棘爪扁簧断裂故障分析及制造工艺的改进

通过设计计算、对比分析、工艺复装、工艺试验等方法对棘爪扁簧使用中断裂故障进行了分析,并针对性地从设计、工艺两方面进行了改进,经鉴定与试车验证,措施有效,为航空发动机同类零件的研究提供了经验。     

某发动机调节器自动检测异常故障分析

针对某型发动机自动调节器自动检测异常的故障现象,对产生发动机自动调节器自动检测异常的原因进行了深入地研究分析,并提出了针对性的预防措施。     

DME Interference mitigation for L-DACS1 based on system identification and sparse representation

L-band digital aeronautical communication system 1 (L-DACS1) is a promising candi-date data-link for future air-ground communication, but it is severely interfered by the pulse pairs (PPs) generated by distance measure equipment. A novel PP mitigation approach is proposed in this paper. Firstly, a deformed PP detection (DPPD) method that combines a filter bank, correlation detection, and rescanning is proposed to detect the deformed PPs (DPPs) which are caused by mul-tiple filters in the receiver. Secondly, a finite impulse response (FIR) model is used to approximate the overall characteristic of filters, and then the waveform of DPP can be acquired by the original waveform of PP and the FIR model. Finally, sparse representation is used to estimate the position and amplitude of each DPP, and then reconstruct each DPP. The reconstructed DPPs will be sub-tracted from the contaminated signal to mitigate interference. Numerical experiments show that the bit error rate performance of our approach is about 5 dB better than that of recent works and is closer to interference-free environment.     

基于改进准则法的复合壳阻尼结构拓扑减振动力学优化

针对复合壳阻尼结构的拓扑减振优化问题，以约束阻尼层的有限单元为设计变量，采用体积比、模态频率和振型为优化约束条件，构建以多模态权重系数的结构模态损耗因子数值关系为优化目标函数的拓扑减振优化模型。为了拓展优化目标灵敏度具有不局限于某一变密度法插值模型的形式，推导了数值表达式的一般函数式。动力学优化中优化目标灵敏度正、负数集共存，使得非凸性的目标函数设计变量出现负值或优化函数寻优于局部极值点。为此，推导出复合壳阻尼结构的全域灵敏度改进优化准则法迭代格，以确保每次迭代域均为全域设计变量集。结合有限单元法编程实现了复合壳阻尼结构改进准则法，并对复合壳结构进行拓扑减振优化分析。结果表明：在敷设体积减为全覆盖的50%时，复合壳结构的模态损耗因子增减偏差为10%，具有提升减振的轻量化设计目的；各阶目标函数和拓扑构型所需的迭代次数少，中间密度区域较小，多阶优于单阶模态优化函数，易于获得全域寻优的有效减振。     

防烟供氧面罩漏气系数试验系统的设计及应用

介绍了防烟供氧面罩漏气系数试验系统的设计与试验原理。该系统采用单元分体式结构，将气路、油路、机械各部分集成于一体，在软件作用下，通过电气电路，控制油雾的产生，保证油雾发生的流量，控制油雾室浓度的高低，控制取样流量的大小，并通过油雾浊度仪读取检测数据，完成试验过程的自动控制。     

基于人工神经网络的停机坪安全预警研究

停机坪是机场的重要组成部分,停机坪安全是机场安全关注的重点。影响停机坪安全作业的要素有很多,通过对这些要素进行监控和预警,可以减少停机坪的安全隐患,保证机场正常运行。根据济南遥墙机场的主要数据,运用因子分析法对影响停机坪安全的主要因素进行分类,提取公共因子。并运用人工神经网络（ANN）方法,对这些公共因子进行神经网络训练和预测分析,最终得到遥墙机场停机坪的安全情况。     

某型飞机通信电台干扰油量系统故障分析

针对某型飞机通信电台干扰油量系统故障，分析了油量测量系统的原理和电磁干扰机理，研究了故障发生的原因，制定了抑制干扰的措施，解决了一直困扰修理的油量指示系统跳变问题，提高了飞机修理质量。     

Analyses toward factors influencing sealing clearance of a metal rubber seal and derivation of a calculation formula

Sealing clearance is a key factor for a metal rubber seal’s sealability. The expansion coef-ficient and expansion deformation in the radial direction of metal rubber have been obtained through a thermal expansion experiment of metal rubber. The influence of the elastic modulus to the sealing clearance has been analyzed theoretically. By combining the temperature and elasticity factors of metal rubber with the elastic mechanics theory, the calculation formula of the sealing clearance has been derived, and the values of the sealing clearance and the leakage rate in certain working conditions have been calculated. Experimental results are consistent with calculation results in a high degree. The calculation formula of the sealing clearance can explain the influences of the temperature and elastic modulus factors of metal rubber on the sealing clearance. It can pro-vide guidance for the study of sealing mechanism of metal rubber seals.     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

含多部位损伤搭接结构应力强度因子三维有限元分析

应力强度因子(Stress intensity factor,SIF)分析是含多部位损伤(Multiple site damage,MSD)结构剩余强度和裂纹扩展寿命预测的基础和关键。考虑接触与摩擦,建立了含MSD搭接结构的三维有限元模型,研究了不同裂纹长度、铆钉类型以及损伤模式下裂纹尖端SIF分布情况和变化规律。结果表明,搭接件孔边裂纹Ⅰ型SIF起主导作用,Ⅱ型和Ⅲ型SIF可忽略不计。由于次弯曲、铆钉变形和板厚度等因素,SIF在外表面最小,接触面一侧较大,最大值多位于蒙皮内部。MSD会使裂纹间的干涉作用增强,SIF增大,且裂纹间距离越近干涉作用越强。裂纹长度相同时,埋头铆钉的孔边裂纹SIF积分均值大于平头铆钉,且接触面的SIF埋头铆钉大于平头铆钉,外表面则相反。