高空高速无人飞行器热控制系统设计

针对飞行时间短、速度和高度变化快、表面温度波动大的无人飞行器UAV(Unmanned Aerial Vehicles)热控制系统设计难题,提出了一种可解决实际工程问题的热分析计算方法.即把热天工况、冷天工况和标准天工况作为设计/试验工况;采用参考温度法、高超音速工程预测法或计算流体动力学CFD(Computational Fluid Dynamics)数值模拟法,确定了飞行器表面温度分布,并把其作为后续热分析数学模型的外边界条件;分析结构热容量对瞬态热载荷的影响,建立与之相应的边值问题方程,并采用有限差分法求解;根据高空高速飞行特点及瞬态热载荷值,确定仪器设备舱调温系统方案.     

飞机V型外倾双垂尾载荷校准技术

根据垂尾载荷校准及建模需求,对飞机V型外倾双垂尾结构受载情况进行了分析和简化,确定了校准试验载荷,研制了垂尾载荷校准试验专用龙门梁架。采用液压协调加载技术,完成了外倾双垂尾载荷校准试验,建立了满足测载要求的载荷模型。此种方法充分利用了左右垂尾外倾、双垂尾之间空间较大的特点,对左右垂尾对称施加向外的单点、多点载荷,加载载荷侧向分量左右自平衡,垂向分量依靠飞机自身重量即可平衡,飞机不需要复杂的固定与约束。试验中采用先搭建龙门框架,再停放飞机的方法,降低了试验风险、加快了试验进度,取得了良好的试验结果,对其他此类结构的载荷校准具有一定的借鉴作用。     

基于脑电功率谱密度的作业人员脑力负荷评估方法

脑力负荷状态的准确识别对减少因作业人员无效脑力负荷导致的人因事故具有重要意义。针对人-机系统中作业人员脑力负荷客观评估问题开展了基于MATB-Ⅱ平台的3种不同脑力负荷水平下的航空情境实验，记录16名被试的NASA任务负荷指数（NASA-TLX）量表数据和脑电（EEG）信号，提出了一种基于脑电功率谱密度（PSD）和支持向量机（SVM）的个体脑力负荷评估方法。结果表明：随着实验设计脑力负荷水平增加，被试的主观脑力负荷得分显著提高（p<0.001），这表明该实验任务设计较好地诱发了低负荷、中负荷和高负荷情境。在此基础上，通过网格搜索法确定个体脑力负荷评估模型的统一优化参数，惩罚系数取3 000，核函数参数取0.000 1，模型测试正确率达到0.966 5±0.029 8，宏平均的受试者工作特征曲线下的面积（Macro-AUC）达到0.991 0±0.011 4。本文为作业人员脑力负荷状态的客观和准确评估提供了一种新的办法，为后期作业人员脑力负荷状态的实时判别提供模型基础。     

Application of improved active disturbance rejection control algorithm in tilt quad rotor

The Tilt Quad Rotor (TQR) has complex dynamics characteristics, especially in conversion mode. It is difficult to build the dynamic model of the TQR and the environmental factors have a great influence on it. To solve the problem of control in conversion mode of TQR, this paper carries out the design of the controller based on improved Active Disturbance Rejection Control (ADRC). According to the characteristics of flight in conversion mode, Tracking Differentiator (TD) with explicit model is used to solve the problem of multiple integrals when the system is high-order system. Extended State Observer (ESO) with Radial Basis Function (RBF) neural network is used to estimate and compensate for internal and external uncertainties, and the adaptive sliding mode control in Nonlinear State Error Feedback (NLSEF) is used to improve the response speed of the controller and reduce the parameters which should be tuned. Through the flight control simulation of the TQR, the validity and rationality of the control system are verified.     

A comprehensive study of the 2016 Mw 6.0 Italy earthquake based on high-rate (10 Hz) GPS data

The 2016 M_w 6.0 Italy earthquake is successfully recorded by the near-field 10?Hz GPS and 200?Hz Strong Motion (SM) stations, providing valuable data for this study. A comprehensive study of this earthquake is carried out based on GPS data, which contains coseismic deformations analysis, noise analysis, seismic wave picking, and magnitude determination. The noise of most GPS-derived displacement waveforms can be described as a combination of white noise, flicker noise, and random walk noise after the earthquake occurrence, and the spectral indices vary significantly for most stations, implying that the seismic signals have affected the noise characteristic of GPS-derived displacement waveforms. S-transform is employed to assess the GPS capability to detect the seismic arrival time. The SM station AMT and the GPS station AMAT are in good agreement in seismic wave picking, and the difference is only 1.2?s in the north component, suggesting that the outcome of seismic wave picking using GPS data is reliable. Then, a classic empirical formula is employed to determine the moment magnitude. A robust moment magnitude (Mw 5.90) can be estimated by the nine GPS stations with about 23.9?s. If four GPS stations near the epicenter is chosen to determine the magnitude, it only take 13.0?s to retrieve a reliable preliminary (Mw 5.82) magnitude, which is 5.4?s ahead of nine stations. In addition, Cross Wavelet Transform (XWT) is adopted to measuring the correlation and phase relationship between GPS and SM records. The result of XWT analysis indicates 10?Hz GPS is capable of capturing reliable and accurate coseismic dynamic deformations, as evidenced by the XWT-based semblance being close to 1 between GPS and SM records. The above results confirm the capability of 10?Hz GPS to capture coseismic dynamic deformations, detect seismic arrival time, and determine earthquake magnitude. Moreover, rapid magnitude determination based on 10?Hz GPS data can be regarded as an important supplement to Earthquake Early Warning (EEW).     

飞机附件的维修间隔决策

研究了飞机附件软时限的设定和管理方法,该方法可将附件的故障发生机率和运行风险控制在可接受水平,减少航空公司因机务原因的延误,提高飞机可利用率。     

双框架飞机蒙皮检测机器人切换运动控制方法

针对一种双框架飞机蒙皮检测机器人,通过分析该机器人在飞机表面上的受力情况,在飞机表面该机器人受到了非完整约束,基于牛顿-欧拉法建立了机器人非完整约束动力学模型。根据机器人机械结构和运动步态分析,将该非完整机器人系统分为子系统A和子系统B。为了实现机器人在飞机表面运动,采用反演技术和快速Terminal滑模控制相结合的思想对系统设计了控制器,提出了一种反演-滑模控制方法;对于非完整机器人子系统A和子系统B,设计了一种基于事件驱动的切换策略,实现了机器人对期望轨迹的全局渐近跟踪,并利用Lyapunov稳定性证明系统的跟踪误差收敛。仿真和试验表明,采用该切换策略和反演-滑模控制方法,双框架飞机蒙皮检测机器人可以在飞机表面自由运动并进行损伤检测,具有良好的可靠性和稳定性。     

基于Visual Basic的互感器负荷箱测量仪校准系统的实现

为解决互感器负荷箱测量仪同相分量和正交分量的校准问题,在分析互感器负荷箱测量仪工作原理的基础上,设计了基于电子/电工组合式的互感器负荷箱测量仪校准装置,并简要说明装置电工部分、电子部分以及上位机软件的实现。经省级计量研究院验证结果表明,该装置校准结果符合0.2级要求,可作为标准装置解决1级互感器负荷箱测量仪量值溯源问题。     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.