气相二氧化硅/汽油凝胶燃料流变特性实验研究

为了较为全面地了解凝胶燃料的流变特性,采用超声波振荡与机械搅拌相结合的方法制备了含铝与不含铝的气相二氧化硅/汽油凝胶燃料,使用旋转流变仪实验研究了各凝胶燃料的剪切变稀特性、触变性、屈服应力与粘弹性等流变参数。结果表明:气相二氧化硅/汽油凝胶燃料具有明显的剪切变稀特性和不可逆触变性。凝胶剂含量增加,凝胶燃料粘度和屈服应力增大。添加10μm粒径铝粉的粘度和屈服应力比5μm粒径铝粉的大,比1μm粒径铝粉的小,但均比不含铝凝胶燃料的大。凝胶燃料在低频振荡下更接近于流体,在高频振荡下具有类固体特征。      

旋转条件下大长径比固体火箭发动机三维内流场数值模拟

根据燃面的平行层推移原理,获得了某大长径比固体火箭发动机装药燃面变化过程。采用有限体积法计算了发动机在旋转飞行状态下的三维稳态流场,着重分析了不同时刻药柱开槽部分和燃烧室尾部的流速、流迹分布及其对发动机正常工作的影响,认为发动机尾部热防护以及药柱悬臂段强度是保证其正常工作的关键因素。     

Delaying stall of morphing wing by periodic trailing-edge deflection

Morphing wings can improve aircraft performance during different flight phases. Recently research has focused on steady aerodynamic characteristics of the morphing wing with a flexible trailing-edge, and the unsteady aerodynamic and stall characteristics in the deflection process of the morphing wing are worthy further investigation. The effects of the angle of attack and deflection rate on aerodynamic characteristics were examined, and based on the aerodynamic characteristics of the morphing wing, a method was developed to delay stall by using the flexible periodic trailing-edge deflection. The numerical results show that the lift coefficients in the deflection process are smaller than those in the static situation at small angles of attack, and that the higher the deflection rate is, the smaller the lift coefficients will be. On the contrary, at large angles of attack, the lift coefficients are higher than those in the static case, and they become larger with the increase of the deflection rate. Further, the periodic deflection of the flexible trailing-edge with a small deflection amplitude and high deflection rate can increase lift coefficients at the critical stall angle.     

Experimental Study of Corner Stall in a Linear Compressor Cascade

In order to gain a better knowledge of the mechanisms and to calibrate computational fluid dynamics (CFD) tools including both Reynolds-averaged Navier-Stokes (RANS) and large eddy simulation (LES),a detailed and accurate experimental study of corner stall in a linear compressor cascade has been carried out.Data are taken at a Reynolds number of 382 000 based on blade chord and inlet velocity.At first,inlet flow boundary layer is surveyed using hot-wire anemometry.Then in order to investigate the effects of incidence,measurements are acquired at five incidences,including static pressures on both blade and endwall surfaces measured by pressure taps and the total pressure losses of outlet flow measured by a five-hole pressure probe.The maximum losses as well as the extent of losses of the corner stall are presented as a function of the investigated incidences.     

应急液压堵头在A320飞机上的应用

从A320系列飞机液压系统的原理入手,分析了在A320飞机上使用应急液压堵头的可行性,详细介绍了如何使用应急液压堵头以及航空公司为预防突发性油液渗漏故障所采取的措施.     

From geometry to CFD grids—An automated approach for conceptual design

The CEASIOM software developed in the EU-funded collaborative research project SimSAC generates stability and control data for preliminary aircraft design using different methods of varying fidelity. In order to obtain the aerodynamic derivatives by CFD, the aircraft geometry must be defined, computational meshes generated, and numerical parameters set for the flow solvers. An approach to automation of the process is discussed, involving geometry generation and mesh generation for inviscid as well as RANS flow models.     

Transonic aeroelastic simulation for instability searches and uncertainty analysis

In this paper the use of eigenvalue stability analysis of very large dimension aeroelastic numerical models arising from the exploitation of computational fluid dynamics is reviewed. A formulation based on a block reduction of the system Jacobian proves powerful to allow various numerical algorithms to be exploited, including frequency domain solvers, reconstruction of a term describing the fluid-structure interaction from the sparse data which incurs the main computational cost, and sampling to place the expensive samples where they are most needed. The stability formulation also allows non-deterministic analysis to be carried out very efficiently through the use of an approximate Newton solver. Finally, the system eigenvectors are exploited to produce nonlinear and parameterised reduced order models for computing limit cycle responses. The performance of the methods is illustrated with results from a number of academic and large dimension aircraft test cases.     

高超声速激波/边界层干扰流动数值模拟研究

在基于Roe格式的全Navier-Stokes方程计算流体力学(CFD)代码中,发展了一种局部熵修正方法,克服了传统熵修正方法在边界层流动模拟中耗散过大的缺点,可用于更加准确的模拟激波/边界层干扰的复杂高超声速流动。对典型高超声速双锥边界层分离与激波干扰的复杂流动进行了模拟,研究了网格密度和熵修正方法耗散性对计算结果的影响。研究表明:高超声速双锥边界层分离与激波干扰流动的数值模拟结果对网格具有很强的敏感性,过稀的网格将产生严重的分离流动预测偏差;低耗散性的局部熵修正方法能更加准确地模拟复杂的高超声速激波与边界层分离流动干扰现象。     

基于CFD技术的高效叶栅耦合颤振分析方法

为了考虑叶轮机叶片结构与流体之间的耦合效应,同时提高叶轮机颤振数值研究的效率,发展了一种基于非定常气动力降阶模型(ROM)的叶栅耦合颤振分析方法。该方法运用时域计算流体力学(CFD)技术计算少数几个叶片的非定常气动力,通过系统辨识及一些假设构建整个叶栅振动的非定常气动力降阶模型,并在状态空间耦合叶栅结构动力学方程建立叶栅气动弹性方程,采用特征值和时域仿真分析该系统稳定性。运用该降阶耦合方法对STCF4(Standard Test Configuration 4)以及NASA Rotor67叶栅系统的稳定性进行了计算。通过与直接计算流体力学/计算结构动力学(CFD/CSD)耦合方法和非耦合方法计算结果的比较验证了该方法的准确性,且该降价耦合方法的计算效率相对于直接CFD/CSD耦合方法提高了1~2个量级,为叶轮机气动弹性参数研究、失谐研究以及多模态耦合计算等提供了便利。     

基于浸入式边界方法的运动物体声辐射数值模拟

为了在声学计算中简化网格的处理,从而发展出适用于运动复杂边界问题模拟的计算格式,基于浸入式边界方法,提出了一种适用于无黏流动、无穿透边界条件的处理方法,并对一些简单的运动物体声辐射问题进行了数值模拟.数值结果与解析解得到了令人满意的对比,初步验证了所提出的研究方案的可行性.