卫星推进及控制装置准直测量方法研究

在传统的卫星推进及控制装置准直测量方法的基础上,提出两种新的测量方法,即小角度准直测量法和三维坐标准直测量法,并给出了相应的数据处理方法。所提出的方法测量精度高、测量速度快,无需转台整平,也不必对转台上的定位销进行精确准直。     

质量矩导弹的神经网络及自适应非线性控制

本文对质量矩控制导弹的动力学方程简化和控制系统的设计进行了研究。详细阐述了所提出的控制方法，介绍了径向基单隐层神经网络进行误差补偿的算法原理，用Lyapunov理论证明了所采用方法的稳定性。在给出了质量矩导弹的六自由度动力学方程和简化后的方程后，用所提出的方法设计控制系统。通过仿真分析，得出了本文所提出的方法具有较好的误差补偿能力的结论。     

气动力星座保持的闭环控制研究

本文研究了利用气动力进行星座保持的闭环控制问题。提出了一种改进的半全局指数收敛闭环控制律，对于指定的任意大的有界域，利用不变集定理论上证明了该控制律的稳定性和抗干扰性，又提出了双ε法以提高响应速度。     

三轴稳定遥感卫星姿控系统故障情况下的系统重构

论述三轴对地稳定遥感卫星姿控系统中部分轮子或部分陀螺故障情况下的姿控系统重构。文中论述了只在俯仰通道有一偏置动量轮正常工作，而滚动和偏航通道轮子故障条件下的系统重构。另外还论述了偏航陀螺故障，姿控系统其它部件正常情况下，控制系统采用Whecon原理与PIM控制相结合的设计。以上两种系统重构拟用于实际系统中，经过数学仿真验证，姿控系统在故障情况下能够完成基本任务。     

多点法测量形状误差的补偿控制系统

经过对误差分离技术理论进行了分析之后,又对误差补偿技术进行了研究,并建立了多点法测量形状误差的补偿控制系统。通过补偿主轴径向误差运动,提高了工件的圆度误差和圆柱度误差。     

Tunnel/predictor display with two-axis control coordination and simplification

A longitudinal-lateral control coordination and simplification concept is considered for a tunnel/predictor display, which presents the command flight path and a specified future aircraft position in a 3-dimensional format to the pilot, for improving flight path control. A basic element of the proposed concept is the generation of common longitudinal-lateral transfer characteristics of the predictor-aircraft system for the crossover frequency region. Control coordination is supported by a dynamics similarity between the longitudinal and the lateral response characteristics of the predictor position in closed-loop pilot control actions. The control coordination and simplification concept is considered to support the pilot in manual flight path control, directed at an enhancement of his control performance and at a reduction of his workload. Results from pilot-in-the-loop simulation experiments support the theoretical findings and show the effectiveness of the proposed predictor concept with control coordination.     

满足约束的Gn连续过渡曲面的构造

在Erich Hartmann提出的由两基曲面线性组合构造G^n连续过渡曲面方法的基础上，针对该方法存在很难找到合适的参数变换的问题，提出了一种基于基曲面局部区域重新参数化构造G^n连续过渡曲面的方法。通过对基曲面上切触线附近区域部分曲面重新参数化，再由重新参数化局部基曲面线性组合构造G^n连续过渡曲面。这样将两基曲面间构造过渡曲面的问题转化为在重新参数化局部基曲面间构造过渡曲面。以构造G^1连续的翼身融合面为例，讨论了满足约束要求条件时G^2连续过渡面的构造方法。即先对基曲面上过渡切触线附近的局部区域进行重新参数化，后通过优化求解来确定比例因子和偏移量、平衡因子和调配因子，使过渡曲面满足前后边条线约束，最后利用线性组合来构造G^2连续的过渡面。约束过渡曲面的形状可通过改变重新参数化基曲面的大小来调整．     

飞机主操纵系统疲劳试验载荷谱小操纵位移频次问题研究

针对飞机全机主操纵系统疲劳试验载荷谱中小操纵位移频次影响问题进行了分析和讨论,确定了某机全机主操纵系统小操纵位移频次的级别。同时,在原某机全机主操纵系统疲劳试验载荷谱的基础上再次对其小操纵位移频次进行了计算,去掉了这一级别以下对全机主操纵系统疲劳试验无影响的小操纵位移频次,从而完善了主操纵系统疲劳试验载荷谱。另外,对小操纵位移频次问题研究结果在其全机主操纵系统疲劳试验中的实施效果进行了阐述。     

What Determines the Composition of SEPs in Gradual Events?

Gradual solar energetic particle (SEP) events are evidently accelerated by coronal/interplanetary shocks driven by coronal mass ejections. This talk addresses the different factors which determine the composition of the accelerated ions. The first factor is the set of available seed populations including the solar wind core and suprathermal tail, remnant impulsive events from preceding solar flares, and remnant gradual events. The second factor is the fractionation of the seed ions by the injection process, that is, what fraction of the ions are extracted by the shock to participate in diffusive shock acceleration. Injection is a controversial topic since it depends on the detailed electromagnetic structure of the shock transition and the transport of ions in these structured fields, both of which are not well understood or determined theoretically. The third factor is fractionation during the acceleration process, due to the dependence of ion transport in the turbulent electromagnetic fields adjacent to the shock on the mass/charge ratio. Of crucial importance in the last two factors is the magnetic obliquity of the shock. The form of the proton-excited hydromagnetic wave spectrum is also important. Finally, more subtle effects on ion composition arise from the superposition of ion contributions over the time history of the shock along the observer’s magnetic flux tube, and the sequence of flux tubes sampled by the observer.     

滚珠丝杠螺距误差补偿法提高数控机床定位精度的研究

在详细论述、对比了实现数控机床滚珠丝杠螺距误差补偿的硬件、软件方法的原理基础上,对滚珠丝杠螺距误差软件补偿法可有效提高数控机床的定位精度进行了试验验证。