Experimental investigation on aero-heating of rudder shaft within laminar/turbulent hypersonic boundary layers

The aero-heating of the rudder shaft region of a hypersonic vehicle is very harsh, as the peak heat flux in this region can be even higher than that at the stagnation point. Therefore, studying the aero-heating of the rudder shaft is of great significance for designing the thermal protection system of the hypersonic vehicle. In the wind tunnel test of the aero-heating effect, we find that with the increase of the angle of attack of the lifting body model, the increasement of the heat flux of the rudder shaft is larger under laminar flow conditions than that under turbulent flow conditions. To understand this, we design a wind tunnel experiment to study the effect of laminar/turbulent hypersonic boundary layers on the heat flux of the rudder shaft under the same wind tunnel freestream conditions. The experiment is carried out in the ?2 m shock tunnel(FD-14 A) affiliated to the China Aerodynamics Research and Development Center(CARDC). The laminar boundary layer on the model is triggered to a turbulent one by using vortex generators, which are 2 mm-high diamonds. The aero-heating of the rudder shaft(with the rudder) and the protuberance(without the rudder) are studied in both hypersonic laminar and turbulent boundary layers under the same freestream condition. The nominal Mach numbers are 10 and 12, and the unit Reynolds numbers are2.4 × 10~6 m~(-1) and 2.1 × 10~6 m-1. The angle of attack of the model is 20°, and the deflection angle of the rudder and the protuberance is 10°. The heat flux on the model surface is measured by thin film heat flux sensors, and the heat flux distribution along the center line of the lifting body model suggests that forced transition is achieved in the upstream of the rudder. The test results of the rudder shaft and the protuberance show that the heat flux of the rudder shaft is lower in the turbulent flow than that in the laminar flow, but the heat flux of the protuberance is the other way around,i.e., lower in the laminar flow than in the turbulent flow. The wind tunnel test results is also validated by numerical simulations. Our analysis suggests that this phenomenon is due to the difference of boundary layer velocities caused by different thickness of boundary layer between laminar and turbulent flows, as well as the restricted flow within the rudder gap. When the turbulent boundary layer is more than three times thicker than that of the laminar boundary layer, the heat flux of the rudder shaft under the laminar flow condition is higher than that under the turbulent flow condition. Discovery of this phenomenon has great importance for guiding the design of the thermal protection system for the rudder shaft of hypersonic vehicles.     

跨声速风洞模型主动减振系统试验研究

为解决跨声速风洞测力试验模型的俯仰振动问题,研制了一套主动减振系统。该系统利用了模型/天平/支杆系统的响应特性,采用主动控制方法,以天平信号作为输入,采用速度负反馈,使用安装在支杆后端主动接头内的压电陶瓷作动器来抑制模型振动。地面试验结果表明,主动减振系统使模型/天平/支杆系统的俯仰一、二阶阻尼比分别提高20.8倍和12.8倍。风洞试验结果显示,法向力和俯仰力矩振动幅度分别下降71.0%和57.5%,风洞试验结果还表明主动减振系统对气动系数的影响相对较小。主动减振系统在多个模型的风洞试验中也得到验证,显示出良好的减振性能和模型适应性。     

节能高效数字化兆瓦级风电变流器试验系统

针对现有风电变流器试验系统能量损耗高、试验效率低的问题,提出了一种基于环形功率回馈的试验方法。重点阐述了试验系统的基本原理与结构,并搭建了变流器试验软硬件平台,实现了对变流器各特性参数的自动测试要求。对兆瓦级风电变流器进行了相应的试验,试验结果表明:该系统试验效率优,而且系统操作方便,安全可靠,可实现变流器试验系统的高效节能与数字化。     

