40CrNi2Si2MoVA钢喷丸强化层微观结构

喷丸强化在金属材料表面形成强化层,可以有效提高构件的疲劳寿命,是金属构件表面完整性制造的重要方法.喷丸强化已有效应用于40CrNi2Si2MoVA钢制构件,为了探明喷丸强化对该钢种的强化机理,本工作采用高分辨电子显微电镜(HREM)对40CrNi2Si2MoVA钢喷丸强化层微观组织结构进行了系统分析研究.结果表明:喷丸强化使40CrNi2Si2 MoVA钢组织细化,呈明显的马氏体“有效晶粒”现象,“有效晶粒”尺寸为几个纳米到几十个纳米;“有效晶粒”界面呈明显的倾转现象,相邻“有效晶粒”间转动角度为几度到几十度,最大达到30°.     

锻造温度对TC4合金组织与性能的影响

研究锻造加热温度对TC4合金组织与性能的影响规律。表明其均采用锻后水冷加强化热处理相同条件下,TC4合金采用高温锻造(相变点以下10℃至相变点以上5℃),可以获得细密交错的网状α+β组织,或其间伴有少量等轴α相的双态组织,从而可得到高强度与高塑性的性能。本文还讨论了上述工艺使TC4合金有效强化的机理。     

淬火制度对16NiCo钢组织性能的影响

研究了淬火温度及冷却方式对１６ＮｉＣｏ钢微观组织和性能的影响，结果表明：该钢不同温度淬火风冷与油冷后，随淬火温度的提高，性能变化趋势相近，强度至８００℃～８３０℃达最大值，而后开始降低，８６０℃淬火冲击韧性为最高。８６０℃油淬与８３０℃风冷相比，强度下降不多，冲击韧性提高幅度比较大，并且随淬火温度的增加，两个强度指标之间的差别越来越大。     

基于Deform软件二次开发和BP神经网络的TA15多向锻造微观组织预报

通过热压缩实验构建了TA15合金的热变形真应力-应变曲线,以此为基础分别建立了合金双相区及单相区温度区间的热变形本构方程;基于热压缩试样动态再结晶的统计数据建立了TA15合金的动态再结晶模型。借助Deform提供的二次开发功能实现相关数学模型的程序化,制定正交实验方案,实现了TA15合金多向锻造变形的微观组织仿真。通过正交实验分析得出各项因子的影响对象及强弱差异,提出了双相区及单相区温度区间内的多向锻造最佳因子组合。建立了TA15合金多向锻造变形微观组织的BP （Back Propagation）神经网络预测模型,将预测结果与有限元仿真结果进行比较,结果表明两种方法的预测结果基本一致,但神经网络具备有限元仿真难以实现的良好细节预测能力,能更为细致地实现对微观组织分布状态的划分。     

厚度和环境对复合涂层导电性能的影响

为了给数字化刻铣曲面频率选择表面(FSS)结构的制作和加工提供参考和依据,对比研究了含片状银粉颗粒的聚氨酯基和环氧树脂基2种复合导电涂层的基本性能,并通过环境加速试验,重点研究了温度、湿度以及腐蚀气氛对2种导电涂层的界面强度、微观结构和导电性能的影响.通过电桥法测量涂层表面电阻的变化,并通过扫描电境观察环境试验前后,涂层表面和剖面的微观结构和形貌变化.试验结果表明:聚氨酯基涂层的综合性能优于环氧树脂基涂层;在实验所涉及的参数变化范围内,环境因素对2种涂层与基体的界面结合影响不大,但对其导电性能的影响比较明显.环境因素对导电性能的削弱作用,源于相应过程中导电涂层的微观结构损伤.     

