Autonomous Control Reconfiguration of Aerospace Vehicle Based on Control Effectiveness Estimation

未来空天飞行器跨空天两域飞行,要求有较高的自主性以适应由故障和环境变化带来的不确定因素。针对空天飞行器的不确定性,提出了自主控制重构方案。研究了线性模型的时变控制效益的估计方法,提出并证明了效益矩阵可估计的充分条件,给出了相应的算法并证明了其收敛性和对噪声的鲁棒性;提出了基于线性规划和模糊逻辑的控制分配算法,通过冗余效应器实现了不确定条件下的自主控制重构。系统集成和仿真结果分析验证了方案和算法的有效性。     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

自动测试系统适配器自动设计技术

 针对当前自动测试系统（ATS）适配器设计中存在的“自动化程度较低、缺乏通用性”的不足,开发了ATS通用适配器自动设计技术。建立了一整套通用适配器自动设计流程,在依次完成通用端口设计、UUT测点资源匹配、适配器开关网络设计、相关工程设计后即可实现自动设计一个通用适配器的目的。以某机载通讯设备自动测试系统为例,采用该技术可缩短ATS适配器开发周期至原来的1/3,降低开发成本,提高设计的标准化、通用化程度,适配器需要量由5个减为1个。     

New Cutting Force Modeling Approach for Flat End Mill

A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions.     

Energy-optimal trajectory planning for solar-powered aircraft using soft actor-critic

High-Altitude Long-Endurance(HALE) solar-powered Unmanned Aircraft Vehicles(UAVs) can utilize solar energy as power source and maintain extremely long cruise endurance,which has attracted extensive attentions from researchers. Trajectory optimization is a promising way to achieve superior flight time because of the finite solar energy absorbed in a day. In this work,a method of trajectory optimization and guidance for HALE solar-powered aircraft based on a Reinforcement Learning(RL) framework is...     

Space time clock: An on-chip clock with 10-12 instability

High precision and stable clock is extremely important in communication and navigation. The miniaturization of the clocks is considered to be the trend to satisfy the demand for5G and the next generation communications. Based on the concept of meter bar and the principle of the constancy of light velocity, we designed a micro clock, Space Time Clock(STC), with the size smaller than 1 mm × 1 mm and the power dissipation less than 2 m W. Designed in integrated circuit of 0.18 μm technology, the in...     

Neural Network aided PMSM multi-objective design and optimization for more-electric aircraft applications

This study uses the Neural Network(NN) technique to optimize design of surfacemounted Permanent Magnet Synchronous Motors(PMSMs) for More-Electric Aircraft(MEA)applications. The key role of NN is to provide dedicated correction factors for the analytical PMSM mass and loss estimation within the entire design space. Based on that, a globally optimal design can be quickly obtained. Matching the analytical estimation with Finite-Element Analysis(FEA) is the main research target of training the NN. ...     

压力对膜盒式端面密封平衡直径的影响

膜盒式端面密封在低温液体火箭发动机涡轮泵中有着广泛的应用,作为直接影响密封工作稳定性及涡轮泵工作可靠性的重要参数,端面比压、膜盒平衡直径等如何选取一直是密封设计的重要工作.以某型低温液体火箭发动机涡轮泵的膜盒式端面密封为研究对象,研究压缩量、工作压力对膜盒应力分布、平衡直径、载荷系数和端面比压的影响.应用有限元法建立了...     

典型轨道环境效应及对在轨卫星影响分析

近年来,各航天大国对空间轨道资源的挖掘与应用不断拓展.超低轨道、椭圆轨道、坟墓轨道、拉格朗日点等,因其在快速重访、定点观测、空间攻防、科学探索等方面的优势,逐步纳入各国防灾减灾、战事快响、导弹预警、空间突防和太阳观测等应用领域.随着卫星在轨经历的空间环境变得更加复杂,空间环境效应引发的卫星故障和异常情况日益突出.本文围...     

无人平台复杂地形探测的视触融合方法

为提高无人平台在复杂环境中的地形探测能力以及解决在小样本数据下识别地形困难的问题,提出了一种无人平台复杂地形探测的视触融合方法。在原始宽度学习的基础上,建立了多模态级联特征节点宽度学习框架。首先进行触觉和视觉初步特征提取和融合特征提取,随后将融合特征矩阵经宽度学习分类器得到地形识别的结果。最后,在自建的视觉-触觉地形 (V-T2)数据集进行了实验验证。结果表明,相比于传统的融合算法,提出的融合算法有很好的准确性和鲁棒性,为无人平台地形探测提供了有效的策略。