超声速流中激波/湍流附面层干扰数值模拟

采用修正的B／L湍流模型以及多块结构化网格求解了二维N-S方程。分别对超声速流和高超声速流中的激波／湍流附面层干扰进行了数值研究。本文首先研究了进口马赫数为2．96的超声速流。计算结果准确预测了入射斜激波在平直壁面引起湍流附面层分离的流动特征：分离点的反射激波、分离包引起的膨胀扇以及再附点的反射激波。计算的壁面压力分布与实验值吻合较好，计算的分离区长度与实验值比较有一定误差。本文还对进口马赫数为9．22的高超声速流中压缩角引起的激波／湍流附面层干扰进行了数值研究。计算结果与实验结果吻合较好。     

直接不交化方法在故障树定量分析中的应用

在布尔集合运算方法和不交化方法基础上，提出了单调关联故障树系统定量分析优化方法，通过故障树定量分析优化方法，可以方便地得到系统的可靠度、不可靠度、最小割集、最小路集、关键重要度等指标。     

悬臂空心梁式加速度计的设计

分析证明:悬臂梁式加速度计的灵敏度与它的谐振频率的平方成反比。因此,欲展宽频带而保持灵敏度不变就很困难。利用应力集中的方法可以有效地解决这一问题。采用空心梁结构不仅能产生应力集中而且能减少梁的自身质量带来的影响,可以有效地展宽频带。文中给出了几种梁的刚度计算。     

微重力场中对流—辐射—传质系统的地面模拟技术

研究了微重力条件下对流－辐射－传质稳态系统的地面相似模拟技术，进一步发 温度－材料综合保护技术。通过采取补偿热流，调整壁面热流密度分布的方法，保持了原型与尺寸适当缩小后的模型的Ｎｕ数，Ｓｈ数，材料，温度，湿度不变，从而实现模型与原型流动，换热和传质相似。     

基于连续覆盖特性分析的星座设计

研究了需要对地面目标进行连续覆盖的星座的设计问题．首先推导了对覆盖性能有重要影响的星间覆盖间隔时间和轨道面覆盖间隔时间的计算公式，通过算例针对不同配置的星座进行了计算，使用工程仿真软件STK验证了分析结果．通过理论分析、算例计算以及工程仿真为该类型星座设计提供了理论指导。     

喷管扩张段烧蚀的“台阶效应”计算

当喉衬和扩张段内衬采用具有不同烧蚀率的材料时,常出现“台阶效应”.本文以气动热化学烧蚀机理为基楚,提出应用适当的对流换热和加剧的化学反应计算对台阶效应区进行修正的方法,使台阶效应区的烧蚀率预示更切合实际工况.     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

A general calculation method to specify center-of-buoyancy for the stratospheric airship with multiple gas cells

As the lighter-than-air (LTA) flight vehicle, the stratospheric airship is a desirable platform to provide communication and surveillance services. During the ascent from sea-level to the mission altitude, the volume of the lifting gas may change significantly, which will result in the change of the center-of-buoyancy (CB). A general calculation method is developed to specify CB for the stratospheric airship with a double-ellipsoid hull and an arbitrary number of the gas cells. The cross-section-integral (CSI) method is used as a basic calculation scenario to specify CB. Considering the complexity in determining the boundary between the helium and air in the gas cell, a searching algorithm is put forward and the specification of CB can be conducted by the iterative calculation. As an important application, the stable condition of the pitch angle is analyzed when the change of CB is involved. Under different initial configurations, the stable pitch angle of the stratospheric airship during the ascent is specified and compared, which shows the advantages of the multi-gas-cell configuration. The results of this paper may provide an important reference for the engineering application of the stratospheric airship.     

静止轨道卫星通信链路的预算与分析

星地链路计算作为卫星通信的重要技术，是卫星通信系统设计的基础和理论依据，直接决定了卫星通信系统的链路通信质量。由于影响卫星链路的因素很多，设计中存在一处不合理即使得整条星地链路不可用，造成巨大的损失。而且在实际设计中无法做到最理想的链路状态，往往需要在某方面有所取舍，这也是链路计算中的一大难点。基于目前国际通用的链路计算方法，将星地链路上下行拆分，独立计算，综合分析，再结合实际工程经验，分析和计算实际工程案例，针对不同的链路配置给出相应合理的设计方法，可作为静止轨道通信卫星星地链路计算分析的参考。     

微分法在定位误差分析与计算中的应用

介绍了微分法分析计算定位误差的原理和适用范围,通过生产实例分析,证明了该方法在解决多误差因素定位误差分析与计算中的简便与快捷,从而有效简化了复杂定位方案定位误差的分析与计算,提高了夹具的设计效率。