发动机进排气效应对民机构型气动特性影响

基于非结构混合网格技术,通过数值求解Navier-Stokes方程,分析了航空发动机进排气效应对民机构型气动特性的影响。通过设置合适的进排气边界条件来模拟发动机进排气效应的影响,采用单独发动机短舱风洞试验模型,验证了计算方法的可靠性。在此基础上,分析了发动机进排气效应对翼吊式和尾吊式两种典型民机构型气动特性的影响,结果表明:翼吊式民机构型发动机进排气效应对升力的干扰主要由发动机尾喷流的引射效应对机翼的干扰引起;尾吊式民机构型随着发动机进气流量的增大,机翼上表面压力逐渐减小,激波位置逐渐后移;不同发动机进气流量会对飞机的阻力特性产生较大影响,在飞机详细设计阶段需充分考虑机体与动力装置之间的干扰影响。      

三角翼大幅度俯仰运动非定常测压实验洞壁干扰研究

用两个几何相似大小不同的前缘后掠角 70°三角翼模型在闭口风洞中进行正弦俯仰振荡实验 ,测量三角翼模型吸力面动态压力以及风洞洞壁上最佳测压点的非定常压力。实验表明 ,三角翼模型在正弦俯仰振荡时 ,其吸力面动态压力以及洞壁上最佳测压点的非定常压力与三角翼模型上的法向力一样呈现迟滞环现象。模型展宽比 (翼展 /洞宽 )增大 ,迟滞环幅度增大 ,动态压力绝对值增大。无论上仰或下俯 ,模型展宽比 (翼展 /洞宽 )增大 ,三角翼模型吸力面涡破碎位置离前缘较远。风洞顶壁上最佳测压点非定常压力迟滞环方向与风洞底壁上对应最佳测压点非定常压力迟滞方向相反。风洞洞壁上最佳测压点非定常压力变化频率与模型正弦俯仰振荡频率一致 ,各最佳测压点间呈现时间延迟现象。     

Effects of synthetic jet frequency on the separated flow in a diffusing S-duct

Numerical simulations were carried out to investigate the effects of synthetic jet actuation frequency on the separated flow in a diffusing S-duct. The Reynolds number based on the entrance height was 9.78×105. At first, the numerical model was validated with experimental data, and then, the interaction between the separated flow and the synthetic jets at different frequencies was discussed. The results demonstrate that the control effect is significantly dependent on the momentum mixing enhancement between inside of the separated boundary layer and the outer flow. There exists a narrow range of actuation frequency, in which effective separation control can be achieved using synthetic jets. A dimensionless frequency F+=1.0 is identified as the optimal frequency, with a momentum coefficient of 1.62×10-3, the separation area is reduced about 46%, and the aerodynamic performance of the S-duct is also greatly improved compared to uncontrolled case. Further analysis reveals that the choice of actuation frequency is mainly determined by the momentum flux produced by a single ejection and the spacing between adjacent ejections, the optimal frequency case can be understood as a balance between the two factors. In addition, it is found that the synthetic jets can also suppress the secondary flows while decreasing the separation.      

高速风洞模型支撑方式研究

为了合理选择模型支撑形式,在高速风洞进行了直支杆与Z 支杆两种支撑形式的支架干扰研究试验。结果发现,支架对模型带来不可忽略的干扰量,两种支撑形式对升力、阻力与力矩的干扰量随迎角基本上呈线性变化;直支杆由于距离模型较近,对模型尾部带来较大的影响。而Z 支杆对模型尾部影响较小,在全机与无尾两种状态下的干扰量较为相近。     

