基于快速平行因子分解的声矢量传感器阵二维DOA估计

将声矢量传感器阵列参数估计问题与平行因子(Parallel factor,PARAFAC)模型相结合,提出了一种基于快速PARAFAC分解的二维波达方向(Direction of arrival,DOA)估计算法。该算法首先将接收信号构建为PARAFAC模型,然后在数据域对参数矩阵进行初估计,最后利用PARAFAC分解获得信号二维DOA估计。该算法能够应用于任意结构的声矢量传感器阵列,同时能够得到和信源一一匹配的仰角和方位角估计。借助于参数矩阵的初始估计,所提算法收敛速度较快,其计算复杂度大大降低。该算法角度估计性能接近于PARAFAC算法,同时优于借助旋转不变性进行信号参数估计(Estimation of signal parameters via rotational invariance technique,ESPRIT)算法和传播算子(Propagator method,PM)算法。     

Safety assessment of approximate segregated parallel operation on closely spaced parallel runways

With the continuous growth of air traffic flow, some airports in China or other countries begin to construct Closely Spaced Parallel Runways (CSPR) to meet the capacity requirement of civil aviation. In this paper, the simulation and calculation method of flight trajectory is developed, as well as the collision risk calculation method and wake vortex encounter risk calculation method. New methods for departure and go-around procedures are proposed to achieve approximate segregated parallel operation in an attempt to obtain approximately the same results on closely spaced parallel runways as on widely spaced parallel runways. By comparing with the independent parallel departure and segregated parallel operation in ICAO Doc. 9643, it is found that the lateral separation between aircraft in this proposal is not less than the separations in the other two cases. Based on the simulation calculation of flight trajectories under different conditions, the probabilities of collision conflict and encountering wake vortex are lower than those in current operation plan. The proposed plan has no special requirements in pilot operation, control command procedures, airport facilities, or meteorological observation and prediction, so it is convenient to promote and implement at the airports with closely spaced parallel runways.     

Type synthesis of 2-DoF rotational parallel mechanisms actuating the inter-satellite link antenna

This paper focuses on the type synthesis of two degree-of-freedom (2-DoF) rotational parallel mechanisms (RPMs) that would be applied as mechanisms actuating the inter-satellite link antenna. Based upon Lie group theory, two steps are necessary to synthesize 2-DoF RPMs except describing the continuous desired motions of the moving platform. They are respectively generation of required open-loop limbs between the fixed base and the moving platform and definition of assembly principles for these limbs. Firstly, all available displacement subgroups or submanifolds are obtained readily according to that the continuous motion of the moving platform is the inter-section of those of all open-loop limbs. These subgroups or submanifolds are used to generate all the topology structures of limbs. By describing the characteristics of the displacement subgroups and submanifolds intuitively through employing simple geometrical symbols, their intersection and union operations can be carried out easily. Based on this, the assembly principles of two types are defined to synthesize all 2-DoF RPMs using obtained limbs. Finally, two novel categories of 2-DoF RPMs are provided by introducing a circular track and an articulated rotating platform, respectively. This work can lay the foundations for analysis and optimal design of 2-DoF RPMs that actuate the inter-satellite link antenna.     

基于改进A-Star算法的隐身无人机快速突防航路规划

针对现代战争中隐身无人机（UAV）在高严密的组网雷达防御体系下的生存及突防问题,提出了基于改进A-Star算法的隐身无人机战区突防航路规划技术。首先对隐身无人机突防过程进行了分析建模,分别建立了隐身无人机的运动学模型、动态雷达散射截面特性和组网雷达探测概率的计算模型。然后针对传统算法在解决隐身突防问题时的不足,充分考虑所规划航路时的快速性和安全性要求,设计了改进A-Star算法。在算法中引入了多层变步长搜索策略和无人机的姿态角信息,结合秩K融合准则,通过每段航迹上隐身无人机被组网雷达系统的发现概率来判断新航迹点的可行性。仿真结果表明,改进A-Star算法能够在复杂的组网雷达系统下快速生成更优的战区突防航路,具有一定的应用价值。     

基于改进人工蜂群算法的无人机实时航迹规划

为了适应现代战争战场环境的复杂性,针对所建立的突发威胁模型,提出了一种基于改进人工蜂群算法的无人机航迹规划方法,对无人机进行动态航迹寻优,并通过MATLAB进行了仿真验证。仿真结果表明,所设计的方法能够根据实时出现的威胁状况进行动态航迹规划、评价和选优,同时满足实时性要求。     

基于冲突距离的空中高速路换道模型

为解决航空器在空中高速路中的运行安全问题,对空中高速路平行航路换道模型进行了研究。分析了航空器换道的运动学过程,根据航空器之间的冲突距离建立了航空器的平行航路换道模型,总结了影响换道航空器之间的冲突距离的因素。最后,经仿真计算得到航空器匀速飞行时与相邻航空器不发生冲突的理论安全距离。     

基于单叶双曲面的标准Stewart并联结构六维力传感器各向同性优化设计

基于Stewart并联结构六维力/力矩传感器在空间六维力的准确检测上具有广泛前景,设计低耦合、高精度、易于标定和使用的六维力/力矩传感器是其结构设计的关键问题.传统Stewart并联结构几何参数描述为6个相互耦合的变量,不利于实现设计参数与设计指标的解耦,而且非正交条件下的各向同性使得六维力/力矩传感器仍存在耦合,为此...     

基于Event的垂直碰撞风险改进模型研究

空中交通流量的快速增长,导致空域资源紧张和大量航班延误。使用新航行技术缩小间隔标准可以有效地缓解上述问题。因此,对航路的碰撞风险进行评估具有重要意义。传统Event模型的碰撞模板是一个长方体模板,本文在前人研究的基础上提出了用椭球体代替长方体碰撞模板的思想,并对飞机穿越垂直间隔片的概率重新进行计算。结果表明,在相同条件下改进后的Event碰撞风险模型是原模型碰撞概率的53.38%,改进的碰撞风险评估模型更加精确合理。     

飞行器BLISS分布式平台的研究与实现

用matlab和VC 作为开发工具,开发出基于tcp/ip协议和windows socket的适合于飞行器BLISS的软件BLISS Platform。BLISS Platform采用客户端/服务器构架,集成了协作优化算法,是适合于多学科设计优化的分布式计算机网络软件平台。平台的底层通讯模块由VC 程序实现,仿真优化程序由matlab开发,在matlab环境下修改飞行器数学模型就可实现对不同飞行器模型的优化设计。最后用BLISS Platform并行实现了一简单的超音速飞行器概念模型的优化设计,取得了较好的结果。     

LYM-3量具研磨机装夹定位的改进

叙述了量具研磨机的结构工作原理（不含千分尺部分）以及各种参数变化对研磨的影响。对存在的问题进行了系统归类和对比分析，提出了改进方法，如单独配研磨器减少研磨行程，利用钳口铜块画刻线确定卡尺位置，找正主尺与直角尺两侧面重合而确保外量爪与滑块平行。