金属图象分割的研究

结合金属图象的特点,利用传统阚值分割技术和基于最大熵原则的图象分割技术对金属图象分割进行了分析;并根据金属图象分析要求,提出了先二值化金属图象再进行边缘提取的方法.对比实验结果表明,基于最大熵原则的图象分割技术可以获得较好的分割效果,所提出的方法能够获得连续闭合的晶粒边缘,为下一步的金属图象分析提供了可靠的依据.     

流变铸造法制备Al_2O_（3P）／ZA4－3复合材料的研究

为提高模用锌合金ＺＡ４－３的性能，扩大其应用范围，本项工作采用流变铸造法成功地制备了性能稳定的Ａｌ２Ｏ３Ｐ／ＺＡ４－３复合材料。对该材料进行了弯曲强度、冲击韧性、压缩强度、硬度及耐磨性等性能试验，结果表明：Ａｌ２Ｏ３ｐ的加入，使锌合金的压缩强度、室温和高温硬度以及耐磨性明显提高，其弯曲强度略有降低，而其冲击韧性下降了　。最后还讨论了成形工艺参数、颗粒含量和颗粒直径对该复合材料性能的影响。     

速度型切削颤振系统的数字仿真研究

本文采用数字仿真技术分析研究了速度型切削颤振系统的非稳定状态与颤振状态,内容包括起振阈与消振阈的分离、有限振幅不稳定性、系统参数对稳态颤振状态的影响。结果表明,起振阈与消振阈的分离现象是由切削宽度的连续变化引起的;有限振幅不稳定性与动态切削力中的三次项阻尼系数有关;动态切削力系数与机床结构系统参数对稳态颤振状态均有影响。     

CuAl2／Al复合材料的固相反应合成技术及与Al液的接触反应研究

研究了Ａｌ，Ｃｕ在真空状态下的纯固相接触反应情况，试验表明，Ａｌ粉、Ｃｕ粉在６００℃，保温６ｈ时，两者以完全发生反生成ＣｕＡｌ２（θ相），生成的θ相沿铝基体组织晶界分布并在结晶过程中具有择优取向特性，形成仅含沿晶界方向的主干与垂直于晶界的二次晶轴的树枝晶形貌。     

A novel surrogate modeling strategy of the mechanical properties of 3D braided composites

In this paper, a surrogate-based modeling methodology is developed and presented to predict the elastic properties of three dimensional (3D) four-directional braided composites. Using this approach, the prediction process becomes feasible with only a limited number of training points. The surrogate models constructed using Finite Element (FE) method and Diffuse Approximation, reduce the computational time and cost for preparing experimental samples. In the FE model, multiscale method is applied to couple the computations of elastic properties at microscale and mesoscale. Subsequently, a parametric study is performed to analyze the effects of the three design parameters on the elastic properties. Satisfactory results are obtained via the surrogate-based modeling predictions, which are compared with the experimental measurements. Moreover, the predictions obtained from surrogate models concur well with the FE predictions. This study orients a new direction for predicting the mechanical properties based on surrogate models which can effectively reduce the sample preparation cost and computational efforts.     

机载电子设备搭接技术研究

针对机载电子设备装机时的搭接环节,对机箱主要搭接技术进行了研究。根据设备搭接目的和性能要求,给出了相应的设备-托架、托架-安装支架之间的搭接方法,模块-机柜、机柜-安装支架之间的搭接方法,以及设备的备份搭接方法,并指出了各种搭接方式的特点、优点和不足,为设备的研制和机上安装提供搭接技术支持。     

Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

In situ formed TiB₂ particle reinforced aluminum matrix composites (TiB₂/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB₂ particles, the machinability is still a problem which restricts the application of TiB₂/Al MMCs. In order to meet the industrial requirements, the influence of TiB₂ particles on the machinability of TiB₂/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB₂/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB₂/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB₂/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.     

纤维增韧陶瓷基复合材料的比例极限应力与残余热应力关系

从细观力学角度分析并建立了纤维增韧陶瓷基复合材料从制备温度冷却到室温过程中产生的残余热应力与复合材料的比例极限应力的关系模型。该模型表明,减少复合材料的残余热应力或提高复合材料的纤维与基体的模量比,均可提高复合材料的比例极限应力。通过单调拉伸实验测试了先驱体浸渍裂解法(PIP)制备的2D SiC/SiC复合材料的比例极限应力,并采用文中建立的比例极限应力与残余热应力关系模型,计算出复合材料SiC基体的残余热应力为-19.5 MPa。分析表明,该结果是合理的。此外,引用了公开文献报道的5种复合材料体系数据,用于验证文中所建立的比例极限应力与残余热应力关系模型的适应性和可靠性,计算结果与实验结果最大误差为18.6%,表明该模型具有较好的适应性和可靠性,可为纤维增韧陶瓷基复合材料的研究提供新思路。     

气动钣金快速成形机的研制

针对电动钣金成形机制造成本高、效率低、易产生死点的问题,提出一种采用气液增力装置代替液压传动系统的气动钣金成形机设计方案。气液增力装置采用精密气压转换阀控制,实现行程平稳控制和加工成形过程平稳加载,显著提高了生产效率;配套研制的多种无齿收缩成形模具,可加工不同形状钣金件并获得更好的表面质量。该技术在钣金快速成形方面的研究处于国内领先水平,已获得3项国家专利。     

钣金成形信息化发展关键技术

钣金成形广泛应用在航空、汽车、船舶等各个行业,而钣金成形信息化在钣金成形技术中起重要作用.钣金成形信息的存储方式、关联技术、信息规范技术、数据库技术、钣金成形信息共享平台技术、钣金成形信息的获取和利用技术,是钣金成形信息化的关键技术.通过这些关键技术规范钣金成形信息的表达、存储方式,建立完善的钣金成形信息平台,利用数据挖掘技术,为钣金成形技术人员提供钣金成形工艺方案、工艺规程、模具设计需要的充足的信息.钣金成形信息化技术的发展将理顺钣金成形信息的积累和利用,消除信息孤岛,提高钣金成形的整体工艺水平和工艺准备效率.