三维网络碳化硅多孔陶瓷的制备

以中间相沥青添加55%(质量分数,下同)的Si粉混合物为原料,制备了含Si的炭泡沫模板。在高温反应烧结炉中,氩气气氛下1500℃保温1～6h,结合反应烧结工艺制备了碳化硅多孔陶瓷。利用扫描电子显微镜(SEM)和X射线衍射分析仪(XRD)对碳化硅多孔陶瓷的微观形貌、物相组成进行了观察,并对熔融Si与C的反应机理进行了探讨。结果表明:碳化硅多孔陶瓷的微观结构与炭泡沫模板的微观结构一致,烧结温度1500℃下,随着保温时间的延长,多孔陶瓷的弯曲强度先增大后减小,而孔隙率先减小后增大;在保温4h的条件下制备的碳化硅多孔陶瓷主要由β-SiC相组成,最大弯曲强度为26.2MPa,对应的孔隙率为45%。内部熔融的Si与外部熔融的Si同时与C反应生成SiC,最后两者结合在一起形成致密的SiC多孔陶瓷。     

混合法(权函数─—光测技术)在断裂力学中的应用研究

本文采用作者提出的混合法（将光测技术与权函数相结合）,求解了含孔板在不同应力场裂纹的应力强度因子。     

统一强度理论下受特殊荷载的简支圆板极限荷载统一解

对于线性和均布荷载共同作用下的简支圆板,本文采用统一强度理论对其进行了塑性极限分析。考虑了两种作用形式,分别得出了统一解。利用该解可得出一系列不同屈服准则下的解析解和极限荷载随不同屈服准则的变化曲线。在统一强度理论中,不同的b值得到不同的屈服准则,对应不同的工程材料,其中α可根据实际的工程材料拉压强度比确定。当α≠1时,统一强度理论适用于拉压强度相同的材料,当α≠1时,适用于拉压强度不同的材料。已有的Mises解是本文解的特例,从文中的统一解得知,正确认识材料强度并合理运用屈服准则对发挥材料潜能具有重要意义。     

密度变化时金属橡胶材料的非线性本构关系

以多孔材料理论为基础,干摩擦非线性理论为依据,并结合小曲梁模型建立金属橡胶材料的非线性本构关系,对空心圆柱形金属橡胶材料的静态试验结果进行拟合,得到非线性本构关系模型中的各项系数与密度的变化关系式,从而实现对该材料在密度发生变化情况下的本构关系的预估。     

预烧结对反应烧结多孔氮化硅陶瓷性能的影响

研究了预烧结对反应烧结多孔氮化硅陶瓷的介电性能和力学性能的影响。通过添加30wt%的成孔剂颗粒,制备出孔隙率在55%左右的具有宏观球形孔的多孔氮化硅陶瓷。反应烧结前,在低于硅熔点的温度下,对多孔硅坯体进行不同温度和不同时间的预烧。结果表明,随着预烧结温度的增高和时间的加长,反应烧结后烧结体的强度明显提高,介电常数ε′和介电损耗tanδ都有小幅度的增加。在硅粉中添加5wt%Y2O3 5wt%Al2O3进行预烧,可以减小反应烧结后试样的ε′,并且随预烧结时间的增加而减小。     

Integrated design of topology and material for composite morphing trailing edge based compliant mechanism

The morphing trailing edge based compliant mechanism is a developing technology which can increase lift-drag ratio for variable flight modes by bending down the trailing edge. Composite material design is integrated into topology optimization for the morphing trailing edge based compliant mechanism in the paper. A two-step optimization strategy is established to solve the integrated design problem. Initially, lamination parameters are introduced and viewed as a bridge between structure stiffness and fiber angles for composite material. Design variables include the lamination parameters and element density. The least-squares between actual and desired displacements at output points along trailing edge is adopted to evaluate the deformed capability of the trailing edge. An integrated optimization model for the composite morphing trailing edge is established with the volume constraints. The optimal topologic shape and lamination parameters are initially obtained. Subsequently, a least-squares optimization between fiber angles and the optimal lamination parameters is implemented to obtain optimal fiber angles. Finally, morphing capability of composites trailing edge based compliant mechanism is investigated by simulation and experiments. The results indicate the composites trailing edge based compliant mechanism can approximately bend down 8 degrees and satisfies the design requirement.     

Static Analysis of Functionally Graded Sandwich Plates Using an Efficient and Simple Refined Theory

In this paper, a new displacement based high-order shear deformation theory is introduced for the static response of function-ally graded sandwich plate. Unlike any other theory, the number of unknown functions involved is only four, as against five in case of other shear deformation theories. The theory presented is variationally consistent, has strong similarity with classical plate theory in many aspects, does not require shear correction factor, and gives rise to transverse shear stress variation such that the transverse shear stresses vary parabolically across the thickness satisfying shear stress free surface conditions. Two common types of functionally graded sandwich plates, namely, the sandwich with functionally graded facesheet and homogeneous core and the sandwich with homogeneous facesheet and functionally graded core, are considered. Governing equations are derived from the principle of virtual displacements. The closed-form solution of a simply supported rectangular plate subjected to sinu-soidal loading has been obtained by using the Navier method. The validity of the present theory is investigated by comparing some of the present results with those of the classical, the first-order and the other higher-order theories. It can be concluded that the proposed theory is accurate and simple in solving the static bending behavior of functionally graded sandwich plates.     

环板在边缘弯矩和局部均布、线性荷载共同作用下的塑性极限分析(Ⅰ)

应用奇异函数求出环板在边缘弯矩和局部均布、线性分布荷载共同作用下的极限荷载的计算公式，并可画出极限荷载的影响曲线。     

SPECIAL HIGH-ORDER BENDING CRACK TIP FINITE ELEMENT FOR THE REISSNER PLATE

ＳＰＥＣＩＡＬＨＩＧＨ┐ＯＲＤＥＲＢＥＮＤＩＮＧＣＲＡＣＫＴＩＰＦＩＮＩＴＥＥＬＥＭＥＮＴＦＯＲＴＨＥＲＥＩＳＳＮＥＲＰＬＡＴＥＪｉａｎｇＣｈｉｐｉｎｇ（ＤｅｐａｒｔｍｅｎｔｏｆＦｌｉｇｈｔＶｅｈｉｃｌｅＤｅｓｉｇｎａｎｄＡｐｐｌｉｅｄＭｅｃｈａｎｉ...     

轴向运动粘弹性板横向振动分析的有限差分方法

研究轴向运动粘弹性矩形薄板的横向振动特性.根据牛顿第二定律建立了偏微分控制方程,采用有限差分法,计算四边简支边界条件下粘弹性板的无量纲固有复频率.重点讨论了矩形薄板的粘弹性系数、轴向无量纲运动速度对其横向振动特性的影响.