进气道中激波-边界层干扰特性研究

针对高超进气道中激波/边界层干扰等现象,选取了24°压缩拐角及二维高超进气道DLR-GK01等算例,比较研究了混合网格并行数值模拟软件中SA、SST、TNT三种湍流模型对激波/边界层干扰等现象的模拟能力,主要考察了不同湍流模型对流场结构、壁面压强以及壁面摩阻的影响。结果表明:三种湍流模型在模拟大分离流场时存在不同的流动分离特性,TNT湍流模型较SST和SA湍流模型模拟的分离起始位置、分离区大小及边界层厚度与实验吻合度最好。     

某型飞机进气道有限元应力及振动疲劳分析

针对某型飞机进气道经常出现的蒙皮裂纹、铆钉断裂等现象,通过建立飞机进气道有限元模型,对进气道进行了有限元应力分析及振动疲劳分析。根据分析结果提出了改进方案,通过计算验证、改进方案能有效降低裂纹多发部位的应力水平、增加振动疲劳寿命。     

扑翼非定常气动特性的实验研究

扑翼的动态特性使其具有与固定翼完全不同的飞行模式,为了研究扑翼在扑动周期内的非定常气动特性,建立基于虚拟仪器的扑翼风洞实验测控系统,能够实现对气动力、扑动角度、功率等物理量的实时测量;以斯特劳哈尔数作为扑翼非定常程度的度量标准,并根据斯特劳哈尔数的定义完成扑翼在不同扑动幅度、扑动频率和来流速度条件下的风洞实验;分析扑翼在不同条件下的升力、推力及推进效率,进而得出斯特劳哈尔数对扑翼气动特性的影响规律。结果表明:扑翼的气动力随斯特劳哈尔数的增大而显著增大;当斯特劳哈尔数处于特定范围内时,扑翼具有较高的推进效率。     

高超侧压进气道溢流方案的改进与分析

为了提高高超侧压进气道的性能,通过在其侧板上方添加盖板与在底板开槽的方式对其溢流方案进行了改进.对原型与改型进气道进行了来流Ma =4 ～7流场的数值模拟,并对两进气道进行了Ma =4时不同攻角下的起动性能试验.结果表明,低马赫数时(Ma =4,5),在总压恢复系数基本保持不变的前提下,改型进气道的流量系数较原型进气道获得大幅提升,Ma =4时,提高20.6％,Ma =5时,提高11.5％.在流量系数增加的同时,起动性能也获得大幅提升,来流为Ma =4时,由-2°攻角下起动提升为+4°攻角下依然可以实现起动.由于溢流方案的改进针对低马赫数时的进气道流场,在高马赫数时(Ma =6,7),进气道的性能基本不变.研究表明,抑制侧板间溢流的同时引入底板溢流的方式是提高高超侧压进气道综合性能的有效途径.     

唇口斜切修型对S形进气道RCS影响

采用基于迭代物理光学法与等效边缘电磁流法的雷达散射截面计算程序,分析了水平、垂直两种极化方式下唇口斜切修型对菱形进口S形进气道边缘绕射场及腔体内部散射场的影响。计算结果表明：在水平、垂直两种极化方式下,斜切修型可有效降低边缘绕射场的雷达散射截面,但随斜切角度的增大,其减小幅度降低;正负斜切角度对应的绕射场雷达散射截面分布关于0°探测角对称;斜切修型对腔体内部散射场的影响较小。     

Experimental research in rotating wedge-shaped cooling channel with multiple non-equant holes lateral inlet

