FC-AE-1553网络传输性能评价

为了提高航天航空网络传输性能,提出一种通用的FC-AE-1553网络传输效率计算方法并研制高性能FC-AE-1553节点卡.首先,对FC-AE-1553网络的消息传输过程进行详细分析,分析信息类型,给出传输帧的格式建议,通过分析FC-AE-1553协议中各类消息传输的时间参数,结合FC标准中对通信时间的要求,提出FC-AE-1553网络交换中各种消息类型的通信时间计算公式.然后, 针对无差错传输和有差错传输两种情况,给出了网络传输效率的计算方法.最后,通过仿真分析数据帧净荷长度、节点处理时间、交换中序列数量、传输误码率、丢包率等参数对FC-AE-1553网络传输效率的影响,给出了网络优化设计的建议.依托某航天工程任务,研制了基于XC5VFX100T和MPC8536E的FC-AE-1553节点卡.实验结果表明:丢包对传输效率的影响可忽略;数据帧净荷为2 048 B,数据帧数量为16时,传输效率可达到77.2%.      

Discrete time multiple spacecraft formation flying attitude optimal control in presence of relative state constraints

This paper addresses the challenge of synchronized multiple spacecraft attitude reorientation in presence of pointing and boundary constraints with limited inter-spacecraft communication link. Relative attitude pointing constraint among the fleet of spacecraft has also been modeled and considered during the attitude maneuvers toward the desired states. Formation fling control structure that consists of decentralized path planners based on virtual structure approach joint with discrete time optimal local controller is designed to achieve the mission’s goals. Due to digital computing of spacecraft’s onboard computer, local optimal controller based on discrete time prediction and correction algorithm has been utilized. The time step of local optimal algorithm execution is designed so that the spacecraft track their desired attitudes with appropriate error bound. The convergence of the proposed architecture and stability of local controller’s tracking error within appropriate upper bound are proved. Finally, a numerical simulation of a stereo imaging scenario is presented to verify the performance of the proposed architecture and the effectiveness of the algorithm.     

伺服机构负载模拟系统设计与动态特性分析

针对火箭发动机喷管伺服机构的负载模拟问题,采用机械的方式,设计了一种可对伺服机构的惯性负载、摩擦力矩负载、弹性力矩负载、安装刚度以及发动机喷管柔性特征进行模拟的负载模拟器,并建立了模拟器和伺服机构数学模型。仿真分析了惯性负载、弹性力矩以及喷管柔性对伺服机构负载多自由度特性的影响。通过对伺服机构扫频实验,负载模拟器中的负载在一定范围内调节,可复现伺服机构实际工作中的动态特性。说明该负载模拟器结构设计合理,从而为具有多自由度特性的火箭伺服机构的负载模拟系统设计提供参考。该系统已经得到实际应用。     

星地动态双向时间同步与测距算法

针对卫星运动对星地距离和钟差测量的不利影响,提出一种基于最小二乘拟合的星地动态双向时间同步与测距算法。在建立星地可视模型基础上,仿真了MEO运动卫星与地面时间同步站之间星地距离的变化规律,分析了卫星运动对星地双向时间同步与测距的主要不利影响。该算法首先利用星地双向时间同步数据分别生成星地距离和钟差拟合多项式,然后联合求解出运动卫星误差最小的星地距离与钟差。实验结果表明了该算法的合理性和科学性,在包含仿真误差的条件下,其时间同步精度优于3ns,测距精度优于3m。将其应用到各种空天应用系统的星地时间同步与测距中,可以消除卫星运动对双向时间同步与测距的不利影响,提高时间同步与测距精度。     

载人航天器的可重构式控温回路系统设计

文章提出了载人航天器的可重构式控温回路系统,它由独立的中低温内外回路系统组成,可改善低温内回路由于控温点温度较低而对辐射器散热能力带来的影响,还可在某个外回路辐射器故障时进行系统重构,维持回路功能。建立了控温回路系统非稳态仿真分析模型,对正常工作模式下和某外回路故障工作模式下各舱回路控温点温度、设备温度、流量分配和载人航天器热负荷水平进行了分析。结果表明,双外回路系统比单外回路系统散热能力高27%。当双外回路中某回路故障时,通过系统重构,外回路系统可维持1850W散热能力,能保障载人航天器平台安全,表明可重构式控温回路系统能提高系统可靠性。     

Experimental study of a flush wall scramjet combustor equipped with strut/wall fuel injection

In this study a flush wall scramjet combustor is tested in a supersonic incoming air flow with the Mach number of 3 which is generated by an air vitiation heater producing the stagnation temperature of 1505 K. Using liquid kerosene as the fuel, the flame is stabilized by means of a centrally mounted O₂ pilot strut after being ignited by a plasma torch. During experimental measurements, the fuel is injected with a constant equivalence ratio of 0.8 according to specified strut/wall injection ratios, i.e., a portion of the fuel amount is injected from the strut while the rest is injected from the wall. The strut and wall injectors are arranged at the same axial position. The combustion performance and wall temperature gradients are evaluated with various fuel feeding ratios between the wall and the strut. Experimental results show, when the equivalence ratio is constant and the axial injection position is fixed, the combustion characteristics vary significantly with the strut/wall fuel feeding ratio, especially when this ratio is close to its lowest and highest limits. Among the four fuel feeding ratios examined, the strut only injection mode and the average distributed strut/wall injection mode show the best combustion performance. However, the strut/wall injection mode produces a smaller wall temperature gradient compared to the strut only injection mode, which is due to the significant film cooling effect caused by the wall injected liquid kerosene.     

铝合金薄板零件橡皮囊成形屈曲分析与实验

为了抑制铝合金薄板类零件在橡皮囊成形后出现屈曲的缺陷,采用薄板屈曲微分方程对零件成形后的屈曲进行理论分析,并通过橡皮囊成形实验研究自然时效时间和成形压力对屈曲缺陷的影响。理论分析结果表明：零件法兰屈曲波数与其内外径比有关,通过改变法兰宽度进行实验验证,实验结果与理论分析结果相符;而成形实验结果表明,屈曲缺陷高度随板料自然时效时间的增加而增加,随成形压力的增加而减少。因此,理论分析结果有效,并且可通过减少淬火后成形时间和增加成形压力来抑制屈曲缺陷。     

空间高阶差分近似对三维ADI-FDTD数值色散的影响

研究采用空间高阶差分近似的三维交替方向隐式时域有限差分法(ADI-FDTD,Alternating-Direction Implicit Finite-Difference Time-Domain)数值色散问题,首先推导了采用空间高阶差分近似的数值色散迭代公式,分别对最小相速方向和最大相速方向进行二阶、四阶、六阶、十阶空间差分数值色散误差的数值计算和比较,并分析数值色散对空间差分阶数的依赖关系,最后发现在均匀网格中采用四阶空间差分能得到较好的效果.     

一种新型的基于预测的卫星资源分配方法

针对传统的按需分配方式所造成的长时延问题,提出了一种新型的基于业务预测的按需分配方法。该方法通过预测业务在等待队列中的长度,将预测信息发送给网络资源控制中心,再由控制中心动态地分配带宽资源,达到服务质量的要求。在阐述了按需分配和业务预测的基本算法后,通过仿真分析了不同的业务类型采用不同的预测信息发送间隔时间的时延性能,分析中考虑了实时业务比非实时业务享有更高的优先权,并且比较了常规按需分配与基于业务预测的按需系统分配方法的时延性能。仿真结果表明利用业务预测,选择合适的预测信息发送间隔时间,能够有效地改善带宽资源分配的时延性能,相比一般的按需分配方式服务质量有了明显的提高。