无刷双馈电机静止坐标系数学模型的研究

由于没有电刷和滑环,提高了运行的可靠性,降低了维护成本,因此无刷双馈电机(BDFM)在变速恒频发电领域有着广阔的应用前景。由于特殊的结构和工作原理,BDFM数学模型十分复杂。从BDFM多回路空间矢量数学模型出发,推导出了两个静止坐标系之间的坐标变换关系以及功率绕组静止坐标系数学模型和控制绕组静止坐标系数学模型,推导过程简洁明了。所得结果为BDFM理论分析和不同控制策略的研究提供了理论基础。MATLAB/Simulink环境下的仿真结果验证了数学模型及坐标变换关系的正确性。     

直线电机位置伺服系统的增强复合非线性控制

针对高性能机电系统中常用的直线伺服电机,设计了一个能实现快速与准确的定点运动的位置控制器。控制器采用线性控制律与平滑非线性控制律相结合的方案,并利用一个降阶线性状态观测器对电机运动速度(未量测)加以估计。为了消除未知扰动带来的稳态误差,控制律中嵌入了积分控制作用。整个控制律采用全参数化设计,可实现动态增益控制,方便了在线参数整定与性能优化。控制方案应用于一个实际的永磁直线电机位置伺服系统,基于TMS320F28335 DSC进行了试验测试,结果表明系统能对各目标位置进行准确的跟踪,且具有理想的瞬态性能。     

应用于超级电容储能系统的双向DC/DC变换器混沌控制方法研究

超级电容储能系统(SCESS)主要通过对双向DC/DC变换器进行控制来快速平抑直流母线电压的波动。为了抑制控制过程中所产生的一些分岔和混沌现象,提出了一种应用于SCESS的混沌控制方法。分析了该方法的控制原理,并根据非线性动力学理论建立了双向DC/DC变换器的离散迭代模型;然后设计了一种能够自动调节补偿斜率的混沌控制信号;最后对该信号作用下的异步切换函数和同步切换映射式进行了数值求解,从而绘出系统分叉图。通过仿真和试验证明,该方法能够有效抑制SCESS的分岔和混沌现象,提高了系统的稳定工作范围和动态响应速度。     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

点火瞬态过程仿真模型参数辨识

建立了固体火箭发动机点火瞬态过程一维非定常流场仿真模型,采用系统辨识方法进行了模型参数不确定性研究。基于点火试验用缩比发动机试验结果,得到了传热模型参数和瞬态燃速模型参数的最优估计,提高了点火瞬态过程一维仿真模型的预估精度。采用近似方法,构建Kriging近似函数,有效解决了一维非定常流场仿真的计算复杂性问题。     

价电子分形燃烧模型在高能固体推进剂中的应用

在价电子燃烧模型的基础上引进分形理论,提出复合固体推进剂的价电子分形燃烧模型,在此基础上进行了高能固体推进剂燃速和压强指数的模拟计算,研究了固体填料粒径和压力对燃速的影响规律。结果表明,价电子分形燃烧模型适用于高能固体推进剂的燃烧性能计算,燃速及压强指数模拟计算结果与测试结果吻合较好,大部分误差在±10%范围以内。     

考虑外圈局部缺陷的滚动轴承非线性动力特性

 建立了考虑滚动轴承外圈局部缺陷、非线性轴承力和径向游隙等非线性因素的滚动轴承系统动力学微分方程,并用Runge-Kutta-Felhberg算法对其求解。利用分岔图、Poincaré映射图、频谱图以及均方值、峰值因子、峭度等时域参数,分析了滚动轴承的响应、分岔和混沌等非线性动力特性。结果表明：考虑外圈局部缺陷的滚动轴承系统存在多种周期、拟周期和混沌响应;滚动轴承系统进入混沌的主要途径是倍周期分叉;峰值因子比率在中、低速,峭度比率在低速时可以很好地识别外圈局部缺陷。均方值比率除了在与轴承动力特性有关的个别转速外,可以在较大的转速范围识别外圈局部缺陷。     

军用飞机环境适应性评价模型

阐述了作战飞机面临的环境,分析了各种环境因素对军用飞机作战性能的影响,建立了军用飞机环境适应性评价指标体系。确定了机场环境剖面和衡量各个评价因素样本数据的方法,并提出了军用飞机环境适应性评价模型,通过实例验证了模型的合理性和方法的可行性。算例和分析结论表明,该模型反映了军用飞机在环境适应性方面的技术要求,同时也为军用飞机在环境适应能力上的改进提供了参考。     

结构的概率-非概率混合可靠性模型

将影响结构可靠性分析的不确定性因素用概率和非概率两种方式模拟。并基于结构可靠性分析中的概率可靠性模型和非概率集合可靠性模型,提出一种新的结构可靠性分析的概率-非概率混合模型。该模型首先通过将功能函数进行非概率可靠性分析,然后将标准化区间变量空间所有区域的可靠度进行求和计算,从而给出结构的可靠度。并根据相同的不确定信息,由混合可靠性模型与概率可靠性模型得到的结果是相等的,证明了方法的有效性。最后,通过一个典型结构和一个机翼下壁加筋板与传统概率可靠性模型进行比较,表明该混合模型对于结构的分析和设计更为合理,能够更好地保证结构的安全性。