Effect of U-grooves on high-lift low pressure turbine profile＇s incidence characteristics

以某高负荷低压涡轮叶型为研究对象,分析了该叶型在低雷诺数下的攻角特性,并应用了表面嵌壁式U形槽的被动控制方法来提高该叶型的攻角裕度.数值模拟的结果表明：相比较大的正攻角流动状况,叶型较大的负攻角并不会引起吸力面大的流动分离,从而减小了叶型损失;表面嵌壁式U型槽通过推迟分离、加速再附来减小分离泡甚至减小湍流湿面积,从而降低叶型损失;表面嵌壁式U型槽能否提高该叶型的攻角裕度与开槽位置和深度有关系,在±15°攻角范围内72%轴向弦长位置处开槽明显的降低了叶型损失而开槽深度为0.40mm时叶型损失最小.     

细节疲劳额定强度计算参量取值敏感性研究

 现代民机设计中细节疲劳额定强度(DFR)方法占据重要地位。为了研究DFR方法中的参数敏感性问题,针对典型航空材料讨论了在斜度参数和分散性参数两种参数的变化范围内,直接采用波音设计许用值进行DFR计算可能造成的误差水平,并与简单的扰动分析结果进行了对比;推导了基于Gerber方程计算DFR值的新公式,并对其适用性进行了对比分析。结果表明,在上述计算参量中斜度参数对国产材料DFR计算结果影响最敏感;锻铝等延性材料更适于使用基于Gerber方程的DFR公式。     

基于复合疲劳试验的涡轮叶片振动应力反推法

提出了一种利用复合疲劳试验和外场故障数据反推涡轮叶片实际振动应力的方法.该方法针对与故障叶片同批次的叶片,开展数个振动应力水平下的单件试验和某一特定振动应力水平下的成组试验,利用极大似然法推导出叶片的概率-应力-寿命曲线(P-S-N);最后基于99.87%存活率下的概率-应力-寿命曲(P_99.87%-S-N),结合叶片的外场故障统计结果,反推出叶片实际工作中振动应力的范围和可能的最大振动应力.      

激光冲击强化提高主动连杆振动疲劳性能

针对某型发动机放气活门主动连杆转接R处的疲劳断裂问题,进行了主动连杆激光冲击强化工艺研究;完成了原型件和激光冲击强化、喷丸及加大R3种处理工艺后主动连杆振动疲劳对比试验.结果表明,在317MPa的应力水平下,激光冲击强化、喷丸和加大R后主动连杆疲劳寿命分别为原型件的5.24倍、3.89倍及1.36倍;与其它2种工艺相比,激光冲击强化具有强化效果好、工艺稳定性高、易于实现等优点,是截至目前减少主动连杆疲劳断裂故障的最佳处理工艺.主动连杆激光冲击强化后表面粗糙度较小,产生深度约1.4mm的高数值残余压应力层,表层晶粒细化至纳米晶并伴随高密度位错.三者共同作用可以有效缓解转接R处的应力集中,抑制疲劳裂纹在转接R处的萌生和扩展,是主动连杆振动疲劳寿命提高的主要原因.     

聚酰亚胺/无机氧化物复合薄膜的制备与耐原子氧性能

分别以锆酸四丁酯、钛酸四丁酯和正硅酸乙酯为氧化物前驱体,利用溶胶凝胶法制备了一系列聚酰亚胺/无机氧化物复合薄膜,在原子氧地面模拟设备中进行了原子氧暴露实验,原子氧累计通量约为3.1×10²⁰ atom/cm².分别考察了无机氧化物种类和含量对复合薄膜力学性能和耐原子氧性能的影响.结果表明,无机氧化物在聚酰亚胺基体中的分散形态对其力学性能影响很大;原子氧暴露后,聚酰亚胺薄膜表面分别形成了富锆、富钛和富硅的保护层,质量损失率减小,耐原子氧性能明显提高.     

