折叠式变体飞行器轨迹优化及控制分析

针对临近空间高超声速飞行器存在的问题，设计了一种折叠翼飞行器，可以通过折叠机翼来适应各种飞行状态，保持最优的气动特性。并针对临近空间滑翔式高超声速的特点，采用高斯伪谱法对固定翼飞行器和折叠翼飞行器的轨迹优化，通过将折叠翼飞行器与传统固定翼飞行器在射程能力、规避热流能力方面进行对比，提出了一种综合目标的轨迹优化思想。设计的折叠翼飞行器相比传统固定翼飞行器性能更加优越，更适合临近空间环境，提高了17.67%的航程，减少了热流率峰值的35.72%，并通过控制系统的设计和仿真加以验证，仿真结果表明变体飞行器机动能力相比固定翼飞行器有了显著的提高。     

基于动态补偿的多电机控制算法

多电机协调控制达到转速一致是电机控制中的一个关键难题，外加负载变动和电机参数变化时会引起电机性能的下降，达不到良好的控制效果。为使电机间保持转速同步，建立了永磁同步电机d-q坐标系下的矢量控制数学模型，基于转速跟随控制，提出一种基于单神经元PID的变增益速度补偿器进行偏差耦合控制。在MATLAB/Simulink建立了3台永磁同步电机的仿真模型。仿真结果表明，与传统PID固定增益速度补偿器算法相比，单神经元PID的变增益速度补偿器具有更强的鲁棒性以及更快的收敛性。     

大型客机低速构型高雷诺数风洞腹撑支架干扰数值模拟

风洞到飞行相关性修正是获取现代大型客机低速气动特性的重要手段，通常采用增压提高风洞试验雷诺数，而支架干扰修正是该修正体系的一个关键环节。采用数值模拟研究了增压风洞腹撑的支架干扰，并分析了腹撑对飞机各部件的干扰及其对风洞流场的影响。通过数值模拟与风洞试验对比，表明升力系数相差0.006，阻力系数最大相差0.001 2，俯仰力矩系数最大相差0.01，验证了CFD数值模拟方法的可靠性。CFD计算结果表明：腹撑使得全机升力增加、阻力减小，俯仰力矩增加；腹撑对升力影响的主要部件是机翼，腹撑使得风洞中心以上动压增加，提升上翼面流速，从而增加了机翼的升力；与传统认识不同的是腹撑对阻力影响为负，且主要影响部件为缝翼，原因为缝翼下偏使得法矢分量向前从而减小了阻力；腹撑对俯仰力矩影响的主要部件是机身及平尾。研究结果揭示了腹撑对飞机气动特性影响的量级、主要影响部件及其流场变化，可为支架干扰数据修正及支架优化设计提供参考。所得结论可更好用于支架干扰试验的开展及风洞到飞行数据的修正，具有一定的工程实用性。     

A novel control method for turboshaft engine with variable rotor speed based on the Ngdot estimator through LQG/LTR and rotor predicted torque feedforward

In order to compensate for the disturbance of wide variation in rotor demanded torque on power turbine speed and realize the fast response control of turboshaft engine during variable rotor speed, a cascade PID control method based on the acceleration estimator of gas turbine speed (Ngdot) and rotor predicted torque feedforward is proposed. Firstly, a two-speed Dual Clutch Transmission (DCT) model is applied in the integrated rotor/turboshaft engine system to achieve variable rotor speed. Then, an online estimation method of Ngdot based on the Linear Quadratic Gaussian with Loop Transfer Recovery (LQG/LTR) is proposed for power turbine speed cascade control. Finally, according to the cascade PID controller based on Ngdot estimator, a rotor demanded torque predicted method based on the Min-batch Gradient Descent-Neural Network (MGD-NN) is put forward to compromise the influence of rotor torque interference. The simulation results show that compared with cascade PID controller based on Ngdot estimator and the one combined with collective pitch feedforward control, the novel control method proposed can reduce the overshoot of power turbine speed by more than 20%, which possesses faster response, superior dynamic effect and satisfactory robustness performance. The control method proposed can realize the fast response control of turboshaft engine with variable rotor speed better.     

民用飞机全机静力试验前机身工况配平载荷设计

民用飞机全机静力试验中由于加载方案复杂,为了简化试验加载数量,传统的配平方案主要保证考核区的加载准确性,对于非考核区的载荷简化到若干加载点上。对于飞机机身这种薄壁结构,非考核区的配平对考核区影响较大。以某飞机前机身严重工况为例,基于飞机全机有限元模型,研究静力试验的载荷配平方案;通过对比分析态载荷与传统试验态配平载荷方案下的内力解,对传统全机静力试验载荷配平方案进行优化。结果表明：优化后的试验态内力解与分析态内力解基本吻合;对于飞机机身薄壁结构,圣维南原理并不适用,全机静力试验的载荷配平要与真实工况受力情况吻合,才能达到试验验证目的。     

Conceptual design and flight test of two wingtip-docked multi-body aircraft

To overcome the drawbacks such as large wing deformations, poor performance encountering gusts, limits in taking off and landing, inconvenience of transportation of High-Altitude Long-Endurance (HALE) Unmanned Aerial Vehicles (UAVs), a new conceptual aircraft called wingtip-docked Multi-Body Aircraft (MBA) has attracted lots of attentions. Aiming to investigate the feasibility of this concept, two UAV models were designed, manufactured and connected by a wingtip-docking mechanism, which only allows the relative roll motion between the two aircraft. The trim solution of the two connected aircraft is firstly obtained by solving the developed nonlinear flight dynamic equations, followed by the stability analysis based on the linearized model. The results show that the connected aircraft is inherently unstable and cannot fly without a reasonable flight control system. A set of Proportional-Integral-Derivative (PID) control laws was then developed and implemented in the two experimental aircraft. The success of the flight tests show that the flight control can effectively eliminate the unstable motion and the wingtip-docked MBA is controllable and feasible.     

Y7-200A飞机自然结冰飞行试验

介绍了Ｙ７－２００Ａ飞机防冰除冰系统,自然结冰飞行试验所需气象专用设备和机场气象条件的选择以及自然结冰的飞行安全。同时还介绍了飞行试验的内容、试验方法及试验结果,并对试验结果进行了分析,试飞结果表明,带自然积冰飞机性能比带模拟冰型的好,自然结冰试验与模拟冰型试验之间的飞机操纵特性没有不可接受的差异,飞机飞行品质良好。可供运输类飞机自然结冰飞行试验时参考。     

液体火箭发动机典型实验室及典型实验概述

在大量文献研究的基础上,概括介绍了目前液体火箭发动机方面的典型实验室和典型实验及几种用于液体火箭发动机喷雾、燃烧和流动测量的先进仪器。为开展新一代液体火箭发动机的实验研究和设计提供参考。     

刀形检测系统及空间测量坐标系的建立

论述一种基于二维视觉的刀形检测及调位系统,给出了测量系统的机械结构以及刀具 原理,分析了系统测量坐标系建立的原理和方法,并给出相关的实验数据。系统的研制实现了高效、精确、自动的刀形检测和位置调整,为高精度数控加工提供了保障。     

铝合金锻件重复淬火保温时间对组织性能的影响

分析了铝合金锻件重复淬火保温时间的长短及其组织性能的影响情况。根据大量的试验数据,证实了重复淬火保温时间及时效保温时间的长短对锻件性能的直接影响,并以此确定了合理的工艺参数。