Effect of Semi-solid Isothermal Heat Treatment on Microstructure of VW63Z Alloy

The effects of isothermal heat treatment on the semi-solid microstructure evolution of VW63Z (Mg-6Gd-3Y-0.4Zr, wt.%) alloy are studied. It shows that the microstructure of VW63Z alloy could transform from equiaxed crystal to semi-solid spherical crystal after isothermal heat treatment above 620 ºC. With the heating temperature elevating from 620 ºC to 635 ºC and the holding time prolonging from 10 min to 35 min, the liquid fraction increases gradually. The semi-solid microstructure evolution of VW63Z alloy can be divided into three stages, i.e., particle coarsening and spheroidization;particle necking, coalescence, and Ostwald ripening;and dynamic equilibrium. The semi-solid process window of VW63Z alloy ranges from 620 ºC to 635 ºC, where the best process parameters are holding at 635 ºC for 20 min?30 min. The solid fraction, the average particle size, and the shape factor are 41.1%?53.8%, 81.5 μm?83.2 μm, and 0.70?0.75, respectively. The maximum relative deviations of the solid fraction, the particle size, and the shape factor at different heights of the same billet are 44.6%, 17.4%, and 16.6%, respectively, which means that it should pay attention to the uniformity of edge and core of VW63Z alloy during isothermal heat treatment. The driving force of microstructure is supposed to be the reduction of solid-liquid interface free energy.     

Investigation of vertical profile of rain microstructure at Ahmedabad in Indian tropical region

The microstructure of rain has been studied with observations using a vertical looking Micro Rain Radar (MRR) at Ahmedabad (23.06°N, 72.62°E), a tropical location in the Indian region. The rain height, derived from the bright band signature of melting layer of radar reflectivity profile, is found to be variable between the heights 4600 m and 5200 m. The change in the nature of rain, classified on the basis of radar reflectivity, is also observed through the MRR. It has been found that there are three types of rain, namely, convective, mixed and stratiform rain, prevailing with different vertical rain microstructures, such as, Drop Size Distribution (DSD), mean drop size, rain rate, liquid water content and average fall speed of the drops at different heights. It is observed that the vertical DSD profile is more inhomogeneous for mixed and stratiform type rain than for convective type rain. It is also found that the large number of drops of size <0.5 mm is present in convective rain whereas in stratiform rain, drops concentration is appreciable up to 1 mm. A comparison of measurements taken by ground based Disdrometer and that from the 200 m level obtained from MRR shows good agreement for rain rate and DSD at smaller rain rate values. The results may be useful for understanding rain structures over this region.     

纳米TiC粉末改性钎料钎焊CBN磨粒的结合界面和磨损特性

采用了Ag-Cu-Ti 合金和纳米 TiC 粉末组成的新型复合钎料钎焊立方氮化硼(CBN)磨粒和工具基体,运用了三维体式显微镜和扫描电镜,研究了CBN磨粒与改性钎料之间的结合体系,包括界面微结构和反应产物,并进行了钎焊磨粒耐磨性试验.试验结果表明:加入的纳米TiC粉末均匀分布在钎料层内,细化了Ag-Cu-Ti合金钎料层的显微组织,有效控制了CBN磨粒与钎料的剧烈反应;磨粒表面化合物均匀致密,确保了CBN磨粒、纳米改性钎料和基体之间的结合强度;钎焊CBN磨粒的磨损形式以磨耗磨损为主,后期出现微小破碎,无磨粒脱落.     

Ti-6Al-4V钛合金激光弯曲成形微观组织研究

以1mm厚Ti-6Al-4V合金薄板为对象,运用光学金相显微镜、电子探针、扫描电子显微镜、氮氢氧联合分析仪、显微维氏硬度计,研究了特定累积线能量下90°弯曲角弯折区显微组织。结果表明,弯折区组织与累积线能量输入有关,当累积线能量在适当范围时,材料堆积增厚,极表层出现轻微复熔铸态组织,上层为板条马氏体α′,中层为针状马氏体α′,底层为长大粗化的(α+β)组织;距表层约0.2mm范围吸收间隙元素强烈致使硬度急剧提高并呈明显梯度;累积线能量输入过大,弯折区出现大面积复熔铸态组织并伴有裂纹产生。