Neck-spinning quality analysis and optimization of process parameters for plunger components: Simulation and experimental study

The plunger component is a key part of the plunger pump in the aircraft hydraulic system. Neck-spinning process is commonly used to fabricate plunger components, of which the quality of the spinning process significantly affects the performance of plunger pumps. One of the bottlenecks faced by the industry in the spinning process is to choose a suitable neck-spinning process so as to ensure the quality of plunger components. It is necessary to propose a reliable method to optimize the process parameters which affect the neck-spinning quality of plunger components. In this study, a calculable finite element analysis (FEA) model is established to simulate the three-roller neck-spinning process of the plunger component, which includes six typical slipper structures, two roller structures, and two spinning parameters. The FEA model is then validated by comparing the simulated spinning forces with the corresponding experimental results. The influence of the process conditions on the neck-spinning quality is investigated. And the orthogonal simulation results are analyzed by a combination of range method and fuzzy mathematical analysis method to recommend a reasonable slipper structure, roller structure and neck-spinning parameters. This study provides a promising method to improve the manufacturing quality of the typical plunger components.     

ADS-B统计数据的位置导航不确定类别质量分析

为实现广播式自动相关监视(ADS-B)航迹与雷达航迹的高质量融合,必须对ADS-B航迹和雷达航迹数据质量进行分析。在分析实际ADS-B航迹数据的基础上,提出以航路为参考基准验证ADS-B航迹数据精度及完好性的方法。根据ADS-B报文中的位置导航不确定类别(NUCp)值,统计航迹点与航路中心线的水平偏差并将其作为位置实际误差,运用分位数-分位数图法对位置实际误差进行正态分布检验,得出置信水平为99%的实际误差置信区间,即在不同NUCp值下可信赖的位置误差范围。实验结果表明,在采用加权平均法进行航迹融合时,与传统权重分配相比,对于NUCp值为5或6的ADS-B航迹数据可增大权重,而对于NUCp值为7的数据则应减小权重。     

SE(3)上航天器姿轨耦合固定时间容错控制

针对相对运动航天器姿轨一体化控制问题,考虑执行器故障和控制输入饱和的影响,提出了一种基于滑模的模糊自适应固定时间容错控制方法。首先,在李群SE（3）的框架下建立并推导相对运动航天器姿轨一体化误差动力学模型;其次,引入执行器故障和控制输入饱和的问题,采用双幂次快速终端滑模面,并结合模糊自适应方法设计了固定时间稳定的容错控制器,可以实现执行器故障情况下相对运动航天器的高精度快速跟踪控制;然后,运用Lyapunov方法证明了系统的稳定性,该控制器不仅能不依赖于系统的初始状态实现滑模趋近和到达阶段的固定时间稳定性,而且由于采用模糊逼近方法结合自适应更新策略可以实时高精度地估计系统的总扰动信息,因此可以达到快速高精度的容错控制目标;最后,对所提出的的控制方法进行数值仿真分析,结果验证了该方法的有效性和可行性。     

对空间碎片的相对位姿估计

针对几何、质量特性参数均未知的空间碎片,提出一种基于扩展卡尔曼滤波（EKF）的相对位姿估计算法。该算法以单目相机获得的目标图像特征视线信息作为测量输入,以目标姿态、姿态角速度、惯量比、相对位置、相对速度和特征位置作为滤波状态。对算法进行可观性分析,给出两个可以保证算法可观性的条件。分别针对不同条件进行数值仿真,仿真结果表明新算法能够对几何和质量参数未知的空间碎片进行有效的相对位姿 估计。     

Milling surface roughness for 7050 aluminum alloy cavity influenced by nozzle position of nanofluid minimum quantity lubrication

