复杂构件RTM整体成型工艺设计与仿真研究

以飞机预冷气引起口为典型构件,对其成型工艺进行探索,选择RTM成型工艺并应用PAM-RTM软件对RTM成型工艺影响参数进行虚拟仿真,确定模具设计的最终参数值.     

热处理工艺对2A70铝合金自由锻件力学性能的影响

研究了不同热处理工艺参数对2A70铝合金自由锻件力学性能的影响。首先采用正交试验分析了各因素对两个目标值(抗拉强度、延伸率)的影响;然后利用极差分析方法分析试验结果,指出各个因素对力学性能影响的主次顺序,并确定最优的热处理生产条件。试验结果表明:通过锻件锻后增加退火处理、适当提高固溶温度和选用合适的时效保温时间,该合金的力学性能得到了较大的改善,在保证抗拉强度大于等于375MPa要求的同时,延伸率由4%提高到了8.5%。     

Selective laser melting of Al–8.5Fe–1.3V–1.7Si alloy: Investigation on the resultant microstructure and hardness

This article presents the microstructure and hardness variation of an Al–8.5Fe–1.3V–1.7Si(wt%, FVS0812) alloy after selective laser melting(SLM) modification. Three zones were distinguished across the melting pool of the SLM-processed FVS0812 alloy: the laser melted zone(LMZ), the melting pool border, and the heat affected zone(HAZ) in the previously deposited area around the melting pool. Inside the LMZ, either an extremely fine cellular-dendritic structure or a mixture zone of the a-Al matrix and nanoscale Al_(12)(Fe,V)_3Si particles appeared. With a decreased laser beam scanning speed, the cellular-dendritic structure zone within the LMZ shrank significantly while the mixture zone expanded. The a-Al and Al_(12)(Fe,V)_3Si mixture zone was also observed in the HAZ, but another phase, submicron h-Al_(13)Fe_4 particles with rectangular or hexagonal shapes,formed along the melting pool border. Microhardness tests indicated that the hardness of the SLM-processed FVS0812 samples far exceeded that of the as-cast FVS0812 alloy.     

Single track and single layer formation in selective laser melting of niobium solid solution alloy

Selective laser melting (SLM) was employed to fabricate Nb-37Ti-13Cr-2Al-1Si (at%) alloy, using pre-alloyed powders prepared by plasma rotating electrode processing (PREP). A series of single tracks and single layers under different processing parameters was manufactured to evaluate the processing feasibility by SLM, including laser power, scanning speed, and hatch distance. Results showed that continuous single tracks could be fabricated using proper laser powers and scanning velocities. Both the width of a single track and its penetration depth into a substrate increased with an increase of the linear laser beam energy density (LED), i.e., an increase of the laser power and a decrease of the scanning speed. Nb, Ti, Si, Cr, and Al elements distributed heterogeneously over the melt pool in the form of swirl-like patterns. An excess of the hatch distance was not able to interconnect neighboring tracks. Under improper processing parameters, a balling phenomenon occurred, but could be eliminated with an increased LED. This work testified the SLM-processing feasibility of Nb-based alloy and promoted the application of SLM to the manufacture of niobium-based alloys.     

热等静压对激光选区熔化成形GH4169合金持久性能的影响

采用激光选区熔化(SLM)成形技术制备了GH4169合金,运用金相显微镜(OM)、扫描电子显微镜(SEM)、电子背散射衍射(EBSD)和透射电镜(TEM)等分析手段分析了热等静压对SLM成形GH4169合金组织及持久性能的影响规律。结果表明:沉积态合金组织中,沿沉积方向的晶粒为柱状晶,晶粒内枝晶组织细小,枝晶间分布大量Laves相;热等静压处理可有效消除组织中气孔缺陷,溶解大部分Laves相,促使组织晶粒等轴化,并减少后续980℃固溶处理过程中δ相在晶内的析出;热等静压处理能提高合金的持久寿命,但会降低合金的持久塑性。     

