基于决策树的涡轴发动机气路健康评估方法

为解决涡轴发动机退化模式多、故障样本大、分类困难的问题,将梯度提升决策树(GB?DT)算法应用于涡轴发动机气路健康评估.首先对涡轴发动机故障标签进行了拆解,针对每一类标签设计了一个分类器.通过特征重要度排序筛选了6个分类标签的输入特征,有效降低模型复杂度.通过遍历确定树的最优数量和深度,确保了分类的准确性.仿真结果表明...     

预冷却涡轮基组合循环发动机发展现状及应用前景

本文介绍了国外新型预冷却涡轮基组合循环（TBCC)发动机的技术研究现状,其中最具代表性的是美国的喷流预冷却TBCC发动机和日本的ATREX发动机。在对预冷却TBCC发动机发展现状分析的基础上,介绍了预冷却TBCC发动机的技术优势、关键技术、潜在应用方向及我国开展预冷却TBCC发动机研究的可行性。     

某型涡扇发动机热起动性能故障分析与调整研究

本文针对国内翻修后的某型涡扇发动机起动性能有所下降,造成外场在炎热天气下使用时起动困难的问题进行原因分析和调整研究.     

直连式喷气发动机试车台试验件进气的联接方式及有关问题

针对直连式喷气发动机试车台稳定段同试验件的联接问题，根据空气流量测量、补氧及推力测量等不同试验目的与要求，讨论了选择联接方案对试验结果的影响。结果认为，模拟总温较高时，音速喷嘴流量测量联接方式应慎重选用；采用能够测量进、出口压力的迷宫密封方式，可以根据喷嘴及回绕式阻隔件流动理论计算出空气泄漏量并可测出压力损失值，从而对试验所要求的补氧量及推力测量提供较准确的修正。     

单组元300N发动机低温试验研究

为探究低温环境下单组元300N发动机的工作特性,揭示影响发动机低温性能的主要影响因素,以300N发动机为试验对象,开展了模拟飞行工况的发动机低温试验。给出了低温试验研究方法,分别从温度差异对发动机性能影响、催化剂活性差异对发动机低温启动特性影响和低温对电磁阀响应特性影响等方面获得研究结果。结果表明,低温是影响发动机低温性能的主要影响因素,-48℃条件催化剂无法完成推进剂的催化分解,发动机发生爆炸;-30℃条件下起活时间为80.5～87.5ms,发动机可正常启动,且启动温度与起活时间呈指数关系;催化剂批次差异也对发动机低温工作性能产生一定影响,不同批次催化剂低温起活时间的差异可达91ms;低温试验过程中,电磁阀的关闭受到低温推进剂粘性和背压的影响,产生了明显的迟滞现象,延迟时间约100ms,对发动机在轨的精准控制存在一定影响。     

射线计算机成像技术在发动机变壁厚产品检测中的试验研究

针对液体火箭发动机离心轮、涡轮静子等厚度变化大的复杂激光选区熔化成形（SLM）钢构件在常规X射线胶片照相检测（RT）时,由于胶片的宽容度低造成的检测覆盖率低,存在漏检质量隐患的问题,采用射线计算机成像技术（CR）对该类变截面厚度差在5～20 mm内的钢构件进行检测。结果表明,CR检测图像宽容度是胶片照相检测的3倍,检测覆盖率高;以离心轮线状缺陷CR检测为例,且通过CT和理化检测验证证明,CR检测具有与胶片照相检测基本一致的缺陷检测灵敏度、可靠性。     

小型弹用涡轮发动机发展综述

小型涡轮喷气和涡轮风扇发动机可为高亚音速、中远程导弹提供理想的巡航动力,是各军事强国竞争的焦点。弹用涡轮发动机具有成本低、寿命短、尺寸小、转速高、增压比低、容积热强度大、起动和点火方式多样等特点,已被广泛应用于巡航、反舰和空地等多种战略与战术导弹。从国内外主要产品及其技术参数、性能与结构基本特点、应用现状、发展趋势等方面,对20世纪70年代以来100~700daN推力范围内弹用涡轮发动机的发展情况进行梳理和分析。指出更低成本、更少油耗和更优结构将是未来导弹推进系统继续追求的目标;螺桨风扇发动机高速性好、耗油率低,脉冲爆震涡轮发动机循环效率高、结构简单,是未来先进弹用涡轮发动机重要的发展方向。     

基于轮毂电机的电动汽车再生制动研究

基于轮毂电机驱动的电动汽车的结构特点以及轮毂电机低转速、高转矩的特点,提出了轮毂电机再生制动方法。 为了恢复最大制动能量,在中等强度制动条件下通过轮内电机输出车辆减速的所有制动转矩。 由AMESim软件建立液压制动系统和轮毂电机驱动系统的车辆动力学模型。 通过NEDC循环和FTP75循环对车辆驾驶条件进行了仿真。仿真结果表明:采用轮内电机制动方式,制动能量回收率显著提高,电动车的能源效率提高30%以上。     

Periodic atomization characteristics of an impinging jet injector element modulated by Klystron effect

An experimental study on the Klystron effect of periodic injection modulated by pressure drop fluctuations on subsequent atomization is conducted. Time-resolved atomization backlit images and atomization Mie scatter images are captured by using the high speed camera. It is found that periodicity of forced atomization relies on pressure drop fluctuation amplitude and phase differences between atomization and pressure drop fluctuations relate to fluctuation frequencies. This feature of periodic atomization induced by Klystron effect corresponds to periodicities and high amplitudes of pressure fluctuations in unstable combustion chambers and chaos and low amplitudes of pressure fluctuations in stable combustions chambers. Drastically periodic varying of gross surface area of droplets with time was shown in Mie scatter images. The importance of periodic impinging jet atomization modulated by pressure drop fluctuations for acoustic liquid propellant combustion instabilities is illustrated.     

A novel integrated self-powered brake system for more electric aircraft

Traditional hydraulic brake systems require a complex system of pipelines between an aircraft engine driven pump (EDP) and brake actuators, which increases the weight of the aircraft and may even cause serious vibration and leakage problems. In order to improve the reliability and safety of more electric aircraft (MEA), this paper proposes a new integrated self-powered brake system (ISBS) for MEA. It uses a hydraulic pump geared to the main wheel to recover a small part of the kinetic energy of a landing aircraft. The recovered energy then serves as the hydraulic power supply for brake actuators. It does not require additional hydraulic source, thus removing the pipelines between an EDP and brake actuators. In addition, its self-powered characteristic makes it possible to brake as usual even in an emergency situation when the airborne power is lost. This paper introduces the working principle of the ISBS and presents a prototype. The mathematical models of a taxiing aircraft and the ISBS are established. A feedback linearization control algorithm is designed to fulfill the anti-skid control. Simulations are carried out to verify the feasibility of the ISBS, and experiments are conducted on a ground inertia brake test bench. The ISBS presents a good performance and provides a new potential solution in the field of brake systems for MEA.