DORIS processing at the European Space Operations Centre

This paper gives an overview of the DORIS related activities at the Navigation Support Office of the European Space Operations Centre. The DORIS activities were started in 2002 because of the launch of the Envisat satellite where ESOC is responsible for the validation of the Envisat Precise Orbits and a brief overview of the key Envisat activities at ESOC is given. Typical orbit comparison RMS values between the CNES POE (GDR-C) and the ESOC POD solution is 6.5, 18.8 and 23.1 mm in radial-, along- and cross-track direction. In the framework of the generation of the ITRF2008 ESOC participated in the reprocessing of all three space geodetic techniques; DORIS, SLR, and GPS. Here the main results of our DORIS reprocessing, in the framework of the International DORIS Service (IDS), are given. The WRMS of the weekly ESOC solution (esawd03) for the 2004–2009 period compared to the IDS-1 combined solution is of the order of 12 mm. Based on the long time series of homogeneously processed data a closer look is taken at the estimated solar radiation pressure parameters of the different satellites used in this DORIS analysis. The main aim being the stabilization of the Z-component of the geocentre estimates. We conclude that the ESOC participation to the IDS ITRF2008 contribution has been beneficial for both ESOC and the IDS. ESOC has profited significantly from the very open and direct communications and comparisons that took place within the IDS during the reprocessing campaign.     

工程方法确定翼面载荷研究

提供一种使用翼面载荷测试的弯、扭矩确定气动载荷分布的工程方法。实例表明这种方法是一种比较简单易行的方法,可以得到工程上较为满意的结果。可供强度工作者参考使用。     

飞机反区时的操纵策略特性及物理机理研究

针对飞机在低动压飞行(如着舰)时处于阻力曲线反区所采用的Frontside操纵和Backside操纵方式,分别从指令控制、风扰抑制、执行机构影响三种情况对两种操纵策略的性能进行了仿真比较,得出相关结论,并分析了其内在物理原因。研究结果表明,Backside操纵性能优于Frontside操纵,具有响应快、超调小、无初始负调、抗风鲁棒性强,以及俯仰角、迎角和升降舵变化小等特点,但同时速度和推力变化大,且执行机构相位滞后对Backside操纵性能影响较大。     

基于AMESim的某型客机舵面液压系统仿真分析

当某型客机飞控舵面作为液压能源系统的用户时,应用AMESim仿真软件,在相应的载荷作用下,对液压系统所需压力、流量以及相关液压附件参数的设置进行分析,并对舵面的仿真运动结果进行动画演示。     

球形粒子在流体中的跟随性

本文从Maxey和Riley的粒子运动基本方程出发,得到了球形固体粒子在相对流动雷诺数很小情形下的分析解。讨论了粒子跟随性对外力、初始条件和流场性质的依赖关系;对均匀湍流场,分析了不同密度比和扰动频率对跟随性的影响     

气固两相透平叶片冲蚀特性的气动试验研究

在自行研制风洞中先后对应用较广的MCrAlY叶片涂层和2Cr12Mo-5叶片合金、钢丸表面强化试件在不同气流速度、颗粒冲角、颗粒性状、颗粒粒度的条件下进行了气动冲蚀试验。试验结果表明,无论是涂层还是合金,冲蚀率均随冲蚀颗粒的累积质量呈线性变化;由对比可知,其它条件相同的情况下,涂层在广泛的冲角范围内较合金的冲蚀率更小,表面的"烧结"特征,能减小叶片的冲蚀率;表面呈多棱的石英砂颗粒对试件的冲蚀程度强于带突圆球状的催化剂颗粒;在该试验范围内,相同材质的颗粒,粒度愈大,对试件的冲蚀率愈大;钢丸表面强化工艺兼有防冲蚀的能力。试验结果将为优化叶片选材、简化叶片维修技术、降低叶片维修成本提供有益的参考。     

耐高液（气）压部附件测试系统的开发

飞机上耐高液（气）压部附件易发生泄漏破损等问题，对飞机的安全运行至关重要。本文开发了一种测试系统，以气体和液体为介质，以飞机蓄压器为例，通过压力检查、泄露测试、摩擦阻力测试，检测待测部件是否合格。检测结果证明，该测试系统可作为飞机机械系统耐高液（气）压部附件检测的一种参考方法。     

不同型线结构船艏表面压力特性对比实验研究

为优选船艏结构型线方案,在风洞中针对三个在结构型线上仅有细微差别的船艏方案进行表面压力特性对比测试。实验获得了各型线方案模型表面压力空间分布特性和压力脉动特性,并通过表面压力特性的综合对比进行了结构型线评估,为船艏的结构型线设计提供直接的技术依据。     

A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.