超声速流中激波/湍流附面层干扰数值模拟

采用修正的B／L湍流模型以及多块结构化网格求解了二维N-S方程。分别对超声速流和高超声速流中的激波／湍流附面层干扰进行了数值研究。本文首先研究了进口马赫数为2．96的超声速流。计算结果准确预测了入射斜激波在平直壁面引起湍流附面层分离的流动特征：分离点的反射激波、分离包引起的膨胀扇以及再附点的反射激波。计算的壁面压力分布与实验值吻合较好，计算的分离区长度与实验值比较有一定误差。本文还对进口马赫数为9．22的高超声速流中压缩角引起的激波／湍流附面层干扰进行了数值研究。计算结果与实验结果吻合较好。     

The characteristics of sharp (small-scale) boundaries of solar wind plasma and magnetic field structures

We investigate properties of large (>20%) and sharp (<10 min) solar wind ion flux changes using INTERBALL-1 and WIND plasma and magnetic field measurements from 1996 to 1999. These ion flux changes are the boundaries of small-scale and middle-scale solar wind structures. We describe the behavior of the solar wind velocity, temperature and interplanetary magnetic field (IMF) during these sudden flux changes. Many of the largest ion flux changes occur during periods when the solar wind velocity is nearly constant, so these are mainly plasma density changes. The IMF magnitude and direction changes at these events can be either large or small. For about 55% of the ion flux changes, the sum of the thermal and magnetic pressure are in balance across the boundary. In many of the other cases, the thermal pressure change is significantly more than the magnetic pressure change. We also attempted to classify the types of discontinuities observed.     

环路热管内工质流动特性的研究

由于环路热管（LHP）具有高传热性能、远距离传输热量、优良的控温特性和管路的可任意弯曲、安装方便等特点，使LHP在航天热控领域有着广泛的应用前景。文章对LHP内工质的流动压力降进行了分析和计算；对毛细芯所能提供的最大蒸发传热能力进行了预测，并结合实验研究综合分析了毛细芯结构对LHP性能的影响。     

微结构谐振传感器

阐述了频率输出的新型谐振传感器的发展方向之一——微型化。评价性地论述了热激励硅谐振压力传感器和热激励谐振膜质量流量传感器。重点讨论了热激励的原理,特点等。指出我国应对传感器的这一发展趋势给予足够的重视。     

大厚度比零件（外侧）和波纹管（内侧）的缝焊研究

某重点型号波纹管组合件的设计要求是缝焊，对照以往产品的结构，比较明显的情况是波纹管在零件的内侧。零件的厚度是3mm，波纹管的厚度是0.1mm，零件与波纹管的厚度比比较大。波纹管在零件的内侧会产生一个问题：波纹管在焊接过程中会逐渐收缩，到最后与零件之间产生间隙，导致局部形不成焊缝。研究通过减小车配间隙,增加冷却手段、滚轮厚度和压力等措施来实现大厚度比的零件和波纹管之间的缝焊。     

飞机V型外倾双垂尾载荷校准技术

根据垂尾载荷校准及建模需求,对飞机V型外倾双垂尾结构受载情况进行了分析和简化,确定了校准试验载荷,研制了垂尾载荷校准试验专用龙门梁架。采用液压协调加载技术,完成了外倾双垂尾载荷校准试验,建立了满足测载要求的载荷模型。此种方法充分利用了左右垂尾外倾、双垂尾之间空间较大的特点,对左右垂尾对称施加向外的单点、多点载荷,加载载荷侧向分量左右自平衡,垂向分量依靠飞机自身重量即可平衡,飞机不需要复杂的固定与约束。试验中采用先搭建龙门框架,再停放飞机的方法,降低了试验风险、加快了试验进度,取得了良好的试验结果,对其他此类结构的载荷校准具有一定的借鉴作用。     

Families of halo orbits in the elliptic restricted three-body problem for a solar sail with reflectivity control devices

Solar sail halo orbits designed in the Sun-Earth circular restricted three-body problem (CR3BP) provide inefficient reference orbits for station-keeping since the disturbance due to the eccentricity of the Earth’s orbit has to be compensated for. This paper presents a strategy to compute families of halo orbits around the collinear artificial equilibrium points in the Sun-Earth elliptic restricted three-body problem (ER3BP) for a solar sail with reflectivity control devices (RCDs). In this non-autonomous model, periodic halo orbits only exist when their periods are equal to integer multiples of one year. Here multi-revolution halo orbits with periods equal to integer multiples of one year are constructed in the CR3BP and then used as seeds to numerically continue the halo orbits in the ER3BP. The linear stability of the orbits is analyzed which shows that the in-plane motion is unstable while the out-of-plane motion is neutrally stable and a bifurcation is identified. Finally, station-keeping is performed which shows that a reference orbit designed in the ER3BP is significantly more efficient than that designed in the CR3BP, while the addition of RCDs improve station-keeping performance and robustness to uncertainty in the sail lightness number.     

Hexapod多自由度微激励系统的振动时域波形控制

摘要： Hexapod多自由度微激励系统常用于航天器有效载荷在轨微振动环境的模拟，但采用现有控制方法无法精确稳定跟踪低频正弦加速度，这是由于系统耦合度高、非线性在低频段较强，被控对象相位滞后过大造成的.针对此问题，基于传统离线迭代控制方法，提出一种复合超前校正、多倍频陷波滤波器的改进离线迭代控制方法.其中，离线迭代进行补偿控制，超前校正进一步补偿系统相位，多倍频陷波滤波器去除非线性干扰.跟踪低频定频正弦加速度的实验结果表明，对比传统离线迭代控制方法，改进方法收敛快、控制精度高；对比现有自适应正弦振动控制方法，改进方法将符合精度要求的加速度控制频带下限由14.5 Hz扩宽至8 Hz.实验结果验证了所提方法的有效性.     

Effects of Mach numbers on Magnus induced surface pressure

Experimental and numerical methods were used to investigate the Magnus phenomena over a spinning projectile. The pressure force acting on the surface of a spinning projectile was measured for various cases by employing a relatively novel experimental technique. A set of miniature pressure sensors along with a data acquisition board, battery and storage memory were placed inside a spinning model and the surface pressure were obtained through a remotely controlled system. Circumferential pressures of the model for both rotational and static conditions were obtained at two different free stream Mach numbers of 0.4 and 0.8 and at different angles of attack. The results showed the ability of this new test method to measure the very small Magnus force via surface pressures over the projectile. The results provide a deep insight into the flow structure and illustrate changes in the cross-flow separation locations as a result of rotation. Similar results were obtained by the numerical simulations and were compared with the experimental data.     

一种基于Socket通信及PCIe的机载计算机设备测试管理技术研究

本文针对当前复杂机载计算机设备后期维护管理中存在的问题,提出了一种利用机箱内总线PCIe技术,将机箱设备视为整体进行一体化管理的设计方案,并结合Socket通信机制,设计出一种能够利用上位机软件完成机箱一体化管理的处理方法。