肋条结构对气膜冷却凹槽叶尖流动换热的影响

为有效抑制涡轮转子叶尖泄漏并改善叶尖热负荷,采用数值模拟的方法,对5种叶尖肋条结构的高压涡轮带气膜冷却突肩叶片流场进行计算,评估了不同叶尖肋条结构的气热性能.结果 表明:在叶尖增加肋条结构能够有效调控叶尖空腔涡、刮擦涡、肋后涡和冷气肾形涡的路径,从而起到减小叶尖高表面传热系数区,提高叶尖平均气膜冷却效率的作用,同时有效...     

A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

The verification of GNSS tropospheric tomography model in a mountainous area

The GNSS (Global Navigation Satellite System) has not been developed as a meteorological data source provider, but with a careful and sophisticated processing strategy it might be used as one. The term GNSS tomography refers to the usage of the ray traced GNSS signal as scanning rays in the tomographic model input. The model is divided into a number of voxels. The system is inverted and value of refractivity is obtained. Typically, as in the most of the inverse processing, there is a problem of the undetermined system and as a consequence the cofactor matrix is close to singular. To avoid singularity additional conditions or constrains should be added to the system. Here, additional parameters are derived with the help of the air flow analysis in the Sudety mountains (south-west region of Poland), and special Slant Wet Delay (SWD) trimming procedure. The flow’s synthetic parameters like the Bruint-Väisälä frequency and the Froude number are determined. This way the type of the flow is recognized and the analysis of the impact of orographic barrier has been quantified. The SWDs from the GNSS observations were tested against, SWD from raytracing through the COAMPS model field. The modified GNSS tomography model was tested for the real GNSS observations delivered from the GNSS network Karkonosze located in the Sudety mountains and compared with the COAMPS model. The solution shows a considerable improvement in comparison with plain tomographic model results.     

涡轮流量计前导流件有限元计算分析

对涡轮流量计关键部件之一前导流件运用NX THERMAL/FLOW进行有限元计算分析,得出流量分离导致的大涡旋尾迹区易出现在前导流件尾部区域、前导流件叶片形状对此处流体速度变化具有较大影响的结论,为涡轮流量计和前导流件的设计提供了理论依据。     

基于非结构网格的不可压N-S方程多矩有限体积法

提出了一种基于三角形及四面体非结构网格的有限体积法(FVM),用以鲁棒且精确地求解不可压粘性流动问题.与传统的FVM方法仅将体积分平均值(VIA)作为计算变量的做法不同,本文提出的方法将VIA及点值(PV)同时作为计算变量并在每个迭代步进行计算更新.VIA以通量形式进行计算以确保数值守恒,PV可以通过控制方程的不同形式进行求解更新,无需守恒,因此可以采用非常高效的方法进行求解.将PV作为增加的变量使得紧致网格模板得以实现更高阶精度的重构,而且由此获得的数值模型对于非结构网格变得更鲁棒.本文针对二维/三维的三角形/四面体非结构网格提出了数值格式,给出了几个基准测试算例,验证了本文提出的数值方法在采用非结构网格求解不可压粘性流动问题时的精确性和鲁棒性.     

基于功能脆弱性的空中交通相依网络流量分配

依据空中交通管理与航班运行规则,采用复杂网络理论构建由机场、航路与管制扇区组成的相依网络模型,建立不同扰动策略的影响规则,提出以网络流量熵和交通流损失比变化率为指标识别网络功能脆弱性。并以网络总流量熵最小为目标,建立基于改进遗传算法的网络流量协调分配策略,以降低空中交通相依网络的脆弱性。以民航华北地区空域为原型,发现了其相依网络脆弱性表现规律和脆弱源,采用遗传算法求解网络流量分配方案,优化结果降低了网络总熵值和功能脆弱性,其中机场网络流量分配后效果最为显著,验证了方法的有效性,研究结果可为空中流量管理决策提供一定的理论支撑。     

“蚌式”进气道附面层扫除特性风洞试验

以某低、高速风洞为平台,设计搭建了“蚌式”进气道附面层扫除特性测量试验系统,进行了不同流量系数和来流马赫数下进气道鼓包表面附面层扫除特性的风洞试验,通过对试验数据的整理、计算和对比分析同型号的飞行试验结果,研究了“蚌式”进气道鼓包表面附面层扫除特性。研究结果表明:在相同的来流马赫数下,随着流量系数的增大,鼓包表面附面层的扫除能力逐渐减弱;在亚声速工况的绝大多数流量范围内,鼓包表面压力系数沿鼓包中心线对称分布、压力梯度变化明显,且在不同截面沿主流方向具有增大的特征,鼓包构型对附面层扫除效果较强;超声速工况下具有明显附面层扫除能力的流量范围明显小于亚声速工况,进气道唇口形成的弓形激波是影响鼓包表面不同位置压力梯度变化的主要因素,进而决定着附面层扫除特性。在接近来流马赫数18及以上飞行工况下,附面层的扫除能力减弱,附面层分离加强,进而会造成较大的进气压力损失和畸变。     

0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

脉冲爆震燃烧室出口燃气能量分布特性

为了提高脉冲爆震燃烧室出口燃气能量转换效率,采用数值计算方法,研究了带气动阀和爆震增强结构的脉冲爆震燃烧室出口燃气能量分布特性,结果表明:脉冲爆震燃气的膨胀过程先后经历一次膨胀、二次膨胀和过度膨胀3个阶段,单个周期内二次膨胀阶段的时间和能量占比最大;燃烧室出口燃气压力势能、动能、内能和能流密度的分布主要受燃气压力的影响,且变化规律与燃气压力一致;一次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的479%、259%、251%;二次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的502%、576%、581%。     

火星大气来流模拟装置CFD仿真与试验

根据我国火星着陆巡视器工作过程,其着陆发动机需要在相对火星大气高速迎风运动中可靠点火。由于巡视器着陆时发动机喷管出口气流与火星稀薄气流方向相反,目前无法通过理论计算准确获得着陆过程的动态流场对发动机起动过程的影响量值。为验证火星着陆环境下发动机点火的适应性,需要建立发动机的火星大气来流试验环境模拟条件。为模拟发动机在火星大气条件下的相对运动,在真空舱内发动机保持固定,前端设置环形来流形成装置,该装置在发动机喷管周围形成一定速度的逆向来流包络。采用数值模拟技术结合试验验证方法,在火星着陆器巡视器主发动机性能考核试验中,针对来流的形成装置开展了设计研究工作。来流模拟试验测试数据表明:在确保贮箱供应压力稳定的条件下,来流模拟系统能够形成100~200 m/s速度的稳定来流,发动机在来流下能稳定启动工作,真空舱压力满足试验要求。