工艺模型驱动的物料动态精准配送技术

针对飞机装配车间传统“领料式”物料配送存在的弊端,提出了一种工艺模型驱动的物料动态精准配送方法,构建了飞机装配车间物料精准配送管理系统,阐述了系统构建涉及的关键技术难点,采用基于模型的三维可视化消耗式BOM重构方式,建立与设计了模型动态同步精准的MBOM工艺模型,利用RFID技术的优点实时获取物料信息,通过iGPS系统引导AGV物料运输平台来实现装配站位物料的高精度配送。     

深空探测中多普勒的建模与应用

针对深空探测中的多普勒观测资料的单程和三程模式,分别给出了瞬时和积分的观测模型,双程多普勒观测模型是三程模式的一个特殊情况.通过比较瞬时和积分多普勒的差异,推断在积分周期取得足够小时,瞬时观测模型与积分模型是一致的.利用2009年8月份对火星探测器MEX的三程多普勒测轨资料的处理,检验了三程多普勒资料观测模型的正确性,利用约一个圈次8小时三程多普勒数据进行轨道计算,定轨结果与欧空局重建轨道位置差约几百米.     

基于Pro/E软件的卫星三维建模方法的探讨

主要对基于Pro/E软件的卫星三维建模和高效率、高可靠性、低成本的总装设计方法等进行了初步的研究和探讨。     

Theoretical modeling of vectoring dual synthetic jet based on regression analysis

The excellent vectoring characteristic of Dual Synthetic Jet (DSJ) provides a new control strategy for the active flow control, such as thrust vectoring control, large area cooling, separated flow control and so on. For incompressible flow, the influence relation of source variables, such as structure parameters of actuators, driving parameters and material attributes of piezoelectric vibrating diaphragm, on the vectoring DSJ and a theoretical model are established based on theoretical and regression analysis, which are all verified by numerical simulations. The two synthetic jets can be deemed as a main flow with a higher jet velocity and a disturbing flow with a lower jet velocity. The results indicate that the influence factors contain the low-pressure area formed at the exit of the disturbing flow, which could promote the vectoring deflection, and the impact effect of the disturbing flow and the suppressive effect of the main flow with the effect of restraining the vectoring deflection. The vectoring angle is a complex parameter coupled by all source variables. The detailed theoretical model, whose error is controlled within 3.6 degrees, can be used to quantitatively assess the vectoring feature of DSJ and thus to provide a guidance for designing the control law applied in the active flow control.     

New constitutive relation for eddy viscosity models

A new turbulent constitutive relation was directly derived from Boussinesq's hypothesis and mixing length theory, and then implemented in the standard k-ε model. The performance of this constitutive relation was validated in zero pressure gradient flat-plate boundary layer flow, fully-developed turbulent channel flow and separated flow in a plane asymmetric diffuser. The investigation demonstrated that, this new constitutive relation gave very accurate results in the former two basic cases and provided significant improvement in prediction of separated and reattachment points in the plane asymmetric diffuser. Separation and reattachment points at x/H=7.5 and 29 were calculated accurately in comparison to experimental results, and the static pressure coefficient of 0.82 was very close to large eddy simulation calculation. These results are very encouraging but further verification and extensive application of the new constitutive relation to other two-equation eddy viscosity model are needed.      

30P-30N多段翼型复杂流场数值模拟技术研究

采用"亚跨超CFD软件平台"(TRIP2.0)数值模拟了30P-30N多段翼型的复杂流场,主要目的是考核湍流模型、转捩位置对多段翼型压力分布和典型站位速度型的影响。本文通过求解任意坐标系下的雷诺平均的N-S方程,采用多块对接结构网格技术,在与相应试验结果对比的基础上,详细研究了SA一方程湍流模型、SST两方程湍流模型、不同的转捩位置对该翼型压力分布和典型站位速度型的影响。本文的研究结果表明,采用全湍流模拟方式可以较好地模拟该多段翼型的压力分布,但对速度型的模拟精度较差;模拟试验的转捩位置可以改善主翼附面层与前缘缝翼边界层尾迹区的模拟精度;采用微吸气技术推迟前缘缝翼的转捩位置,可以进一步提高缝翼尾迹区的数值模拟精度。     

面向代理模型的机翼变形计算方法

按照机翼结构设计的原则,对内部结构还未确定的机翼提出了一种通用的变形计算方法。机翼的平面形状可看作由多个梯形组成,机翼弯曲变形为三次函数,扭转变形为一次函数。只要给定翼梢挠度与扭转角,即可计算机翼变形情况下的几何模型,使代理模型能够预测变形后机翼的气动载荷分布。文中给出了两个实际机翼的算例。算例结果表明,本文模型预测的变形与实际结构有限元分析给出的变形吻合较好。     

高精度GPS定位的精密电离层模型

在长距离GPS实时动态定位(RTK)过程中,电离层延迟误差是影响定位精度的主要误差源.目前,由于采用全空间电离层模型精度不够,对长距离RTK定位主要采用双差电离层残差内插方式.本文提出一种新的电离层模型.该模型仅对每个卫星轨迹通过的电离层部分进行建模,可适用于高精度GPS定位.采用香港数据,结果表明,该模型可较好地模拟低纬度电离层变化,并可支持GPS厘米级定位精度.     

浅析航材承修商多维度管理

在深航近年来使用的承修商管理模式的基础上,通过实践不断修正,新增可视化质量评估平台,使深航的承修商管理形成一个完整的闭环监控,本文对这一可视化质量评估模型进行了详细介绍,以期为业内航材承修商管理工作提供参考。     

2.5维机织复杂结构件的静强度

采用宏细观结合方法,针对经纱和纬纱等材料组分可能发生的多种失效模式,分别建立了基于改进的Hashin准则的系统性的材料失效准则及不同失效模式下的刚度退化模型.引入逐渐损伤的思想,建立了2.5维机织复杂结构件静强度系统性分析方法.模拟并分析了材料经向拉伸和纬向拉伸的应力-应变曲线,与实验得到的材料应力-应变曲线相比,相同应变下应力误差不超过6.5%,具有较好的重合度;对2.5维机织压气机静子连接结构模拟件开展了逐渐损伤模拟,结果表明:结构损伤主要集中在叶根倒角附近,其中吸力面叶根处的基体压缩失效形式会引起结构大幅变形,是结构破坏的主要原因.