基于碳纳米管薄膜的复合材料层间增韧

通过浮动催化化学气相沉积法制备连续碳纳米管薄膜,并将其原位沉积到单向碳纤维织物表面,手工铺层后借助真空辅助树脂传递模塑成型（VARTM）工艺制备碳纳米管-碳纤维/环氧树脂复合材料层压板,研究不同面密度的碳纳米管薄膜对层压板Ⅱ型层间断裂韧性的影响。结果表明,随着碳纳米管薄膜面密度的增加,层压板Ⅱ型层间断裂韧性先逐渐提高,当碳纳米管薄膜面密度为9.64 g/m²时,层压板Ⅱ型层间断裂韧性最佳,与原始层压板相比提高了94%。碳纳米管通过桥接树脂裂纹、从树脂中拔出等方式提高层间断裂韧性。当碳纳米管面密度超过临界值时,会引起树脂浸润困难,导致增韧效果降低。     

激光功率与底面状态对选区激光熔化球化的影响

为研究激光功率与底面状态对选区激光熔化熔池流动的影响,基于离散单元法建立了选区激光熔化铺粉模型,采用粒径分布与实验相符的马氏体时效钢粉末分别铺展到平坦底面和增材底面上,将计算获得的粉末分布导入到基于有限体积法建立的选区激光熔化熔池计算流体力学模型中,研究激光功率和基板底面粗糙度对熔池流动和熔道表面形貌的影响。采用激光单道扫描实验验证铺粉模型和选区激光熔化模型。结果表明：随着激光功率的降低,单位长度的球化数量增加;由于增材底面使熔池润湿性变差,同时又对熔池流动行为产生扰动,使得增材粗糙底面上熔道的球化数量增加。选区激光熔化铺粉模拟及激光单道扫描模拟结果与实验结果吻合较好。本研究可为选区激光熔化工艺中工艺参数的选择提供理论指导。     

POD和DMD方法分析不同间隙压气机旋转不稳定性特性

对一台单级低速轴流压气机旋转不稳定性(RI)进行分析。在前期的旋转不稳定性特性、流场成因和不同间隙影响的研究基础上,进一步基于全通道数值模拟,采用两种流场降阶方法分析不同叶顶间隙条件下旋转不稳定性各阶模态对应的流场成分、模态能量占比和稳定性等特性。计算结果表明,前几阶模态能量占比大,对流场起主要贡献,并且稳定性相对较强。随着间隙的减小,旋转不稳定性的能量占比和稳定性下降,各阶的叶片转动成为流场的主要成分。      

变频电动机耦合电容分析与计算研究

脉宽调制(PWM)变频驱动器在提高交流传动系统效率的同时,产生的高次谐波导致共模电流显著增加。其中电动机定子绕组与定子铁心之间的耦合电容是共模电流的主要通路。准确计算定子绕组与定子铁心之间的耦合电容对于预测共模电流具有重要意义。由于电机绕组内部导线排列不规则,准确进行解析计算较为困难,将其简化为集中导体后,会导致计算精度变差。在绕组全散线模型的基础上,提出了一种简化散线建模方法,能在计算精度不变的情况下,有效地减小模型的复杂度。通过对比解析计算、全散线模型、简化散线模型和测量值,验证了该方法的有效性。     

一种开关磁阻电机无位置传感器控制效率优化策略

针对开关磁阻电机(SRM)的简化磁链法只能实现单相导通运行且导通区间固定的缺点,提出了一种结合固定关断角和自适应调节开通角的无位置传感器控制技术。利用曲线拟合关断位置磁链取代传统存储数据表,通过对比实时计算的动态磁链和曲线拟合的静态磁链,确定关断位置信号并估计转速和其他位置。考虑电机阻抗和电感的非线性特点,优化电感最小区域的开通角自调节模型确定导通区间。仿真结果验证了该方案的可行性和正确性,能够实现转子位置的间接检测,电机的运行效率得到进一步优化。     

基于超螺旋二阶滑模的双馈风力发电机控制策略

传统双馈风力发电机(DFIG)控制存在抖振现象,容易造成系统的不稳定。为了减轻控制抖振现象,提高控制的稳定性,在分析了DFIG动态特性的基础上,建立了DFIG的数学模型,设计了超螺旋二阶滑模控制器,并研究了突变风的情况下滑模控制器的控制性能。通过MATLAB/Simulink工具进行了仿真验证。仿真结果证明:滑模控制器具有良好的最优转矩跟踪能力和无功调节能力,与一般的控制方法相比鲁棒性较强,转子控制电压连续,控制产生的抖振可以大幅减轻,系统的稳定性大大提升。     

基于二阶滑模算法的永磁电机直接转矩控制

针对传统直接转矩控制(DTC)方法低速控制精度差、转矩脉动大、开关频率不稳定等问题,提出了一种基于二阶滑模控制的永磁电机DTC方法。该控制方法基于二阶滑模控制原理,将传统磁链控制器与转矩控制器以滑模控制器替代,对空间电压进行矢量调制,提高了开关频率的稳定性,获得了良好的动态稳定性,改善了电机输出性能。仿真与试验结果表明,该控制方法能够有效减小电流脉动与转矩脉动,同时提高了控制系统的抗干扰能力,实现了电机的快速动态响应,具有较强的鲁棒性能。     

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

High-fidelity trajectory optimization for aeroassisted vehicles using variable order pseudospectral method

In this study, the problem of time-optimal reconnaissance trajectory design for the aeroassisted vehicle is considered. Different from most works reported previously, we explore the feasibility of applying a high-order aeroassisted vehicle dynamic model to plan the optimal flight trajectory such that the gap between the simulated model and the real system can be narrowed. A highly-constrained optimal control model containing six-degree-of-freedom vehicle dynamics is established. To solve the formulated high-order trajectory planning model, a pipelined optimization strategy is illustrated. This approach is based on the variable order Radau pseudospectral method, indicating that the mesh grid used for discretizing the continuous system experiences several adaption iterations. Utilization of such a strategy can potentially smooth the flight trajectory and improve the algorithm convergence ability. Numerical simulations are reported to demonstrate some key features of the optimized flight trajectory. A number of comparative studies are also provided to verify the effectiveness of the applied method as well as the high-order trajectory planning model.     

涡轮盘多轴低循环疲劳寿命可靠性分析

多轴低循环疲劳是航空发动机涡轮盘的主要失效模式,应用多轴疲劳寿命预测的等效应变模型和临界面模型对某涡轮盘中心孔的疲劳寿命进行了预测,并与试验寿命进行了对比,得出等效应变模型预测结果均偏于危险,并且误差较大,而临界面模型误差较小,尤其拉伸型破坏的SWT模型误差在10%以内。进一步选取SWT模型进行了涡轮盘的寿命可靠性分析,鉴于多轴疲劳试验复杂、费用高并缺少统计数据,利用现有单轴疲劳试验数据将疲劳性能参数表示为标准正态随机变量的函数,将SWT模型随机化建立多轴疲劳寿命概率模型,得到可靠度0.998 7的涡轮盘寿命,与试验估计给出的技术寿命较为接近。