碳纤维复合材料高压球形容器研制

采用变带距方法对球形容器进行优化设计，并研制了一批产品。试验结果表明，在纤维设计应力相同条件下，采用变带距缠绕的球形容器，其复合材料重量比等带距缠绕的轻２４．５６％，而其容器特性系数高出１０．４％，能同时满足设计提出的强度和重量两方面要求。     

2D碳/碳复合材料CVI过程的数值模拟研究

本文根据３Ｄ碳／碳复合材料的结构特征及ＣＶＩ工艺的特点建立了孔隙模型和动力学模型，并利用该模型对其ＣＶＩ过程进行了模拟与分析。模拟结果与实验结果的对比表明该数学模型是合理的。     

Tether Satellite System Collision Study

A study was performed to determine the probability of collision with resident space objects and untrackable debris for the tether component of the Tethered Satellite System (TSS) after it broke away from the Space Shuttle orbiter (mission STS-75) in February 1996. Both an analytical and a numerical approach were used in this study, and the results obtained with these two methods were found to be in good agreement. These results show that the deployed tether is expected to have been impacted by several particles 0.1mm or larger in size. The probability of collision with objects 10cm in size or larger was on the order of 10^–3 per month. Since the severed tether reentered within one month after deployment, the collision hazard to other objects while in orbit was small. The analytical methods used in this study are useful for tether collision evaluations in general.     

带滑移铰空间机械臂惯性空间轨迹的复合自适应跟踪控制

讨论了载体的位置与姿态均不受控制的漂浮基带滑移铰空间机械臂的控制问题。动力学分析表明，结合系统动量及动量矩守恒关系得到的运动Jacobi关系及系统动力学方程将是系统惯性参数的非线性函数，借助于增广变量法，我们得到了与惯性参数呈线性关系的系统广义Jacobi矩阵及系统控制方程，以此为基础，针对系统中存在未知惯性参数的情况，设计了一种末端抓手惯性空间期望轨迹跟踪的复合自适应控制方案，此控制方案的优点在于不需要测量空间机械臂载体的位置及移动的速度，加速度，仿真运算证实了方法的有效性。     

太阳风质子束流的演化

太阳神飞船观测表明，太阳风高速流中质子束分量相对于核分量的密度随日心距离增加而增加．提出解释这一观测现象的机理并给出二维数值模拟结果．由于阿尔芬波速随日心距离增加而减少，第二支左旋波将与更多的质子共振，把部分原来属于核分布的质子拉到束分布中来．用数值模拟方程方法求解回旋波共振导致的准线性扩散方程，数值结果与观测结果相符合．     

地磁急始年发生数周期特征的小波分析

采用小波分析方法分析了急始年发生数的时间序列的周期特征，并对急始发生数的特征与太阳黑子相对数的特征进行了简要的对照分析，分析结果表明，急始发生数的周期规律与太阳黑子相对数的周期规律是有差异的．还进行了太阳黑子相对数与急始数的相关性，太阳黑子相对数与急始磁暴的相关性研究，分析结果表明它们之间显著相关．还对急始数与急始磁暴致以及其他的一些参数之间的相关性进行了分析，最后对分析结果进行了讨论．     

复合材料梁的热弯实验

为研制先进的导弹弹翼，用新研制的复合材料制成工字梁，模拟导弹飞行时翼梁受热弯条件进行实验，测出梁的温度和挠度随时间变化曲线，确定正常使用条件和失效形式，用此复合材料代替现役导弹的金属材料，可明显减重，改善性能。     

某机种复合材料构件的模态分析

 <正> 对某机种碳纤维复合材料垂尾加强肋、座舱盖、垂尾蒙皮等构件进行模态分析试验,所采用的试验方法如图1所示。     

搅拌铸造金属基复合材料铸锭的气孔率

阐述了降低气孔率是搅拌铸造工艺制备颗粒增强型金属基复合材料的关键技术。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.