In nanofluid minimum quantity lubrication (NMQL) milling of aviation aluminum alloy, it is the bottleneck problem to adjust the position parameters (target distance, incidence angle, and elevation angle) of the nozzle to improve the surface roughness of milling, which has large and uncontrollable errors. In this paper, the influence law of milling cutter speed, helical angle, and cavity shape on the flow field around the milling cutter was studied, and the optimal nozzle profile parameters were obtained. Using 7050 aluminum alloy as the workpiece material, the milling experiment of the NMQL cavity was conducted by utilizing cottonseed oil-based Al₂O₃ nanofluid. Results show that the high velocity of the surrounding air flow field and the strong gas barrier could be attributed to high rotating velocities of the milling cutter. The incidence angle of the nozzle was consistent with the helical angle of the milling cutter, the target distance was appropriate at 25–30 mm, and the elevation angle was suitable at 60°–65°. The range and variance analyses of the signal-to-noise ratio of milling force and roughness were performed, and the chip morphology was observed and analyzed. The results show that the optimal combination of nozzle position parameters was the target distance of 30 mm, the incidence angle of 35°, and the elevation angle of 60°. Among these parameters, target distance had the largest impact on cutting performance with a contribution rate of more than 55%, followed by incidence angle and elevation contribution rate. Analysis by orthogonal experiment revealed that the nozzle position parameters were appropriate, and R_a (0.087 μm) was reduced by 30.4% from the maximum value (0.125 μm). Moreover, R_sm (0.05 mm) was minimum, which was 36% lower than that of the seventh group (R_sm = 0.078 mm).     

无人侦察机航迹点重规划的优化算法

提出了一种针对发现新目标后,机上在线进行航迹点重规划的方法.建立了重规划数学模型,用图像质量方程预估侦察目标的图像质量,以所有目标图像质量的加权之和最大、路径长度最小为目标函数.在传感器侦察范围、飞机机动和目标图像质量要求以及威胁等多约束条件下运用改进后的多目标进化算法NSGA-II寻优,得到侦察航迹点的Pareto最优解集.以目标图像质量、路径长度和路径威胁为评价因素,专家系统给出当前评价因素加权权值,用模糊选优方法在Pareto最优解集中选择该加权意义下的唯一最优路径.仿真结果证明了该方法的可行性和智能性.     

浸种剂和灌溉对芽期人工低温下直播水稻幼苗质量的影响

在人工气候室内模拟早春"倒春寒"气候特点,研究了"齐苗快"和灌溉对芽期人工低温下直播水稻幼苗质量的影响.结果表明,"齐苗快"浸种结合湿润灌溉有利于提高芽期低温后精量穴直播水稻的幼苗质量.与清水浸种相比,"齐苗快"浸种处理能显著降低湘早籼24号和株两优2号的株高和叶片质膜透性,提高2种水稻品种的叶龄、茎基宽、苗高干质量、总根体积、顶1叶SPAD值;与淹水灌溉相比,湿润灌溉能显著提高2种水稻品种的成苗率,并降低其质膜透性.     

项目组织管理能力不足造成的项目成本损失分析

文章旨在描述一种对项目组织管理能力不足造成的成本损失进行分析的思路和方法。在项目管理中,通过对“项目组织管理成本损失因子”的分析和有效管理,实现对项目组织管理能力的综合量化评价提供参考依据。     

一种新的红外目标图像质量评价方法

 目标混淆度（DTC）和目标遮隐度（DTS）是两个有效的红外小目标图像质量评价指标,然而它们不能够评价大目标图像的质量。针对该问题,对两个指标的定义进行了拓展,实现了对红外小目标图像质量和红外大目标图像质量的统一描述。对于小目标图像,修正了两个指标原有的计算方法,分别体现了背景噪声引入虚警的能力和背景区域遮隐目标的能力;对于大目标图像,提出了该图像条件下两个指标的计算方法,分别体现了背景区域与目标区域的相似程度以及图像中目标信息与已知信息相比偏离的程度。理论分析和实验证明,与传统的图像质量评价标准如信噪比、杂波尺度等相比,本文方法在红外自动目标识别中的应用更为有效,其评价结果与实际情况更加吻合。