基于H∞方法的控制系统作动器最优控制仿真研究

在设计控制系统模型时,首先引入了有限差分法(FDM)离散化后的波动方程,然后基于H∞最优控制原理,检查闭环控制系统的稳定性和可探测性,对控制系统传感器和作动器的位置进行优化配置.通过计算闭环反馈系统的范数,最终得到了控制系统的最优控制算法.仿真结果表明,利用波动方程来优化控制系统传感器和作动器位置的算法是可行的,可广泛应用于飞控系统的设计中.     

一种卫星信道的反馈优化接入机制

提高卫星信道资源利用率，探索高效可行的端站接入机制是卫星通信发展亟待解决的问题之一。当前卫星通信DVB-RCS标准基于带宽预先规划的接入机制与端站随遇接入的需求矛盾凸显，因此提出一套信道反馈优化接入机制，综合考虑各端站数据业务需求，在不改变原有协议信令特征的基础上，探索性地引入谦虚度激励方法，创造性地构造动态协商反馈模型并加以求解，达到提高端站接入数量、满足随遇接入需求、提升信道利用效率、最大化整体带宽通信业务效益的目的。通过试验验证，带宽分配反馈优化机制比传统模式提高近1倍接入率，最大端站数接入时算法耗时约只有0.67s，可为卫星信道使用提供技术参考。     

基于改进准则法的复合壳阻尼结构拓扑减振动力学优化

针对复合壳阻尼结构的拓扑减振优化问题，以约束阻尼层的有限单元为设计变量，采用体积比、模态频率和振型为优化约束条件，构建以多模态权重系数的结构模态损耗因子数值关系为优化目标函数的拓扑减振优化模型。为了拓展优化目标灵敏度具有不局限于某一变密度法插值模型的形式，推导了数值表达式的一般函数式。动力学优化中优化目标灵敏度正、负数集共存，使得非凸性的目标函数设计变量出现负值或优化函数寻优于局部极值点。为此，推导出复合壳阻尼结构的全域灵敏度改进优化准则法迭代格，以确保每次迭代域均为全域设计变量集。结合有限单元法编程实现了复合壳阻尼结构改进准则法，并对复合壳结构进行拓扑减振优化分析。结果表明：在敷设体积减为全覆盖的50%时，复合壳结构的模态损耗因子增减偏差为10%，具有提升减振的轻量化设计目的；各阶目标函数和拓扑构型所需的迭代次数少，中间密度区域较小，多阶优于单阶模态优化函数，易于获得全域寻优的有效减振。     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

Particle swarm optimization applied to hypersonic reentry trajectories

This paper presents the novel use of the particle swarm optimization(PSO)to generate the end-to-end trajectory for hypersonic reentry vehicles in a quite simple formulation.The velocitydependent bank angle profile is developed to reduce the search space of unknown parameters based on the constrained PSO algorithm.The path constraints are enforced by setting the fitness function to be infinite on condition that the particles violate the maximum allowable values.The PSO algorithm also provides a much easier means to satisfy the terminal conditions by adding penalty terms to the fitness function.Furthermore,the approximate reentry landing footprint is fast constructed by incorporating an interpolation model into the standardized bank angle profiles.Numerical simulations demonstrate that the PSO method is a feasible and flexible tool to generate the end-to-end trajectory and landing footprint for hypersonic reentry vehicles.     

几种生长模型参数的最小二乘估计方法及应用

提出一种Logistic模型、Gompertz模型、Mitscherlich模型和Bertallanffy模型的分布参数估计方法，这种方法以加权最小二乘法为基础，推导求解分布参数的方程组。利用这类曲线模型中参数形式的特点，使同时求解三个参数的问题简化为同时求解两个参数的问题，并给出求解参数耦合方程组的二重二分迭代法。预测地基沉降的计算实例表明，这种方法对于迭代初值的选取要求较低、求解速度快、精度高，而且通过选取权因子可以对已有数据实现“重近轻远”的处理。     

基于ALE法的水陆两栖飞机船体着水性能分析

水陆两栖飞机的着水性能是体现其综合性能的重要因素之一.应用ALE法对三种水陆两栖飞机船体截面进行入水仿真计算,从着水载荷、喷溅性能及运动响应三个方面对着水性能进行综合评估.对比分析了直线型、带舭弯弧形、复合型三种构型截面在不同速度、不同重量下的压力分布、喷溅性能以及运动响应,得到了三种截面横向压力分布规律.计算结果显示相同状态下,喷溅性能复合型优于带舭弯弧形、带舭弯弧形优于直线型;过载复合型远大于带舭弯弧形,带舭弯弧形稍大于直线型,综合看来带舭弯弧形截面着水性能最佳.     

基于非线性变换的加速度计误差标定与补偿CSCD

为提高三轴加速度计测量精度,分析其误差来源和产生机理,建立了误差模型;根据误差模型和重力场幅值不变特性,推导出非线性观测方程。引入两个未知的参数向量,通过数学变换把非线性观测方程变形为关于新未知参数的线性方程;然后采用批量最小二乘法求出新的未知参数,并根据误差模型参数和新未知参数之间的关系,利用逆解析运算求出对应的零点偏差、灵敏度误差和三轴不正交误差。实验结果表明,加速度计正负误差峰值间距可以减小100倍左右,精度可达10-3m/s2,并具有很好的可重复性。该方法算法效率较高,补偿效果显著。     

谐振电路中品质因数的计算方法

从品质因数的原始定义出发,分别计算出简单RLC串、并联电路的品质因数,得到两个结论,并将其推广,提出了两种简单的计算品质因数的方法,最后通过求解一个实际的LC并联谐振电路的品质因数得到验证。     

Theoretical aspects of selecting repeated unit cell model in micromechanical analysis using displacement-based finite element method

Repeated Unit Cell(RUC)is a useful tool in micromechanical analysis of composites using Displacement-based Finite Element(DFE)method,and merely applying Periodic Displacement Boundary Conditions(PDBCs)to RUC is almost a standard practice to conduct such analysis.Two basic questions arising from this practice are whether Periodic Traction Boundary Conditions(PTBCs,also known as traction continuity conditions)are guaranteed and whether the solution is independent of selection of RUCs.This paper presents the theoretical aspects to tackle these questions,which unify the strong form,weak form and DFE method of the micromechanical problem together.Specifically,the solution’s independence of selection of RUCs is dealt with on the strong form side,PTBCs are derived from the weak form as natural boundary conditions,and the validity of merely applying PDBCs in micromechanical Finite Element(FE)analysis is proved by referring to its intrinsic connection to the strong form and weak form.Key points in the theoretical aspects are demonstrated by illustrative examples,and the merits of setting micromechanical FE analysis under the background of a clear theoretical framework are highlighted in the efficient selection of RUCs for Uni Directional(UD)fiber-reinforced composites.