泵前阀开关波纹管组件改进设计

某型号发动机泵前阀在抽典试验中开关腔波纹管组件发生了疲劳失效,经对失效原因及机理进行分析,对波纹管组件进行了改进设计,并对原状态波纹管组件及新设计进行了有限元计算分析和疲劳寿命估计。计算结果表明,新设计波纹管应力分布相对合理,疲劳寿命水平有较大提高。设计改进后生产了试验件并进行了阀门试验,试验与计算结果相当并满足发动机使用要求。     

依托ERP实现固定资产全寿命周期管理

固定资产是企业的重要劳动资料,是实现资产保值增值的重要工具。现有的固定资产管理模式已经无法应对当前电网企业对固定资产管理新形势的要求。资产全寿命周期管理是以资产的整体目标出发,统筹考虑资产的整个生命周期,在满足安全、效能的前提下追求资产全寿命周期成本最优的管理模式。本文提出通过运用ERP系统在固定资产生命周期内构建出一套完整的固定资产管理新模式,并通过在某地市级供电公司的实际运用,得出了运用此种新模式可以实现固定资产使用效率提高、全寿命周期成本降低的管理新要求。     

Designing method of acceleration and deceleration control schedule for variable cycle engine

Studies show that different geometries of a Variable Cycle Engine (VCE) can be adjusted during the transient stage of the engine operation to improve the engine performance. However, this improvement increases the complexity of the acceleration and deceleration control schedule. In order to resolve this problem, the Transient-state Reverse Method (TRM) is established in the present study based on the Steady-state Reverse Method (SRM) and the Virtual Power Extraction Method (VPEM). The state factors in the component-based engine performance models are replaced by variable geometry parameters to establish the TRM for a double bypass VCE. Obtained results are compared with the conventional component-based model from different aspects, including the accuracy and the convergence rate. The TRM is then employed to optimize the control schedule of a VCE. Obtained results show that the accuracy and the convergence rate of the proposed method are consistent with that of the conventional model. On the other hand, it is found that the new-model-optimized control schedules reduce the acceleration and deceleration time by 45% and 54%, respectively. Meanwhile, the surge margin of compressors, fuel–air ratio and the turbine inlet temperature maintained are within the acceptable criteria. It is concluded that the proposed TRM is a powerful method to design the acceleration and deceleration control schedule of the VCE.     

Integration of high-fidelity model of forward variable area bypass injector into zero-dimensional variable cycle engine model

Forward Variable Area Bypass Injector (FVABI) is one of key components which contributes to modulate the cycle parameters of Variable Cycle Engine (VCE) under various operation conditions. The modeling method of zero-dimensional FVABI was reviewed and its deficiency was analyzed based on FVABI flow characteristic. In order to improve the accuracy of VCE performance simulation, the high-fidelity modeling method of FVABI was developed based on its working characteristics. Then it was coupled with the zero-dimensional VCE model and the multi-level VCE model was built. The results indicate that the geometric and aerodynamic parameters can affect the interaction between the two airflows and the zero-dimensional FVABI model is too simple to predict the component performance accurately, especially when the FVABI inner bypass is chocked. Based on the performance curves for single bypass mode and the regression model of multi-scale support vector regression for double bypass mode, the high-fidelity model can predict FVABI performance accurately and rapidly. The integration of high-fidelity FVABI model into zero-dimensional VCE model can be done by adjusting iterative variables and balance equations. The multi-level model has good convergence and it can predict VCE performance when the FVABI inner bypass is chocked.     

火箭引射模态下主火箭总压与RBCC发动机的匹配性

基于传统的"等压面假设"理论,建立了RBCC发动机主火箭的引射性能分析模型,研究了主火箭总压与RBCC发动机的匹配性。研究结果表明,若隔离段通道面积比小于0.65,在主火箭总压较低条件下,隔离段内二次流容易达到壅塞,无法进一步提高空气流量;在地面静止状态下,随主火箭总压增加,空气流量逐步增大,等压面上形成Fabri壅塞后,进一步增加主火箭总压,反而会降低空气流量;在火箭引射模态下,RBCC发动机的工作状态可细分为引射作用占主导地位的进气道亚临界状态和临界状态、冲压作用占主导地位的进气道超临界状态,其分界马赫数分别约为0.7和1.5。