国外航空涡扇发动机涡轮叶片热障涂层技术发展

介绍了美国等国家开发的航空发动机涡轮叶片热障涂层技术及其应用情况,并总结了该技术的发展动向,旨在为中国开展相关研究和应用工作提供参考和借鉴.     

一种涡轮发动机加速控制规律设计的新方法

 提出了一种涡喷、涡扇发动机加速控制规律快速设计的新方法：在发动机稳态特性计算模型的基础上,通过额外增加转子提取功率,使得发动机稳态工作点（线）靠近喘振边界,在同时考虑燃烧室富油熄火边界、涡轮进口总温限制以及压气机喘振裕度限制的条件下,利用适当的控制规律描述形式并结合发动机工程研制中的经验,能够快速而准确地获得涡喷、涡扇发动机加速控制规律。对某型涡喷发动机加速控制规律的改进的计算结果表明,提出的加速控制规律的设计方法准确而有效。     

某燃气轮机试车中振动值渐增故障分析

某型燃气轮机在长试过程中发生压气机测点振动值逐渐增大,而涡轮截面测点的振动值无明显变化的现象.结合采取的排故措施,对支承刚度变化、联轴器不对中以及膜片联轴器对整机振动响应的影响规律进行了计算和试验验证,对故障原因进行了分析,认为振动异常的主要原因是整机支撑结构发生松动,进而导致联轴器不对中.     

基于卡尔曼滤波器及神经网络的发动机故障诊断

提出了一种基于卡尔曼滤波器及神经网络的航空燃气涡轮发动机气路故障诊断的方法.该方法用卡尔曼滤波器来估计发动机可测参数的变化量,再由神经网络来映射发动机性能参数的变化量,并据此进行发动机气路故障诊断.数字仿真表明,该方法是可行的,有效的.      

用于微型涡轮机的节流孔式静压气浮轴承实验

对用于厘米级微型涡轮发动机的径向静压气浮轴承展开了实验研究,分析了长径比、节流孔径、气膜间隙及供气压力等对承载力、刚度和耗气量的影响.提出了这些设计参数的优选方法,并结合直径11 cm的某微型喷气发动机,给出了与之匹配的径向静压气浮轴承设计方案:工作面直径15 mm、长度17.5 mm、节流孔径0.35 mm、气膜间隙25μm.此方案在供气绝对压力2.5 kPa时,双轴承支撑能力为13.72 N,耗气量小于1.0 g/s,有效地满足了微型涡轮发动机要求.      

民用发动机污染排放及低污染燃烧技术发展趋势

针对民用发动机污染排放的现状,介绍了低污染燃烧技术发展概况及趋势,国际民航组织(ICAO)颁布的《航空发动机的排放》标准,以及中国民用航空局(CAAC)对排气污染物的规定,分析了排气污染物的生成机理和主要影响因素以及改善措施.对6种先进低污染燃烧室(分级、变几何、催化、贫油预混预蒸发燃烧室(LPP)、富油燃烧/淬熄/贫油燃烧技术(RQL)以及双环预混旋流(TAPS)等燃烧室)的工作原理与特点、以及应用状况作了简要分析.其中分级燃烧技术构成了先进低污染燃烧室设计的技术基础,而LPP,RQL与TAPS燃烧室为三种很有发展前途的低污染燃烧室.此外,还介绍了贫油直接喷射、燃料电池以及主动燃烧控制等三种新型的低污染燃烧技术,虽然实现这些技术难度较大,但有广阔的应用前景.      

飞行器级间段跨声速脉动压力特性试验

通过脉动压力风洞试验测量，对比分析了跨声速（马赫数介于0.75~1.2）不同锥角和锥长大小的级间段对锥柱外形飞行器局部脉动压力的影响规律。结果表明，肩部脉动压力主要由以低频为主导的激波振荡所致，能量集中在100 Hz左右的窄带区间，且表现为随着马赫数增加，脉动压力系数峰值先增大后减小，并随着肩部激波的后移而不断向后推移。此外，通过对比分析5种不同锥角模型（10°、12.7°、15.3°、20°、25°）的脉动压力系数最大值发现，随着锥角的增加，脉动压力表现出当锥角小于15°时先平缓增加，随着锥角增大脉动压力系数增加幅度进一步加大的趋势。对比分析不同锥长模型的结果发现，锥长对局部脉动压力的最大峰值几乎没有影响，影响的只是脉动压力在肩部作用区域的大小以及峰值出现的马赫数范围，且表现为锥柱级间段越长其作用范围越大，对应于峰值的马赫数区间越宽。     

带三棱锥体群通道流动和传热特性的数值模拟

对带有三棱锥体群的涡轮叶片内部冷却通道进行了数值模拟,对比了三棱锥体群在迎风和背风状态、顺排和交错排列以及不同横向列数、不同流向间距时冷却通道内部的流动和传热特性。结果表明:三棱锥体群所产生的纵向涡能够兼顾压损的降低与传热效果的改善;背风顺排状态放置的三棱锥体群具有最高的综合传热效率,较其他放置方案高出20%~30%;在背风顺排时,较优横向列数为5,流向间距比为4~6。     

Experimental study on NOx emission correlation of fuel staged combustion in a LPP combustor at high pressure based on NO-chemiluminescence

Experimental investigations on NO_x emissions of a single-cup, Lean Premixed Prevaporized (LPP), module combustor were carried out at elevated inlet temperature and pressure up to 810 K and 2.0 MPa, close to the real operating conditions of aero-engine combustors. This LPP combustor adopts centrally staged fuel injections which could produce separated stratified swirling spray flame. In the NO_x emissions measurements, the ranges of dome equivalence ratio and fuel stage ratio were from 0.55 to 0.58 and 8% to 24%, respectively. The optical diagnosis on separated stratified swirling spray flame were carried out with fuel stage ratio changing from 15% to 30%. Therefore, NO* and OH* chemiluminescence images were obtained. The results show that NO_x emissions increase with the increase of the fuel stage ratio. And from the chemiluminescence images, the main flame and pilot flame are found weakly coupled. The pilot flame plays a significant role in NO_x emission production because of its higher adiabatic flame temperature. Based on the results of chemiluminescence optical tests, a new NO_x emission prediction model is proposed based on the Lefebvre’s single flame model. The estimate of local equivalence ratio of the pilot stage’s non-premixed flame is modified considering the characteristics of spray combustion, and a “PLUS” emission prediction model suitable for separated stratified swirling spray flame is obtained. Compared to the experimental data, the “PLUS” model exhibits a good prediction in a range of ±13% of deviation.     

A wall-thickness compensation strategy for wax pattern of hollow turbine blade

As an important index affecting the aerodynamic performance and the structural strength of hollow turbine blades, the wall-thickness precision of the blade is mainly inherited from the positional relationship between the corresponding wax pattern and the internal ceramic core. However, due to locating errors, the actual position of ceramic core is always deviated from the ideal position, which makes it difficult to guarantee the wall-thickness precision of the wax pattern. To solve this problem, a wall-thickness compensation strategy is proposed in this paper. Firstly, based on the industrial computed tomography (ICT) technique and curve matching algorithms, a model reconstruction method is developed, with which the 3D model of a trial wax pattern can be easily constructed. After that, focusing on eliminating the wall-thickness errors of the trial wax pattern, an optimization method for the pose of the ceramic core in the wax pattern is proposed. Then, by mapping the optimal pose of the ceramic core to length adjustments of the locating rods, the wall-thickness errors of the wax pattern can be greatly reduced. A case study is also given to illustrate the effectiveness of the proposed compensation strategy.