高密度喷气燃料与常规喷气燃料浓度场试验研究

本文利用ＣＯ２红外气体分析仪和取样管对高密度喷燃料和常规喷气燃料在直流喷嘴下游的浓度场分布进行了测量，就气流速度，油压降和下游距离对浓度场分布的影响进行了对比研究。试验结果表明，在相同工况下，常规喷气燃料的最大浓度值比高密度喷气燃料的大；气流速度和油压变化对高密度喷气燃料最大浓度点穿透深度的影响大于对常规喷气燃料的影响。     

热暴露对B/Al复合材料性能的影响

对经300℃、500℃高温热暴露的B／Al（LF6）复合材料的力学性能进行了研究，实验结果表明材料在300℃下热暴露时，性能下降速度较慢，100h后强度保留率约为76％，延伸率保留率为74％。而在500℃下热暴露时，5h以上强度就有明显降低。高温长时间热暴露后复合材料的断裂也从积累型转变为典型的非累积型断裂。通过透射电镜（TEM）及扫描电镜（SEM）对固态热压制造态和主温热暴露的界面状况进行了分析，认为界面反应是造成B／Al复合材料力学性能下降的主要原因。     

基于Solid Works和Cosmos的模具结构三维设计及有限元分析

复杂结构注塑模具的设计和强度、刚度分析是注塑行业的重要难题。利用Solid Works三维设计软件实现了注塑模具的三维实体建模，并运用COSMOS／Works软件对注塑模具的典型部件进行了有限元分析，验证设计的零件是否符合实际工作情况是实现注塑模具现代化设计的重要途径。通过GearTrax2001Plus、Toolbox等外挂、内挂插件的使用．大大地简化了建模过程，克服了原有设计方法的不足．为解决较复杂的结构设计和理论分析问题提供了一种新的途径。     

逆向射流多斜孔气膜冷却的数值模拟

为了使航空燃气轮机燃烧室在高于燃烧室材料许用温度的前提下能够正常工作,需对燃烧室内壁采取冷却措施,并对变吹风比和变角度下的逆向射流多斜孔气膜冷却进行了数值模拟。在贴体坐标下划分网格,采用k-ε模型模拟湍流流动,求解气膜冷却过程的数学模型。分别改变逆向射流同主流的夹角,使其为20°、30°、45°和60,°改变吹风比的变化范围为0.5到1.5等多种条件下,对多斜孔气膜冷却效果进行了数值模拟。在所研究的范围内得到了符合规律的结论。研究结果表明,当吹风比不变的情况下,减小逆向射流角度,用有效温比表示的冷却效果相应提高。当逆向射流角度不变时,增加吹风比,冷却效果也相应提高。     

TC21钛合金的微观组织对力学性能的影响

研究了两相钛合金TC21关于两种不同微观组织(片状组织和网篮组织)的拉伸性能、断裂韧性和疲劳裂纹扩展性能.结果显示:片状组织相比网篮组织有相近的拉伸强度,但塑性较差;两者的韧性相差不大,但增韧机理不同;网篮组织在中低速扩展区的扩展速率和片状组织几乎相同,但在较高速扩展区显示略低的扩展速率;加载方向对两种组织的疲劳裂纹扩展速率基本无影响;和其他钛合金类似,TC21在Paris区存在转折.     

腰形柱壳的有限条元解

本文用考虑了曲率影响的两结线低阶有限板条元分析了腰形柱壳的力学性能这种条元位移参数少,能较好地体现壳体的几何特性。     

A novel surrogate modeling strategy of the mechanical properties of 3D braided composites

In this paper, a surrogate-based modeling methodology is developed and presented to predict the elastic properties of three dimensional (3D) four-directional braided composites. Using this approach, the prediction process becomes feasible with only a limited number of training points. The surrogate models constructed using Finite Element (FE) method and Diffuse Approximation, reduce the computational time and cost for preparing experimental samples. In the FE model, multiscale method is applied to couple the computations of elastic properties at microscale and mesoscale. Subsequently, a parametric study is performed to analyze the effects of the three design parameters on the elastic properties. Satisfactory results are obtained via the surrogate-based modeling predictions, which are compared with the experimental measurements. Moreover, the predictions obtained from surrogate models concur well with the FE predictions. This study orients a new direction for predicting the mechanical properties based on surrogate models which can effectively reduce the sample preparation cost and computational efforts.     

Effects of process parameters on mechanical properties of abrasive-assisted electroformed nickel

A cathode mandrel with translational and rotational motion, which was supposed to obtain uniform friction effect on surface, was employed in abrasive-assisted electroforming for revolving parts with complex profile. The effects of current density, translational speed and rotational speed on the deposit properties were studied by orthogonal test. The tensile strength, elongation and micro hardness value were measured to find out how the factors affected the properties. The optimized results show that changes of current density affect the tensile strength of nickel layer most, while translational speed has the most remarkable influences on both elonga-tion and micro hardness. The low rotational speed affects the properties least. In this experiment, a smooth nickel layer with tensile strength 581 MPa, elongation 17%and micro hardness 248HV is obtained by the orthogonal test.     

某型航空活塞发动机曲轴喷油螺钉的维修工艺研究

喷油螺钉是某型航空活塞式发动机曲轴组合中的重要零件，单纯采用超声波清洗难以清除该零件内部积炭。结合生产实践对工艺进行改良，使该零件修理后的抽检合格率由20%提升至70%，缩短了发动机的翻修时间，节约了维修成本。     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。