运动单站干涉仪相位差直接定位方法

针对传统干涉仪测向定位在低信噪比(SNR)下性能降低、多频段系统复杂等缺点,本文直接利用运动单站干涉仪模糊相位差(PD)实现对地面静止辐射源定位.为解决该定位问题,结合干涉仪相位差的几何特性,提出了一种多角度距离参数化高斯和滤波(MB-RP-GMF)定位解算方法,利用相位差误差检测获得多个初始方位角,通过距离参数化得到一组滤波初始值,采用扩展卡尔曼滤波(EKF)进行定位计算.仿真结果表明,该定位方法在低信噪比下优于仅测向(BO)定位,且仅采用一组干涉仪便可对多个频段辐射源进行定位.     

一种尾流消散动态预测的改进算法

尾流间隔是增大跑道容量的主要限制因素之一，为了在保持安全水平的前提下有效地增大跑道容量，可以对尾流消散进行动态预测，并据此缩减尾流间隔。研究了一种尾涡消散动态预测算法，该算法考虑了真实大气的大气分层、湍流、侧风、迎面风、风切变以及地效影响，并用一阶后向差分对该算法进行了离散化改进；在改进算法的基础上，时进近阶段尾流的消散在Matlab中进行了仿真计算；计算结果复现了尾涡的下沉现象和侧风对尾涡传输的线性累积效应。     

一种高效的基于可靠性的多学科设计优化方法(英文)

Design for modem engineering system is becoming multidisciplinary and incorporates practical uncertainties; therefore, it is necessary to synthesize reliability analysis and the multidisciplinary design optimization （MDO） techniques for the design of complex engineering system. An advanced first order second moment method-based concurrent subspace optimization approach is proposed based on the comparison and analysis of the existing multidisciplinary optimization techniques and the reliability analysis methods. It is seen through a canard configuration optimization for a three-surface transport that the proposed method is computationally efficient and practical with the least modification to the current deterministic optimization process.     

时差定位卫星簇的时域关联干扰方法研究

时差定位卫星簇对地表的辐射源存在很大威胁.为保护目标辐射源,在分析时差定位卫星簇TDOA脉冲配对的原理的基础上,提出一种新的主动干扰方法.即通过控制干扰脉冲与辐射源脉冲之间的时域关联关系,达到欺骗时差定位卫星的TDOA估计.仿真计算表明,适当的脉冲发射时间和脉冲宽度的同频干扰源对辐射源位置信息的保护具有可行性和有效性.     

A closed-form solution for moving source localization using LBI changing rate of phase difference only

Due to the deficiencies in the conventional multiple-receiver localization systems based on direction of arrival(DOA) such as system complexity of interferometer or array and amplitude/phase unbalance between multiple receiving channels and constraint on antenna configuration,a new radiated source localization method using the changing rate of phase difference(CRPD)measured by a long baseline interferometer(LBI) only is studied. To solve the strictly nonlinear problem, a two-stage closed-form solution is proposed. In the first stage, the DOA and its changing rate are estimated from the CRPD of each observer by the pseudolinear least square(PLS) method,and then in the second stage, the source position and velocity are found by another PLS minimization. The bias of the algorithm caused by the correlation between the measurement matrix and the noise in the second stage is analyzed. To reduce this bias, an instrumental variable(IV) method is derived. A weighted IV estimator is given in order to reduce the estimation variance. The proposed method does not need any initial guess and the computation is small. The Cramer–Rao lower bound(CRLB) and mean square error(MSE) are also analyzed. Simulation results show that the proposed method can be close to the CRLB with moderate Gaussian measurement noise.     

快速拉格朗日差分法在巷道锚杆支护计算中的应用

快速拉格朗日法是一种新型的数值计算方法。本文介绍了快速拉格朗日法的基本原理和分析过程；并将这种方法应用于巷道锚杆支护的计算中，对锚杆支护前后围岩的变形进行了对比。结果表明锚杆在控制围岩垂直方向的变形有明显的作用。     

HS—19型肖氏硬度计故障分析

从结构原理来分析故障的产生、发展、现象以及产生故障的排除方法。     

R-PP改性沥青侧缠绕管道防腐作业线的研制与应用

本文着重介绍R-PP改性沥青侧缠绕管道防腐作业线的工作原理及研制过程。通过防腐实验，对作业线存在的若干技术问题进行了改进和调整，为作业线应用于管道防腐提供了必要的技术依据。     

民用飞机不同商载配置对机身着陆载荷的影响分析

重量分布和重心位置是影响起落架和机体地面载荷的重要因素,其中商载是影响全机重心、惯量的最活跃因素。飞机实际运营中,有无穷多种商载分布及装载方案。为了确保机身载荷分析时,不遗漏严重设计情况,同时能大大减少载荷人员的工作量,本文对不同商载配置下的机身着陆载荷进行了研究分析,分析结果表明最大商载情况将构成机身垂直剪力和垂直弯矩的严重情况。因此,在进行机身载荷分析时,必须考虑最大商载情况,而最大燃油情况可以不必考虑。这一结论为今后有针对性的开展民机机身载荷分析提供了数据支持。     

弹簧杆校正原理及其在力矩控制系统中的应用

 为了掌握自动飞行器的工作特性,在它飞上空中之前,工程技术人员要在地面进行各种仿真试验。研制力矩控制系统的目的在于模拟随高度、速度变化且连续作用在飞行器翼面上的气动铰链力矩。这种装置广泛应用于各种型号舵机。 我们研制的力矩控制系统力案如图1所示。