复杂薄壁、薄板类零件高速加工技术初探

从加工方法,加工参数,工装夹具等方面对薄壁、薄板类零件的加工进行深入探讨,有效地解决了薄壁、薄板类零件的加工,为今后进行此类零件的加工进行了有益的技术储备。     

径向圆跳动误差的最小二乘评定数学模型和微机数据处理

用传统的测量方法只能得到被测零件的径向圆跳动误差的近似值。为了得到该项误差的准确值，需要研究新的测量方法。建立了径向圆跳动误差最小二乘评定数学模型，并编制了高级语言数据处理程序。在万能工具显微镜上获得了采样数据，给出了计算结果。     

ABORT-like detector to combat active deceptive jamming in a network of LFM radars

This paper studies an electronic counter-counter measures (ECCM) scheme combating against deceptive electronic counter measure (ECM) techniques.An adaptive detector exploiting generalized likelihood ratio test (GRLT) criterion is applied to detect the presence of deceptive jamming in fractional Fourier transform (FrFT) domain.First,the generating mechanism of spurious frequencies is analyzed based on the Volterra serial.The proposed nonlinear distortion model based on power amplifier behavior is robust in distortion analysis when the memory effect is considered.Second,a modified adaptive beamformer orthogonal rejection test (ABORT) like detector in closed form is built.The proposed detector can discriminate the echo and deceptive jamming adaptively by exploiting primary data and secondary data.This ECCM scheme is capable of guaranteeing the performance without the restriction of orthogonality,which is essential for the ABORT detectors.The expansion to radar network is discussed as a special case at the final part of this paper.Numerical simulations demonstrate the effectiveness of the proposed method.     

Latitudinal distribution of solar coronal active regions

We studied the cyclic evolution of the latitudinal distribution of solar coronal active regions based on daily images from SOHO EIT for the period 1995–2017. Fully automated software was used, which included the following steps: initial preparation of images in the data series, normalization of histograms and correction of limb brightening, segmentation of images using threshold intensity values obtained from their histograms, scanning of segmented images in heliographic coordinates and obtaining profiles of latitudinal distribution of coronal active regions for each image of the data series. From the output data, we obtained a temporary change in the latitudinal distribution profiles and the migration of activity centers on the solar disk. From the period of minimum activity to the next minimum in both hemispheres, activity centers begin to migrate from high latitudes towards the equator. At the same time, the general center of activity repeatedly changes the direction of migration. The latitudinal distribution of the so-called presence factor of coronal active regions closely resembles the magnetic butterfly diagram, which proves their direct causal relationships. Variations in the presence factor of coronal active regions are correlated with cyclic variations in the sunspot daily numbers.     

薄膜电阻温度计原理性误差分析及数据处理方法研究

薄膜电阻温度计是高超声速测热试验中一种常用的传感器,多用于激波风洞中.改进薄膜电阻温度计测热数据的后处理方法,分析其原理性误差,提出修正方法,可以进一步提高热流测量精度,为防热设计提供可靠数据.应用三维热传导理论,考虑热流和温升的耦合影响,计算了气动加热条件下薄膜电阻温度计结构温升情况,得到了铂层内的温度分布规律,并与一维半无限简化理论得到的薄膜电阻温度计表层温度相互对比,得到了模型简化带来的原理性误差;建立了由表面温升计算表面热流的导热反问题计算方法,与经典的Cook-Felderman处理公式和热电模拟网络处理方法相互对比,提出了修止热流值的方法,为提高热流测量精度提供了一种可行的手段.     

新电位移边界条件下的压电介质断裂问题

应用边界元法,并结合一种特殊的复变函数基本解,研究了压电介质的断裂问题。由于该基本解完全遵循本构方程没有对电位移边界作假设,所以结论同非穿透性裂纹假设的结果有较大差异。通过计算表明,外加力载荷不但会引起裂纹尖端应力奇异性,也会引起电场奇异性,同样,外加电压也会引起裂纹尖端应力奇异性。     

航测法提取动态三维深度信息

目前提取三维信息,重建三维图像的研究很多,本文叙述的是仅用一台摄像机利用航测法来提取动态三维信息的方法。假设物体不动,移动摄像机。在移动摄像机前后,即在摄像机移动的相邻两点,可以得到模型的像片对,通过此像片对来实现同名点交会,求得未知点的三维深度信息。为此,首先要进行绝对定向,计算像片元素和确定各个坐标系。然后实现不依赖像片角定向元素的同名点空间交会;或实现利用对应轴系上的坐标进行空间交会。在此基础上,笔者充分利用先验条件和专家知识来确定飞机模型上的同名点,初步得到了飞机模型的轮廓侧视图。     

神经网络在未来超分辨雷达中的应用

最新的技术发展已为研制超分辨雷达创造了条件。它能够突破普通雷达基于匹配滤波原理的分辨能力,而实现超分辨。超分辨雷达的巨大计算量通常来自求解非线性最小二乘问题时的多维搜索。本文针对这一问题,研究了雷达信号处理中的两个典型例子:(1)利用阵列处理检测个数已知而方向未知的雷达目标;(2)对波音727飞机进行超分辨距离多普勒成像。说明Hop-field神经网络通过集体运算能够求解各种困难的最优化问题,因而在未来的超分辨雷达中有广阔的应用前景。     

一种简单有效的层合板壳单元

本文通过修正普通四边形单元的横向剪切应变能而得到了一种新的四边形四节点壳单元(本文称之为L_3单元)。该单元每个节点有五个自由度,适用于各向同性、正交异性和层合板壳的线性、非线性及稳定性有限元分析。文中给出了各种类型板壳结构的算例。数值结果表明,该单元不仅公式简单、自由度少,而且具有令人满意的精度和收敛特性。     

Ni-7.3%Si-2.2%B合金快淬组织与深过冷快凝机制

 采用B_2O_3玻璃和纯循环过热净化相结合的方法去除液态金属中的异质晶核,使液态Ni-7.3％Si-2.2％B合金获得了330K的过冷度。对比分析了该合金在低温基板上的快淬薄片与大体积深过冷试样的微观组织。借助计算机和红外测温系统,快速采集了熔体的再辉过程。数据处理发现,在深过冷液态金属的整个再辉区间,温度的上升速率呈瞬态变化特征,再辉时间随初始过冷度的提高而减小。最后,由再辉曲线确定出深过冷液态金属再辉过程中的固相分数与时间以及凝固速度与瞬时过冷度的关系。