太空环境下电子束原位制造技术

美国国家航空航天局（NASA）载人探索计划的提出给载人登月和载人火星等带来了机会和风险,NASA的工程师和科学家正在开展在月球或火星表面利用当地提炼的材料进行原位制造工艺技术的研究。首先,介绍了太空原位制造和修复（ISFR）技术的概念和特点,结合该技术的发展背景,介绍了电子束原位制造技术的概念、特点以及在太空环境下应用的优势和潜力。然后,根据所用原材料和成形工艺原理的不同,电子束原位制造技术又分为电子束熔融（EBM）和电子束自由成形制造（EBF³）技术两个分支,分别介绍了这两个分支技术的概念、原理、特点以及采用该技术研制出的零件的性能,结合硬件设备的情况介绍了在太空环境下应用的适用性,同时也详细介绍了NASA利用兰利研究中心的C-9抛物线飞行试验系统进行电子束原位制造微重力试验的研究成果、试验数据和未来的发展趋势。最后,结合中国未来空间事业发展的需要,提出了关于发展太空环境下电子束原位制造技术的设想与建议。     

金属增材制造技术应用于军用飞机维修保障浅析

金属增材制造技术的发展为军用飞机维修保障提供了一条数字化、定制化、高性能、短周期的技术新途径,可提升军用飞机维修保障的技术水平和能力。本文综述了军用飞机维修保障的国内外现状,指出了金属增材制造技术的应用优势,介绍了军用飞机零件的典型损伤形式、不同增材制造工艺的适用性及修复工艺选取方案,分析了所涉及的逆向建模、结构优化、智能机器人等关键技术,详述了目前存在的技术成熟度与可靠性不高、修复原则不明确、标准规范不统一等主要问题及解决措施,指出了增材制造技术在军用飞机维修保障领域未来的发展方向和趋势,并给出了具体的应用建议。     

稀土镁合金铸件表面微观缺陷形成机理及修复技术

VW63Z稀土镁合金铸件表面微观缺陷经过荧光检测的结果表现为"条状荧光"现象,当该缺陷出现在铸件非加工面时,由于无法经过机械加工去除将直接导致铸件报废.本文探究了铸件表面缺陷的微观组织及其形成机理,结果表明微观缺陷主要成分为稀土氧化物的双层氧化膜,其中部分存在夹杂物;金属液汇流导致表面微观缺陷更易形成.应用激光熔凝技术...     

Experimental study of effect of post processing on fracture toughness and fatigue crack growth performance of selective laser melting Ti-6Al-4V

For Ti-6Al-4V, a titanium alloy increasingly used in aerospace structure, selective laser melting (SLM) is an attractive additive manufacturing technology, which is attributed to its complex construction capability with high accuracy and good surface quality. In order to obtain qualified mechanical properties, SLM parameters and post processing should be tailored for diverse service conditions. Fracture toughness and fatigue crack growth (FCG) behavior are critical characteristics for damage tolerance evaluation of such metallic structures, and they are affected by post processing technologies significantly. The objective of this study is to obtain the fracture toughness and fatigue crack growth behavior of Ti-6Al-4V manufactured by SLM, and to evaluate the influence of post-SLM thermomechanical treatment and surface machining. Fracture toughness and FCG tests were performed for SLM Ti-6Al-4V in three types of post processing status: as-built, heat treated and hot isostatically pressed (HIPed), respectively. Specimens with as-built and machined surface were tested. The microstructure and fractography were analyzed as well in order to investigate the relevance among manufacture process, microstructure and mechanical properties. The results demonstrate that as-built SLM Ti-6Al-4V presents poor ductility and FCG behavior due to martensitic microstructure and residual stresses. Both heat treatment and hot isostatic pressing improve the plane-stress fracture toughness and FCG performance considerably, while surface machining shows slight effect.     

航天高强不锈钢LMD成形缺陷分析及控制

为明晰航天高强不锈钢激光熔化沉积成形过程基础科学问题,推动其在航天液体火箭发动机领域的应用进程,针对航天高强不锈钢LMD成形过程中常见表面焊瘤、气孔、熔合不良等缺陷的形貌特征及产生机理进行深入分析,并提出对应的控制措施:通过优化边框扫描速度促进熔覆道的流动变形,极大减少了成形件侧表面及倾斜面的焊瘤缺陷; 使用PREP方...