表面处理对17-4PH不锈钢抗固体粒子冲蚀性能的影响

为对比研究表面处理对17-4PH不锈钢抗固体粒子冲蚀性能的影响,在17-4PH不锈钢表面进行了多弧离子镀陶瓷/金属多层膜制备、激光表面合金化(LSA)处理和超音速火焰喷涂(HVOF)硬质合金层处理,利用划痕仪、自组装的不锈钢抗固体粒子冲蚀(SPE)装置、多冲疲劳试验机对上述三种表面处理试样的小攻角和大攻角SPE失效行为和机理进行了研究。结果表明,微切削是17-4PH不锈钢及其表面改性试样小攻角下固体粒子冲蚀破坏的主要失效机制,多冲型疲劳破坏是17-4PH不锈钢及其表面改性试样大攻角下固体粒子冲蚀的主要失效机制。HVOF WC-17Co涂层可显著提高17-4PH不锈钢30°小攻角和90°大攻角下SPE抗力。激光表面合金化层能够改善17-4PH不锈钢抗30°小攻角和90°大攻角下SPE性能,但SPE性能改善效果弱于HVOF喷涂涂层。TiAl N/Ti多层膜不能显著提高17-4PH不锈钢抗30°小攻角和90°大攻角的SPE性能。     

不同酚醛树脂对芳纶纸蜂窝性能的影响

为研究酚醛树脂对芳纶纸蜂窝性能的影响,本文采用两种不同的酚醛树脂制备芳纶纸蜂窝芯材,对所制备蜂窝芯材的压缩性能和剪切性能进行测试,同时结合蜂窝端面树脂分布观察、树脂与芳纶纸接触角测量等方法,分析了两种树脂所制备蜂窝芯材性能出现差异的原因,结果表明：树脂中溶剂水的挥发速度、树脂与芳纶纸之间的表面张力会影响树脂在蜂窝壁上的树脂分布;蜂窝芯材树脂含量相同时,其节点两侧的树脂胶柱有利于提高蜂窝芯材压缩强度,但树脂堆积在节点后会降低蜂窝壁厚,造成蜂窝的剪切强度和模量下降。     

芳纶纸蜂窝外观缺陷分析

文摘对芳纶纸蜂窝的制备工艺流程进行了简单的介绍,结合其制备工艺,对蜂窝双层壁、嵌套孔格、S型孔格和人字形孔格等常见外观缺陷产生的原因进行了分析,并结合蜂窝制备过程提出了减少蜂窝缺陷的具体措施。建议研究人员评估芳纶纸蜂窝外观缺陷对其性能的影响,确定缺陷的可接受范围。     

扩散连接界面缺陷对Ti-6Al-4V合金力学性能的影响

研究了φ4mm与φ2mm的扩散连接界面缺陷对Ti-6Al-4V合金力学性能的影响。当拉伸载荷方向与缺陷平面平行时,材料的强度与塑性与无缺陷材料相当,这是由于此类缺陷对样品受力截面的面积几乎没有影响。含有φ4mm缺陷试样的拉压疲劳寿命展现出很大的分散性,界面缺陷并未成为裂纹萌生的唯一位置。从表面起裂的样品均处于高寿命区域,而绝大部分从缺陷处起裂的样品均落于低寿命区域。有限元分析表明,当缺陷位于中心位置时其引起的应力集中较小,应力分布梯度较小;缺陷位于边缘位置时,应力集中效应增大。     

微硅加速度传感器的动态特性补偿方法研究

提出了一种用以扩展加速度传感器使用频率范围的动态特性补偿方法,其基本原理是根据加速度传感器的输入输出传递函数,构造出一个基于硬件的补偿网络,这个补偿网络的传递函数的零极点分别与加速度传感器的传递函数的极零点相抵消,从而使由加速度传感器输出的信号经过补偿环节后其动态特性得到补偿,扩展了加速度传感器的使用频带,同时并不要求加速度传感器处于临界阻尼状态。     

基于KBE的飞机板金件工艺性审查系统

由于板金零件的可成形性取决于多方面的因素,板金零件成形的工艺性审查也就显得十分复杂,工艺审查的合理性和准确性往往成为飞机设计和制造的矛盾焦点.通过分析当前我国飞机板金零件工艺性审查的现状,提出了在工艺性审查中利用基于知识的(KBE,Knowledge Based Engineering)技术的必要性.分析了利用后台数据库及知识库创建工艺性审查系统的总体结构和实现方案,并对系统创建中的关键技术及解决方法进行了研究.通过实例验证了该系统的功能及可靠性.      

Orbital phase spectroscopy of four high mass X-ray binary pulsars to study the stellar wind of the companion

Our work focuses on a comprehensive orbital phase-dependent spectroscopy of the four High Mass X-ray Binary Pulsars (HMXBPs) 4U 1538-52, GX 301-2, OAO 1657-415 and Vela X-1. We hereby report the measurements of the variation of the absorption column density and iron-line flux along with other spectral parameters over the binary orbit for the above-mentioned HMXBPs in elliptical orbits, as observed with the Rossi X-ray Timing Explorer (RXTE) and the BeppoSAX satellites. A spherically symmetric wind profile was used as a model to compare the observed column density variations. Out of the four pulsars, only in 4U 1538-52, we find the model having a reasonable corroboration with the observations, whereas in the remaining three the stellar wind seems to be clumpy and a smooth symmetric stellar wind model appears to be quite inadequate in explaining the data. Moreover, in GX 301-2, neither the presence of a disk nor a gas stream from the companion was validated. Furthermore, the spectral results obtained in the case of OAO 1657-415 and Vela X-1 were more or less similar to that of GX 301-2.     

The role of AVDR in linear cascade testing

Linear cascade testing plays an important role in the research and development of turbomachinery and is widely used over the world.The ideal cascade model of a turbomachinery blade row is two-dimensional.In actual linear cascade testing, the flow through the test section converges due to the development of the boundary layer and secondary flow along the sidewall surfaces of the test section.Axial velocity density ratio(AVDR) is adopted to account for the deviation of the tested cascade flow from the ideal 2D model.Among numerous published cascade works, the influence of AVDR on cascade performance is seen to be complicated with many affecting factors, such as those related to cascade/blade geometry and flow conditions.Also, controlling AVDR is limited by the facility capability.Furthermore, real blade-to-blade flow in turbomachines is usually associated with AVDR greater than unity due to limited span of blades between the hub and shroud such that cascade testing without reducing AVDR could be favored sometimes.All these facets add complexity and diversification to the matter.The current paper reviews previous studies and results on AVDR.Consolidated understanding on the role of AVDR and recommendations on how to deal with it in linear cascade testing are provided.      

某型航空发动机前支承动刚度的有限元分析

对某型航空发动机前支承结构的简化问题进行了探讨,根据实际发动机图纸利用UG软件建立了前支承结构三维实体模型。利用ANSYS软件对该模型进行了模态计算,得到前八阶模态。根据谐响应分析基本理论,对前支承结构进行了谐响应分析,求得静子支承系统前支承在简谐激振力下的频率响应曲线。根据动刚度定义利用MATALB编程计算得出了静子支承系统前支承动刚度曲线。