar flow,NLF)短舱的气动外形优化设计方法.使用基于Bernstein基函数的EFFD方法完成了NLF短舱剖面的参数化,利用基于k-εSST(shear stress transport)两方程湍流模型的γ-θ转捩模型进行自然转捩预测,结合EFFD、一种混合动网格方法、Kriging代理模型和改进的粒子群算法(particle swarm optimization,PSO)建立了针对NLF短舱气动外形的优化设计框架.采用该框架分别对通气NLF短舱和带动力NLF短舱进行优化设计.单独通气NLF短舱优化结果的外表面实现48%的层流,阻力系数比初始通气NLF短舱减小了0.0003.带动力NLF短舱的优化结果外表面保持了41%的层流.这些结果表明采用相关技术建立的优化设计框架在NLF短舱设计中具有一定应用价值.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.