结冰云雾参数对冰与固壁间剪切强度影响的初步研究

基于结冰风洞实验段,建立了冰与固壁间黏附界面剪切强度测量实验装置,获得了合理的剪切强度范围。在0.3 m×0.2 m结冰风洞实验段内开展了冰与固壁间黏附界面剪切强度的测量实验。掌握了结冰环境温度、平均水滴直径等结冰云雾参数对冰与固壁间黏附剪切强度的影响规律。研究表明:结冰环境温度为-15~-10 ℃间出现了剪切强度极大值。来流速度越大,水滴的惯性力越大,水滴间的间隙越容易被填充,冰与固壁间剪切强度也就越大。平均水滴直径(MVD)为35 μm附近出现了剪切强度极小值,水滴直径越小,水滴之间的间隙就越小,结冰就越致密。水滴直径越大,水滴越容易发生平铺,水滴之间的间隙就容易被填充,反而造成剪切强度增大。      

直驱风电场并网对系统静态电压稳定性的影响

风电场的大规模接入会对电网静态电压稳定性造成不容忽视的影响。以含直驱风电机组的扩展单机无穷大系统为例,通过2种静态潮流计算方法对含直驱风机的系统等值模型进行分析,推导风电接入后系统并网点母线电压的解析式。在BPA中分别建立含直驱风电机组的扩展单机无穷大系统以及实际电网系统的仿真模型,对比理论计算结果与仿真试验结果。分析并网点母线电压在不同控制方式下,风电渗透率、风机并网位置、负荷接入比例和负荷接入位置等因素对系统静态电压稳定性的影响。     

基于有效透气量对火星降落伞气动力系数预测分析

针对火星探测任务中降落伞开伞环境为低密度大气的特点,本文由降落伞气动力系数与透气量关系,提出了通过降落伞有效透气量预测降落伞气动力系数的方法,该方法先由织物透气量试验获取伞衣透气量拟合曲线和透气量常数,再根据风洞试验得到两种有效透气量下的气动力系数,然后由有效透气量插值获取了盘缝带(DGB)伞火星大气条件下气动力系数,并且通过空投试验数据对该方法进行验证。计算结果表明,在火星条件下,降落伞气动力系数与风洞条件下变化趋势基本一致。Ma 0.4工况阻力系数的变化范围为0.583～0.622,Ma 0.8工况阻力系数的变化范围为0.438～0.494。     

从摄动理论看洞壁干扰的总体型修正

利用Ｄ．Ｎｉｘｏｎ跨声速摄动理论对目前奉行的洞壁干扰总体型修正提出了质疑;讨论了结果从理论上进一步支持了洞壁干扰的当地型修正战略。     

模型旋翼风洞试验中变距拉杆载荷的测量

桨叶变距拉杆操纵载荷是旋翼设计的重要参数之一。在参考了常规飞机模型风洞试验测力元件及国外测量方法的基础上,研制了具有足够刚度和强度,且有较高载荷灵敏度的新式变距拉杆测力元件,解决了高刚度与高的载荷灵敏度要求这一矛盾。同时采用了信号放大技术,将其成功地应用于旋翼模型试验,并获得了操纵载荷这一重要参数     

低速闭口风洞模型张线支撑及内天平测量系统的研制

“张线支撑及内天平测量系统”已在ＦＬ－８ 闭口风洞中调试、使用。该系统使用了套管天平,套管内杆是天平与模型相连,与天平相连的套管是支撑体,张线的一端与套管的前后吊点相连,张线的另一端与风洞上转盘齿圈上的张紧机构和风洞下转盘下的配重相连。该系统的角度变化范围,模型侧吊时, α＝ ±３６０°,β＝ ±６５°,模型正吊时,α＝ ±６５°,β＝ ±３６０°实验表明：张线支撑与尾撑和腹撑相比,消除了由于支杆引起的模型振动,其支架干扰变小,试验数据质量有了进一步的提高     

弹性模型实验技术

介绍了火箭弹性模型实验技术,包括模型对火箭的质量分布、刚度分布的模拟,模型的加工制做,激振机构的研制,支撑元件的研制以及几期实验的结果综合。