一类二阶三点边值问题解的存在性

运用上下解方法,研究了一类二阶混合非线性边值条件的三点边值问题,通过构造了适当的非线性辅助函数工得到了解存在的充分条件,推广和改进了某些已知的结果。     

涡扇发动机早期退化性能的线性变参数估计

针对涡扇发动机线性变参数(Linear parameter varying,LPV)模型,给出了一种新的早期退化航空发动机部件性能LPV滤波器设计方法.该方法采用仿射依赖于参数的二次Lyapunov函数,在仿射二次稳定性的基础上,引入多凸性引理将滤波器求解问题转化为线性矩阵不等式(Linear matrix inequalities,LMI)约束下的凸优化问题,避免了求解参数化线性矩阵不等式(Parameterized linear matrix inequalities,PLMI)约束下的优化问题.针对某型早期退化涡扇发动机的仿真表明,该方法能以较高精度估计性能退化参数,且鲁棒性强,增益调度简单,具有一定的工程意义.      

基于经验模态分解的燃烧不稳定性分析

实验研究了在常温常压条件下贫燃预混旋流火焰的燃烧不稳定性,发生燃烧不稳定性时其压力脉动表现为非平稳信号.利用一种基于经验模态分解(EMD)的希尔伯特-黄变换(HHT)算法对在当量比分别为0.71和0.80工况下的压力脉动信号进行了时频分析.针对压力脉动信号进行经验模态分解,选取主要的固有模态函数(IMF),对IMF通过HHT变换得到瞬时频率并进行统计分析.结果表明:在当量比为0.71时,压力信号呈间歇式的脉动,其振型为拍振;在当量比为0.80时,脉动压力信号则呈现出极限环振型.在基于EMD的HHT变换中,IMF体现了燃烧不稳定性的固有模态且具有自适应性强的特点.      

基于模型的民机自动飞行功能分析与设计

描述了民用飞机自动飞行系统基于模型的功能分析与架构设计过程。该研究采用符合现代系统工程理念的模型化设计形式,表明和确认系统功能在各种运行决策、人机交互和外部环境中的变化。它针对系统级功能静态、动态特性进行结构化分析和设计,系统性地研究外部对象、应用用例、功能逻辑、交联时序和状态跳转,在确认模型的合理性后生成逻辑架构与接口,将设计需求进行分配,用于设计实现和软硬件架构。该研究通过对飞行导引、自动推力、自动着陆、机组通告等功能的可用性和完整性进行分析检验,改进了功能需求设计。     

对偶型最大熵概率密度函数模型及其优化解法

针对经典型最大熵概率密度函数模型及其计算目前存在的非线性程度高,优化不收敛,求解效率低等问题,提出了一种对偶型最大熵概率密度函数模型+逐次优化的方法.根据优化过程不稳定,重新推导了拉格朗日系数的线性变换公式.针对几种常见及一种复杂的概率密度函数,采用经典型与对偶型最大熵概率密度函数模型分别计算概率密度及可靠度的对比表明:与经典型最大熵概率密度函数模型相比,对偶型最大熵概率密度函数模型优化函数形式简单,非线性程度低.逐次优化法求解拉格朗日系数不仅克服了初始值敏感性问题,而且计算效率高.对偶型最大熵概率密度函数模型+逐次优化法与其他方法相比,计算精度最高,且能很好的应用于复杂概率分布及可靠性问题.      

基于功能危险性评估的民用飞机驾驶舱门设计探讨

FAA分别于2002年和2008年颁布25-106及25-127修正案,增加驾驶舱门安保事项以提高驾驶舱的安全水平。修正案要求加固驾驶舱门,驾驶舱门必须设计成可以阻止未被授权人员进入驾驶舱并且阻碍危险物体射入以保证机组人员的安全。驾驶舱门必须能检测驾驶舱失压并可以释放门或者卸压板平衡压力差,还应有措施使飞机机组成员在该舱门卡住的情况下能直接从驾驶舱进入客舱。因此,在驾驶舱门上设有一个可以快速释放的紧急出口。根据飞机驾驶舱门结构及功能的主要特点,对驾驶舱门功能故障进行探讨,同时对功能故障引发的危险性等级进行划分,以确定安全指标,进而辅助驾驶舱门设计工作。     

商用飞机驾驶舱造型设计特征研究

介绍了国内外商用飞机驾驶舱设计的历史及现状,在分析多类飞机驾驶舱造型设计图片资料的基础上,探讨主要飞机制造商驾驶舱造型设计的特征。依据驾驶舱造型的相似性,对国际上12家商用飞机制造商的66款机型的驾驶舱进行聚类分析和多维尺度分析,挑选出10款有代表性的驾驶舱。在提取代表性驾驶舱造型特征线后,分析主要飞机制造商的驾驶舱造型设计特点及差异,为新型飞机驾驶舱造型设计提供参考。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Practical compensation for nonlinear dynamic thrust measurement system

The real dynamic thrust measurement system usually tends to be nonlinear due to the complex characteristics of the rig, pipes connection, etc. For a real dynamic measuring system,the nonlinearity must be eliminated by some adequate methods. In this paper, a nonlinear model of dynamic thrust measurement system is established by using radial basis function neural network(RBF-NN), where a novel multi-step force generator is designed to stimulate the nonlinearity of the system, and a practical compensation method for the measurement system using left inverse model is proposed. Left inverse model can be considered as a perfect dynamic compensation of the dynamic thrust measurement system, and in practice, it can be approximated by RBF-NN based on least mean square(LMS) algorithms. Different weights are set for producing the multi-step force, which is the ideal input signal of the nonlinear dynamic thrust measurement system. The validity of the compensation method depends on the engine’s performance and the tolerance error0.5%, which is commonly demanded in engineering. Results from simulations and experiments show that the practical compensation using left inverse model based on RBF-NN in dynamic thrust measuring system can yield high tracking accuracy than the conventional methods.     

基于不相关模态振型的修正技术

为充分利用试验测量结果,探讨了一种修正技术,不但有效利用试验数据中与有限元模型相关的模态信息,同时也有效利用不相关模态信息,并成功应用于某型现代高推质比涡扇发动机结构中.通过计算,修正后的模型计算值与试验测试值比较接近,误差接近0,MAC（model assurance criteria）值接近1.研究表明:利用不相关模态振型的模型修正技术能够有效得到准确的修正参数值,且修正后的有限元模型具有很高的计算精度.