A closed-form solution for moving source localization using LBI changing rate of phase difference only

Due to the deficiencies in the conventional multiple-receiver localization systems based on direction of arrival(DOA) such as system complexity of interferometer or array and amplitude/phase unbalance between multiple receiving channels and constraint on antenna configuration,a new radiated source localization method using the changing rate of phase difference(CRPD)measured by a long baseline interferometer(LBI) only is studied. To solve the strictly nonlinear problem, a two-stage closed-form solution is proposed. In the first stage, the DOA and its changing rate are estimated from the CRPD of each observer by the pseudolinear least square(PLS) method,and then in the second stage, the source position and velocity are found by another PLS minimization. The bias of the algorithm caused by the correlation between the measurement matrix and the noise in the second stage is analyzed. To reduce this bias, an instrumental variable(IV) method is derived. A weighted IV estimator is given in order to reduce the estimation variance. The proposed method does not need any initial guess and the computation is small. The Cramer–Rao lower bound(CRLB) and mean square error(MSE) are also analyzed. Simulation results show that the proposed method can be close to the CRLB with moderate Gaussian measurement noise.     

含噪信号经验模式分解虚假分量识别方法

针对含噪信号Hilbert-Huang变换存在虚假分量,提出改进的奇异值分解(SVD)方法进行降噪,改进包含两个部分:一是利用重构相空间代替传统矩阵如Hankel矩阵,以去掉信号冗余,再者提出奇异值能量熵分量差分法,更易于定出重构奇异值阶次;二是提出了频谱比值法对虚假分量进行辨识,更有效辨识出虚假分量.首先利用经验模式分解(EMD)得到本征模式分量(IMF),识别并剔除趋势项,重构信号,然后进行SVD,重构降噪后的信号,消除虚假分量,最后进行时频分析.联合方法应用于含噪仿真信号,信噪比(signal noise ratio,SNR)提高了5.5%,虚假分量辨识率提高至100%,用于双跨转子故障振动信号,得到正确的时频结果,表明了所提方法识别含噪信号虚假分量的有效性.     

交会对接寻的段水平双脉冲交会轨道精确求解

基于考虑摄动影响的精确轨道动力学模型,对交会对接寻的段水平双脉冲交会轨道的精确求解方法进行了研究。提出了将控制脉冲的俯仰角近似转化为控制时刻的轨道幅角,从而调整脉冲控制时刻以消除径向速度增量的方法,精确求解首末水平双脉冲的启控时刻;引入导引终点位置偏差的比例控制方法,精确求解水平双脉冲的精确控制量。仿真结果表明,2轮整体迭代可获得首末水平脉冲控制时刻和控制量的精确值,脉冲水平特性达到俯仰角小于1°,导引终点相对位置精度达到10m,验证了该方法的正确性。     

飞机下滑波束导引系统设计及仿真

下滑波束导引系统是飞机在自动着陆时所采用的一种重要无线电波束导引系统。首先,简要阐述了下滑波束导引系统的基本工作原理;然后,对导引系统的运动学环节及下滑耦合器进行分析,对飞机下滑波束导引系统结构进行设计;最后,在MATLAB平台下,对所设计的下滑波束导引系统进行大量仿真研究。仿真结果显示。所设计的下滑波束导引系统结构是合理的,其控制系统是稳定的,且其稳态性能也得到改善。     

利用格壁安装角对栅格舵展开折叠压心控制的工程方法研究探索

随着技术的发展，在工程设计中，对于巡航迎角下栅格舵导弹的展开与折叠的压心变化控制对于控制系统来说尤为重要。本文创新性的首次提出利用栅格舵的内壁单元的偏转，即相对于水平面的夹角来实现在设计点下的压心控制。由于设计过程需要多次迭代，本文利用计算在所关注的设计点处对展开折叠压心进行了验证，创造性的利用了等效代替的方法提出了一种新型的计算折叠状态压心的快速工程方法。     

Assessing the feasibility of involving gaseous products resulting from physicochemical oxidation of human liquid and solid wastes in the cycling of a bio-technical life support system

The study addresses the possible ways of involving gaseous products produced by “wet” incineration of human wastes mixed with H₂O₂ in an alternating electric field in the cycling of the physical model of a bio-technical life support system (BTLSS). The resulting gas mixture contains CO₂ and O₂, which are easily involved in the cycling in the closed ecosystem, and NH₃, which is unacceptable in the atmosphere of the BTLSS. NH₃ fixation has been proposed, which is followed by nitrification and involvement of the resulting products in the mass exchange of the closed system. Experiments have been performed to show that plants can be grown in the atmosphere resulting from the closing of the gas loop that includes a physicochemical installation and a growth chamber with plants representing the phototrophic compartment of the BTLSS. The results of the study suggest the conclusion that the proposed method of organic waste oxidation can be a useful tool in creating a physical model of a closed-loop integrated BTLSS.     

歼×飞机攻角位置误差校准的试验研究

本文简述了目前歼×飞机的攻角位置校准的试验方法。通过分析比较 ,认为采用微波空间定位校准法进行攻角位置误差校准优于目前风洞试验校准法     

α、β相分布形态对TC11钛合金高温循环蠕变速率的影响

对TC1 1钛合金施行了不同的热处理制度 ,得到 3种组织形态 ,研究了不同的组织形态的高温循环蠕变。结果表明 ,晶间 β组织具有低的循环蠕变速率 ,而随最大应力的增加 ,蠕变速率增加快 ;而等轴组织和片状组织循环蠕变速率较高 ,但随应力的增加 ,蠕变速率增加较慢。分析认为 ,晶界滑移行为对高温循环蠕变有重要影响     

舰载飞机弹射起飞自动控制上升的飞行特性

根据舰载飞机弹射起飞上升段的纵向动力学方程和迎角自动控制的升降舵偏角调节规律，计算了Ａ－６飞机的迎角，俯仰角、飞机重心垂向位置等随时间的变化，确定了传递系数ｋｏ，ｋｉ的合适范围，讨论了以最大容许的下沉量作为约束的指令迎角的量值，提出了舵面偏角调节规律的一种设计方法。     

高分影像辅助下的航空高光谱严密几何检校方法

 惯性测量单元(IMU)与传感器视准轴的偏心角和偏心矢量是造成航空线阵列高光谱数据几何校正误差的主要原因之一。在分析偏心角与偏心矢量误差来源之后提出该误差由IMU主轴与传感器主轴的角度偏差、测区固定偏差、GPS中心与传感器投影中心相对偏差组成,在此基础上建立了较为严密的检校模型。针对模型解算时需要大量高精度控制点的问题,提出了一种高分影像辅助下的亚像元精度控制点自动提取方法。通过多地区、多传感器高光谱航测实验表明,亚像元精度控制点能有效提高模型解算精度。新检校模型可获得亚像元校正精度,推扫式传感器——应用型机载成像光谱仪(AISA)建模中误差约为0.39个像元,摆扫式传感器——实用型模块化成像光谱仪(OMIS)建模中误差约为0.23个像元,校正后的影像可直接进行拼接。