旋翼桨叶动力学设计技术

桨叶动力学设计,其实质是求解非线性高维动力学逆问题的具体实施。本文较全面地阐述了这方面的进展情况,提出了切实可行、有效实用的数值方法。     

Experimental investigation and correlation development of jet impingement heat transfer with two rows of aligned jet holes on an internal surface of a wing leading edge

Extensive experimental studies on the heat transfer characteristics of two rows of aligned jet holes impinging on a concave surface in a wing leading edge were conducted, where50000 Rej 90000, 1.74 H/d 27.5, 66° a 90°, and 13.2 r/d 42.03. The finding was that the heat transfer performance at the jet-impingement stagnation point with two rows of aligned jet holes was the same as that with a single row of jet holes or the middle row of three-row configurations when the circumferential angle of the two jet holes was larger than 30°. The attenuation coefficient distribution of the jet impingement heat transfer in the chordwise direction was so complicated that two zones were divided for a better analysis. It indicated that: the attenuation coefficient curve in the jet impingement zone exhibited an approximate upside-down bell shape with double peaks and a single valley; the attenuation coefficient curve in the non-jet impingement zone was like a half-bell shape, which was similar to that with three rows of aligned jet holes; the factors,including Rej, H/d and r/d, affected the attenuation coefficient value at the valley significantly.When r/d was increased from 30.75 to 42.03, the attenuation rates of attenuation coefficient increased only by 1.8%. Consequently, experimental data-based correlation equations of the Nusselt number for the heat transfer at the jet-impingement stagnation point and the distributionof the attenuation coefficient in the chordwise direction were acquired, which play an important role in designing the wing leading edge anti-icing system with two rows of aligned jet holes.     

高转速风扇叶片外物撞击损伤的定量评价方法

外物撞击是造成航空发动机风扇叶片变形、损伤甚至断裂的主要因素。针对外物撞击持续时间短、瞬间载荷大、损伤影 响因素多，难以进行定量损伤评价的问题，提出基于叶片损伤参数α的叶片损伤定量评价方法。以发动机风扇叶片受冰撞为例， 采用非接触叶尖计时测量方法，对叶片撞击产生的叶尖位移进行监测分析，验证了该方法的可行性。采用瞬态动力学分析方法对 叶片经受撞击过程进行全流程仿真模拟，并采用正交试验法定量研究了外物撞击过程中的撞击速度、叶片转速、撞击位置3种因 素对叶片损伤参数α的影响，拟合回归方程并绘制了这3种因素的3D响应曲面图，得到各因素的影响权重。结果表明：冰块速度 与撞击位置同时下降时，叶片损伤弱化效果显著。该方法可为大型风扇叶片抗外物打击性能设计和在役健康监测提供理论支撑。     

Lift coefficient prediction at high angle of attack using recurrent neural network

In this paper, identification of dynamic stall effect of rotor blade is considered. Recurrent Neural Networks have the ability to identify the nonlinear dynamical systems from training data. This paper describes the use of recurrent neural networks for predicting the coefficient of lift (C_Z) at high angle of attack. In our approach, the coefficient of lift (C_Z) obtained from the experimental results (wind tunnel data) at different mean angle of attack θ_mean is used to train the recurrent neural network. Then the recurrent neural network prediction is compared with experimental ONERA OA212 airfoil data. The time and space complexity required to predict C_Z in the proposed method is less and it is easy to incorporate in any commercially available rotor code.     

主/从动式组合旋翼悬停状态气动特性分析

针对传统直升机构型中主旋翼旋转时产生的扭矩需要尾翼或是反向旋转的共轴旋翼加以抵消,从而造成能量浪费的问题,以将主旋翼旋转时产生的扭矩转化为升力为出发点,提出了一种主旋翼带动下方无动力旋翼旋转的主/从动式组合旋翼气动布局构型。通过动量叶素理论以及CFD数值模拟中的多重参考系法,对主/从动式组合旋翼悬停状态的气动特性进行了初步分析,结果表明,此构型中的下方从动旋翼利用上方主动旋翼的扭矩产生了额外10%的升力,同时下方从动旋翼在上方主动旋翼引流的有利干扰下升力系数提高了35%。     

钛合金转子叶片系列焊机的研制及应用

针对各种新型航空发动机钛合金转子叶片阻尼台毗邻面耐磨性提高的迫切需求,研制成功JQGP-80型系列真空充氩高频感应钎焊设备,结合国产化材料及焊接工艺的全面突破,解决了钛合金叶片阻尼凸台磨损问题,为多种重点型号研制的顺利进行提供了强有力的硬件保障。     

考虑重力的风机叶片水平加载测试方法

在风电叶片三维有限元参数模型中引入了重力产生的附加载荷,仿真计算了风电叶片水平加载方式的静载荷测试中附加载荷产生的水平方向的耦合位移,分析了耦合位移对测试过程中理论计算结果的影响;由于重力的叠加效应,测试中某些截面实际施加的等效载荷可能远超叶片设计的目标测试载荷,建议联合有限元分析,优化叶片安装角度和加载力方向的方法,降低叶片局部截面实际施加等效载荷的过载峰值。     

基于叶尖定时的叶片耦合振动参数辨识与仿真

为了实时掌握叶片振动情况、预防故障发生,目前最常用的非接触振动测量方法是基于单自由度模型的叶尖定时法,但当叶片耦合振动时2个振动峰相隔很近,该方法无法同时识别出其振动参数。采用基于2自由度模型的曲线拟合方法,得到叶片耦合振动2个峰的初始相位等参数,用相位遍历法辨识出叶片的振动阶次和频率。结果表明:采用基于2自由度模型的曲线拟合方法提高了叶片耦合振动参数辨识的精度,辨识了相邻2个峰的振动参数。辨识振动与仿真参数设置基本一致。     

热障涂层技术在航空发动机涡轮叶片上的应用

热障涂层是提高航空发动机涡轮叶片工作温度的有效途径之一。根据某型发动机高压涡轮工作叶片、导向器叶片的结构特点和各种涂层制备技术的优缺点,制定了工作叶片和导向叶片表面底层、面层和内腔的涂层制备方案。对工作叶片、导向器叶片材料试样表面涂层的性能开展一系列测试试验。结果表明:涂层性能满足要求,涂层制备方案合理可行;对工作叶片、导向器叶片内表面涂层的厚度,气膜孔径的影响以及质量增加情况进行测量分析,结果均满足设计要求,表明涂层制备工艺合理可行。     

直升机旋翼标准桨叶的选定原则与方法研究

本文对直升机桨叶单片互换的原理进行了论述，对标准桨叶的确定原则以及实施方法进行了探讨，并结合直11型机标准桨叶选定工作的流程和结果，对所述方法进行了实例分析。