侧向喷流的一种直接实验模拟

研究了侧向喷流的一种直接实验模拟技术,旨在探讨喷流力直接作用在天平上时,侧向喷流对气动载荷的影响及其增益情况。本文的直接模拟是通过一种通气式应变天平实现的。研究中分析了有关模拟原则,妥善处理了诸如高压气体密封、天平变形引发的漂移、干扰等相关技术问题,并在一尖拱柱构型上实现了多种条件下的直接模拟,给出了来流条件和喷口参数条件对法向力、俯仰力矩增益因子的影响。最后,就实验结果进行了适当讨论和评述。     

炮风洞中进行高温喷流底部热流、压力测量试验

本文介绍了在北京空气动力研究所炮风洞 M 数为6、7、8的气流中进行具有高温喷流的模型底部热流和压力测量试验的有关试验技术。试验结果表明底部对流热流和压力测量值随外流 M 数增大而减小,他们都大于无外流时的测值。辐射热流不受外流影响。     

喷流噪声特性与控制研究

本文着重研究喷流噪声机理及工程计算方法。通过实验研究了声功率与喷流速度的关系,表明在Mα>0.4时Lighthill方程和Lilley方程均与实验数据吻合,可分别使用。而Mα<0.4时,均偏差较大,通过本文实验表明,若改为6次方关系较为恰当。文章同时对喷流噪声指向性、谱特性进行了分析。最后对一种引射消声器进行了发展性研究,获得在135dB噪声条件下,降噪17dB的效果。     

喷管扩张段烧蚀的“台阶效应”计算

当喉衬和扩张段内衬采用具有不同烧蚀率的材料时,常出现“台阶效应”.本文以气动热化学烧蚀机理为基楚,提出应用适当的对流换热和加剧的化学反应计算对台阶效应区进行修正的方法,使台阶效应区的烧蚀率预示更切合实际工况.     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

基于微型涡喷发动机热喷流的无源流体推力矢量喷管的控制规律

流体推力矢量喷管型面固定、活动部件少、结构重量轻，能够为高机动飞行器提供有效的飞行控制手段，但无源流体推力矢量喷管热喷流的偏转控制规律尚未完全掌握。为了推进无源流体推力矢量技术的实用化，本文设计研制了适用于微型涡喷发动机的耐高温喷管模型，对该喷管在微型涡喷发动机热喷流状态下的控制规律进行研究。利用非接触光学显示和测量手段——红外热成像拍摄和粒子图像测速（PIV）技术对主射流流动特性进行研究，获得流动矢量角随二次流控制阀门闭合度变化的控制规律；利用六分量盒式天平测力实验研究无源流体推力矢量喷管的力学特性，获得推力矢量角随二次流控制阀门闭合度变化的控制规律。研究结果表明：该构型喷管在微型涡喷发动机热喷流下主射流连续可控偏转，最大流动矢量角为-12.3°/12.3°，最大推力矢量角为-12.9°/12.8°，控制规律接近线性，不存在主射流偏转突跳问题。     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

某发动机调节器自动检测异常故障分析

针对某型发动机自动调节器自动检测异常的故障现象,对产生发动机自动调节器自动检测异常的原因进行了深入地研究分析,并提出了针对性的预防措施。     

浅谈水洗发动机对大修成本的影响

通过对深圳航空公司CFM56-7B发动机水洗方法改进前后的发动机进厂大修数据进行比较,主要分析HPT导向器报废率的变化,说明改进的发动机水洗方式对于延长发动机在翼时间、降低HPT导向器报废率、节约大修成本起到良好促进作用。     

军用飞机型号研制试飞费用估算研究

在借鉴国外经验的基础上,对国内军用飞机型号研制试飞费用的构成进行了研究,提出基于兰德DAPCA IV模型的军用飞机型号研制试飞费用估算模型,为试飞费用的估算提供了依据。