高超声速导弹等离子体合成射流控制数值研究

快响应控制技术已成为高超声速飞行器发展的关键技术之一,具有极快响应、零质量特性的等离子体合成射流(PSJ)已在超声速流动控制方面初步显示出优异的控制能力,极有潜力应用于高超声速飞行器的快响应控制。基于等离子体合成射流的快响应特性,提出了高超声速飞行器等离子体合成射流快响应控制技术,并通过建立简化的高超声速导弹流场控制模型,对等离子体合成射流控制高超声速导弹进行数值研究。首先,理论分析了高超声速导弹流场的典型结构特征,导弹流场中存在3个特征流场结构。在此基础上,在导弹3个特征位置前面安装等离子体合成射流激励器,研究等离子体合成射流对高超声速流场结构的控制作用,分析由此导致的导弹表面压力分布、升阻特性以及俯仰力矩特性变化。数值仿真结果表明:等离子体合成射流对高超声速导弹外流场中膨胀波和斜激波都具有控制作用,使得波的强度均变弱,且对斜激波的控制效果更为显著;导弹流场结构及气动特性变化具有很强的射流跟随性,射流作用下的导弹流场变化响应时间非常短,仅为0.2 ms;通过合理布置等离子合成射流激励器的位置,可以使得导弹表面压力分布快速改变,从而实现高超声速导弹姿态的快速控制。     

分开排气式喷管喷流噪声预测及试验研究

为揭示涡扇发动机分开排气式喷管喷流噪声的频谱分布和指向特性,对喷管缩比模型远声场喷流噪声进行了预测及试验研究,并开展了全尺寸喷管基准型及锯齿型喷流噪声的预测工作。结果表明:采用Tam & Auriault方法可以预测出喷流噪声的声压级值和空间指向分布,喷流噪声具有明显的指向性。与基准型喷管相比,锯齿型喷管具有良好的降噪效果;内外涵锯齿型喷管在中低频段的降噪效果优于内涵锯齿型喷管,在高频段的降噪效果差于内涵锯齿型喷管;在本文研究参数范围内,指向角小于88°时内外涵锯齿型喷管总声压级(OASPL)值高于内涵锯齿型喷管。     

航空燃油类型对催化惰化系统性能的影响

在设计了一种催化惰化系统流程并描述其工作原理的基础上,以从油箱中抽吸气体的摩尔流量为基准,推导了流经催化反应器后各气体组分的流量关系,通过质量守恒方程及气体平衡溶解关系,建立了油箱气相空间气体浓度变化的数学模型。选择了RP-3、RP-5和RP-6燃油作为对象,用所建立的数学模型计算了不同载油率和催化反应器效率下的气相空间氧浓度变化关系。研究显示,由于3种燃油的蒸汽压不同,造成从外界环境补气及进入油箱的混合惰气流量不同,从而导致气相空间氧浓度的变化规律差异远大于采用中空纤维膜的机载惰化系统。因此,在设计催化惰化系统时要充分考虑燃油类型对惰化系统性能的影响。     

低马赫数下多凹腔燃烧室非稳态燃烧过程

作为稳定火焰的有效手段之一,凹腔构型在冲压发动机燃烧室研究中占有重要地位。在对以煤油为燃料的多凹腔燃烧室冷/热态流动特性分析的基础上,重点研究低进口马赫数条件下燃烧室点火起动初期非稳态过程。结果表明：上游凹腔内大涡结构有助于提高燃料的驻留时间,未燃混气被高速主流带入下游凹腔内继续反应,进一步提高燃烧效率;燃油喷射速度决定被卷吸进回流区的燃油质量分数的大小,进而影响燃烧效率高低;燃烧室点火起动初期出现了主流熄火、火焰逆流传播以及主流再着火等复杂现象,火焰逆流传播现象是在上游凹腔内燃料自燃与下游燃烧释热压缩来流两种机制共同作用下完成的。     

Design and implementation of rigid-flexible coupling for a half-flexible single jack nozzle

The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uni-form flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aero-dynamic design methods of an expansion wall and machinery implementation plan for the half-flexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigid-flexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard (GJB).     

火花放电合成射流与超声速来流相互干扰特性数值模拟研究

为了指导火花放电式合成射流激励器在超声速流动控制中的应用,数值模拟研究了火花放电合成射流与超声速来流的相互干扰特性。研究表明火花放电式合成射流在超声速流场中产生强烈扰动,产生较强的激波结构;随着射流的喷出,激励器上游分离区和流场中激波呈先增强后减弱的趋势,激波由弓形激波逐渐弱化为斜激波,并且随着放电能量的增加射流与主流的动量通量比不断增大,射流的干扰和控制能力显著增强。由于超声速流的较大惯性及其对腔内气体的引射作用,激励器的腔体回填速率大幅下降、回填时间明显增长,使得激励器的工作频率受到很大限制。