强不确定系统“全系数之和等于1”的实现方法

摘要： 研究强不确定系统“全系数之和等于1”的实现方法，强不确定系统指的是系统的静态增益及其界不完全确知且范围较大.“全系数之和等于1”是吴宏鑫院士20世纪80年代发现的，该原理表明，对于未知连续系统，其离散化系统的系数的和在一定条件下是1.该原理的发现对于解决闭环辨识和自适应控制的瓶颈问题具有关键作用.“全系数之和等于1”是在一定条件下成立的.为了实现系统的“全系数之和等于1”，需要对系统进行一定的变换，以满足所需条件.其中，采用静态增益的标称值的倒数进行输入变换的方法在实际中得到了广泛应用.但是，当系统的不确定性较大时，该变换将带来较大偏差.针对该问题开展了深入研究，明确给出了系统静态增益的不确定性与标称值的比值的关系对于实现“全系数之和等于1”的影响.当不确定性与标称值的比值较小时，可以近似实现“全系数之和等于1”；当比值较大时，进一步给出了通过选取合适的采样周期，近似实现“全系数之和等于1”的方法.本文的研究对于特征模型理论在实际中的应用提供了一定的基础.     

Motion synchronization in a dual redundant HA/EHA system by using a hybrid integrated intelligent control design

This paper presents an integrated fuzzy controller design approach to synchronize a dis-similar redundant actuation system of a hydraulic actuator (HA) and an electro-hydrostatic actu-ator (EHA) with system uncertainties and disturbances. The motion synchronous control system consists of a trajectory generator, an individual position controller for each actuator, and a fuzzy force tracking controller (FFTC) for both actuators. The trajectory generator provides the desired motion dynamics and designing parameters of the trajectory which are taken according to the dynamic characteristics of the EHA. The position controller consists of a feed-forward controller and a fuzzy position tracking controller (FPTC) and acts as a decoupled controller, improving posi-tion tracking performance with the help of the feed-forward controller and the FPTC. The FFTC acts as a coupled controller and takes into account the inherent coupling effect. The simulation results show that the proposed controller not only eliminates initial force fighting by synchronizing the two actuators, but also improves disturbance rejection performance.     

基于STM32的视频流图像更新方法的研究

对基于STM32系统低速(工作主频72MHz)视频流处理显示更新方案的研究。结合图像处理基本理论,分析传统的显示方法的不足,并提出一种新的视频流图像更新的方法,通过一定的实验数据和理论结果,验证该方法可行性。     

直流发电机并联供电平衡性探讨

主要介绍了某型飞机直流发电机并联供电的原理、供电时负载变化对平衡性的影响以及不平衡产生的原因,分析了影响并联供电的一般规律,并结合实际提出了预防不平衡供电的具体措施和建议。。     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

A shortcut to marking 3D target curves on curved surface via a galvanometric laser scanner

Marking arbitrary three-dimensional(3D) target curves on given objects with curved surface is required in many industrial fields, such as fabric prepreg placement in composite material part fabrication, product assembly, surface painting for decoration, etc. A shortcut to the solution of this intractable problem is proposed by utilizing a galvanometric laser scanner(GLS) with the aid of a camera. Without using the existing tedious GLS calibration procedures,the proposed method directly establishes a mapping between the 3D coordinates of the laser spots on the object surface and the control voltages of the scanner. A single-hidden layer feedforward neural network(SLFN) is employed to model the mapping. By projecting a dense grid of laser spots on the object to be marked and simultaneously taking only one image, the SLFN model is trained in minutes via a linear solving mechanism. Experiments demonstrate that the trained SLFN model has a good generalization performance for marking 3D target curves. The 3D laser marking errors on experimental objects are less than 0.5 mm. The proposed method is especially suitable for on-site use and can be conveniently extended to multiple GLSs for marking large complex objects.     

船舶燃机电机混合动力控制方法

在对现有混合动力控制系统进行研究的基础上,提出了新型的燃气轮机和异步电机混合动力系统。采用模块化的设计方法,建立了燃气轮机、异步电机、S.S.S.离合器、并车齿轮箱、并车控制器和螺旋桨等部件的数学模型,进而构建了整个系统的仿真模型。利用外特性法建立了燃气轮机的仿真模型;采用电流滞环跟踪 PWM方法建立了异步电机仿真模型,实现了弱磁调速;建立了 S.S.S.离合器的可靠的仿真模型,能够研究并车时的冲击;设计了 2种推进方式投切策略,实现了混合动力仿真;设计了并车控制器以实现并车过程调节。对混合动力控制策略和并车过程进行了仿真,结果表明所提出的混合动力系统能够正常工作,并车控制器工作较好,并车策略有效,能够减小并车过程中的冲击。     

复合材料构件热压罐成型温度场研究

在热压罐固化工艺的热历程中,复合材料零件表面温度场分布的合理与否将直接决定产品的固化质量.以工字型零件和T型加筋壁板两种复合材料零件为研究对象,使用EC-3×8M和SCH-5.5×21M两种型号热压罐,同时选择炉温偶和零件偶两种控温方式对零件进行固化.通过分析温度场测试结果发现,控温方式、设备加热方式、升降温速率、热电偶的摆放位置、固化压力等因素均对零件的温度场有影响.     

基于Kalman滤波的变体飞行器T-S模糊控制

针对变体飞行器的跟踪控制问题,提出了一种基于Kalman滤波的T-S模糊控制方法。考虑飞行器系统状态不可测,引入惯导数据作为辅助信息,利用Kalman滤波算法融合飞控信息与惯导信息实现状态估计。由于变体飞行器在不同变形结构下气动特性变化较大,为便于控制器设计,采用小扰动线性化方法得到飞行器在不同平衡点处的局部线性模型,并通过状态反馈方法设计局部控制器,局部线性模型和局部控制器通过模糊集和模糊规则聚合成一个连续光滑的全局T-S模糊模型和T-S模糊控制器。通过综合Kalman滤波器与T-S模糊控制器得到一个基于Kalman滤波的T-S模糊控制器。仿真结果表明,该控制器在变形过程中能够实现状态估计,保证飞机的跟踪性能。