The heat transfer in a novel smooth wedge-shaped cooling channel with lateral ejection of turbine blade trailing edge is experimentally investigated in both non-rotating and rotating cases. Beside the conventional inlet at the bottom of the channel, an extra coolant injection from 8 lateral non-equant holes is introduced to improve the overall heat transfer. The total mass flow rate ratio (lateral mass flow rate/total mass flow rate) varies from 0 to 1.0. The major inlet Reynolds number and rotation number respectively vary from 10000 to 20000 and from 0 to 1.16. Experimental results show that the lateral inlet decreases local bulk temperature and increases local heat transfer at the middle and the top of the static channel. In rotating cases, the lateral inlet notably improves the heat transfer at the high-radius half channel and compensates the negative effects induced by the rotation. Both intensity and uniformity of heat transfer inside the channel are enhanced while flow resistance decreases with proper mass flow rate ratio of coolant from two inlets. The most satisfactory total mass flow rate ratio is around 2/3. This new structural style of cooling channel has huge potential and provides new direction of heat transfer of turbine blade trailing edge.     

Design method with controllable velocity direction at throat for inward-turning inlets

In the design of a hypersonic inward-turning inlet by applying the traditional basic flowfield, a reflected shock-wave is formed in the isolator due to the continuous reflection of the cowlreflected shock wave in the basic flow-field, which interacts with the boundary layer to produce a considerable influence on the performance of the inlet. Here, a basic flow-field design method that can control the velocity direction at the throat section is developed, and numerical simulations are conducted to demonstrate the effectiveness of this method. The method presented in this paper can achieve the absorption of the reflected waves at the shoulder of the basic flow-field by adjusting the variation law of the center radius in the basic flow-field, and a smooth transition between the compression surface and the isolator can also be produced. The Mach number and total pressure recovery coefficient of the inlet designed according to this method are 3.00 and 0.657, respectively, at design point(the incoming flow Mach number Ma1= 6.0). The results show that with this method, the inlet can efficiently weaken both the reflection of the shock wave and the interaction between the boundary layer and the reflected shock waves, which improves the aerodynamic performance of the inlet.     

Study on effects of thickness on airfoil-stall at low Reynolds numbers by cusp-catastrophic model based on GA(W)-1 airfoil

The phenomena of an airfoil stall present the behaviors of catastrophe and hysteresis at low Reynolds numbers. Numerical simulation results of two-dimensional airfoil GA(W)-1 show that the width of the hysteresis loop of airfoil stall will gradually decrease and even disappear with the decrease of thickness ratio. These nonlinear characteristics are in accordance with the topological features of the cusp catastrophic model. According to the topological invariant principle, a novel topological mapping method is developed to establish the mapping relationship between cusp catastrophic model and stall characteristics of the airfoil, then the effect of thickness ratio on airfoil stall is successfully described quantitatively by cusp catastrophic model. Further, based on the established topological mapping relationship, combined with the mean flow field of the airfoil stall, potential function approach of cusp catastrophic model is first introduced to interpret the catastrophe and hysteresis of the airfoil stall, and it is found that as the thickness ratio decreases, the system's maximal potential energy gradually disappears, and the short separation bubble at the leading edge of the airfoil changes to long separation bubble, so the airfoil stall changes from a bistable system to a monostable system.     

飞机零部件更改管理方法研究

针对飞机研制过程中零部件更改管理问题,分析了国内外的管理模式,提出更为符合技术状态管理要求以及逻辑性更优的管理思路,为今后的飞机研制过程中零部件更改管理提供参考.     

一种基于有限元/边界元耦合方法的管道进口声传播及声辐射模型

本文发展了一种基于有限元和边界元耦合方法的管道进口声传播及声辐射计算模型。该模型将整个声场分为内部有限域和外部无界域,分别用有限元和边界元方法求解控制方程,在二者之间的界面上使用具有物理意义的声阻抗参数进行匹配,并通过一种快速迭代方法实现全声场求解。这种迭代方法可以保证有限元刚度矩阵等带宽以及对称的特性不被破坏,有助于提高计算效率。该模型先得到了Levine and Schwinger标准解的检验,进而在无流动情况下对于简化的航发短舱进口管道模型进行了噪声辐射现象的数值模拟,最后基于计算结果分析了声衬对远场声辐射的影响。