穿透式冷板的传热分析

对航空电子设备上采用的空心冷板冷却系统的传热特性进行了分析求解，得到了空心冷板稳态温度分布表达工和功率－温度－流量关系式，可作为空心冷板系统的设计依据，建立了空心冷板失效的动态温度模型，得到的温度－时间响应特性可用于评估冷板系统耐热冲击性能。     

飞机液压能源管路系统的振动特性分析

论述了液压能源管路网络系统的建模，着重建立了液体输管路及有关元件的传递矩阵，并给出了如何用特性阻抗法对系统进行求解，最后对飞机液压能源管路系统的动态特性进行了仿真，并指出了一些重要的影响因素。     

人工释能法求解线性代数方程组

本文建立求解线性代数方程组的人工释能法迭代格式,并给出该迭代格式收敛的充分必要条件和最佳释能时机,同时给出实现人工释能法的数值计算方法及其数值稳定性条件。     

微重力下管肋式空间辐射器的整体优化分析

建立了向一重力环境下管肋式空间辐射器传热过程的数学模型，并以单质量散热量最大和热载体驱动功率最小为优化目标，对管式空间辐射器进行了优化分析。     

Precise line-of-sight modelling for angles-only relative navigation

This work presents a precise analytical model to reconstruct the line-of-sight vector to a target satellite over time, as required by angles-only relative navigation systems for application to rendezvous missions. The model includes the effects of the geopotential, featuring: the analytical propagation in the mean relative orbital elements (up to second-order expansion), the analytical two-way osculating/mean orbital elements’ conversion (second-order in $J_2$ and up to a given degree and order of the geopotential), and a second-order mapping from the perturbed osculating elements’ set to the local orbital frame. Performances are assessed against the line-of-sight reconstructed out of the precise GPS-based positioning products of the PRISMA mission. The line-of-sight modelled over a far-range one day long scenario can be fitted against the true one presenting residuals of the order of ten arc-seconds, which is below the typical sensor noise at far-range.     

Study of GNSS-measured ionospheric total electron content variations generated by powerful HF-heating

The purpose of this work is to report the experimental evidences for the influence of perturbations in the electron density in the dayside mid-latitude ionosphere, that are caused by high-frequency heating of the F2 layer, on the GNSS signals. The experiments were carried out at the Sura heater (Radio Physical Research Institute, N. Novgorod). During the sessions of ionospheric heating with different time modulations of the radiated power the rays linking the navigational satellites with the ground receiver intersected the heated region. Variations in the total electron content (TEC) were studied; these variations are proportional to the reduced phases of navigational signals. It is shown that with the square-wave modulation of the radiated power (with periods of 1, 6, 10 and 15 min), perturbations with periods of the main modulation of heating and its harmonics appear in the spectrum of TEC variations. Examples are presented of identification of the heating-induced variations in TEC, including determination of the amplitudes and time characteristics of these variations.     

浅议信息时代高校校报的发展

在以网络为代表的新媒体无孔不入的今天,传统的报纸面临着巨大的压力,同样新媒体对高校校报的冲击无疑也是巨大的。如何在竞争激烈的新媒体时代继续引领校园舆论,是所有高校校报人所引以深思的问题。列举了信息时代以网络为核心的新媒体对高校校报的冲击,特别是在读者获取信息的方式、读者阅读兴趣、读者阅读习惯等方面的巨大影响;分析了高校校报和网络媒体在内容、形式等方面各自的长处和特点,并初步提出了高校校报机构调整和加深内涵建设等应对措施。     

强不确定系统“全系数之和等于1”的实现方法

摘要： 研究强不确定系统“全系数之和等于1”的实现方法，强不确定系统指的是系统的静态增益及其界不完全确知且范围较大.“全系数之和等于1”是吴宏鑫院士20世纪80年代发现的，该原理表明，对于未知连续系统，其离散化系统的系数的和在一定条件下是1.该原理的发现对于解决闭环辨识和自适应控制的瓶颈问题具有关键作用.“全系数之和等于1”是在一定条件下成立的.为了实现系统的“全系数之和等于1”，需要对系统进行一定的变换，以满足所需条件.其中，采用静态增益的标称值的倒数进行输入变换的方法在实际中得到了广泛应用.但是，当系统的不确定性较大时，该变换将带来较大偏差.针对该问题开展了深入研究，明确给出了系统静态增益的不确定性与标称值的比值的关系对于实现“全系数之和等于1”的影响.当不确定性与标称值的比值较小时，可以近似实现“全系数之和等于1”；当比值较大时，进一步给出了通过选取合适的采样周期，近似实现“全系数之和等于1”的方法.本文的研究对于特征模型理论在实际中的应用提供了一定的基础.     

Potential of IRNSS/NavIC L5 signals for ionospheric studies

Indian Space Research Organization (ISRO) has developed an indigenous system named Indian Regional Navigation Satellite System (IRNSS) or NavIC (Navigation with Indian Constellation), that consists of 7 satellites and transmits navigation signal in L and S bands. ISRO, for validation of the system, has installed many IGS (IRNSS/GPS/SBAS) receivers scattered over the Indian region. Using preliminary data from two geographically widely separated stations over India, this paper presents the results on studies on parameters of IRNSS signal quality and discusses how these parameters may be used to study the ionospheric behavior over the Indian region. The results show the importance and advantages of using IRNSS data for such studies.     

气动钣金快速成形机的研制

针对电动钣金成形机制造成本高、效率低、易产生死点的问题,提出一种采用气液增力装置代替液压传动系统的气动钣金成形机设计方案。气液增力装置采用精密气压转换阀控制,实现行程平稳控制和加工成形过程平稳加载,显著提高了生产效率;配套研制的多种无齿收缩成形模具,可加工不同形状钣金件并获得更好的表面质量。该技术在钣金快速成形方面的研究处于国内领先水平,已获得3项国家专利。