Improvement on shaped-hole film cooling effectiveness by integrating upstream sand-dune-shaped ramps

A numerical investigation and experimental validation is performed to address deeper insights into the combined effect of shaped holes and Sand-Dune-shaped upstream Ramp (SDR) on enhancing the film cooling effectiveness, under a wide blowing ratio range (M = 0.25–1.5). Three kinds of holes (Cylindrical Hole (CH), Fan-Shaped Hole (FSH), and Crater-Shaped Hole (CSH)) are taken into consideration. The SDR shows an inherent affecting mechanism on the mutual interaction of jet-in-crossflow. It aggravates the lateral spreading of cooling jet and thus improves the film cooling uniformity significantly, regardless of film-hole shape and blowing ratio. When the blowing ratio is beyond 1.0, the combined effect of shaped holes and SDR on improving film cooling effectiveness behaves more significantly. It is suggested that FSH-SDR is a most favorable film cooling scheme. For FSH-SDR case, the spatially-averaged film cooling effectiveness is increased monotonously with the increase of blowing ratio, among the present bowing ratio range.     

冕洞特征参数与重现型地磁暴关系的统计研究

在提取冕洞特征参数的基础上,利用1996年到2005年8月近十年来对地磁扰动有影响的356个冕洞事例,定量分析了冕洞特征参数(包括冕洞的面积比、经纬度跨度等)与冕洞高速流特征、重现型地磁扰动特征(包括扰动大小和持续时间等)之间的相关性,研究发现,从引起地磁扰动的冕洞在整个太阳活动周的分布来看,在地磁扰动峰年中冕洞影响同样具有重要的贡献;冕洞高速流太阳风速度与地磁扰动强度之间存在较强的相关性,而高速流中太阳风速度与冕洞面积比关系不大,与冕洞亮度存在一定相关性;冕洞的经度跨度与地磁扰动持续时间存在很强的正相关性.      

构建实例库的参数模型及其应用

通过分析系统模型和IDEFO模型,提出了实例参数模型,即将切削系统的各组成参量分成4类:非控制参量,过程参量,控制参量和输出参量并以此提出了实例库的构建过程.最后根据提出的参数模型,建立了高速切削数据库系统.     

涂层刀具低温铣削SiCp/Al复合材料表面质量研究

在加工过程中,相反的两相特性增加了 SiCp/Al复合材料加工难度,难以获得良好的表面质量.为了提高其切削性能,本文开展20vol％SiCp/Al复合材料铣削加工试验研究,比较常温和低温条件下TiAlN涂层和TiAlSiN涂层两种铣刀的切削性能.结果表明,在低温条件下,两种刀具的切削力增加,铣削后表面铝基体的开裂及剥落...     

Elliptical vibration cutting of large-size thin-walled curved surface parts of pure iron by using diamond tool with active cutting edge shift

Large-size thin-walled curved surface parts of pure iron are crucial in aerospace, national defense, energy and precision physical experiments. However, the high machining accuracy and surface quality are difficult to achieve due to the serious tool wear and deformation when machining the parts with conventional cutting tools. In this paper, an elliptical vibration cutting (EVC) with active cutting edge shift (ACES) based on a long arbor vibration device is proposed for ultra-precision machining the pure iron parts by using diamond tool. Compared with cutting at a fixed cutting edge, the influence of ACES on the EVC was analyzed. Experiments in EVC of pure iron with ACES were conducted. The evolutions of the surface roughness, surface topography, and chip morphology with tool wear in EVC with ACES are revealed. The reasonable parameters of ultra-precision machining the pure iron parts by EVC with ACES were determined. It shows that the ACES has a slight influence on the machined surface roughness and surface topography. The diamond tool life can be significantly prolonged in EVC of pure iron with ACES than that with a fixed cutting edge, so that high profile accuracy and surface quality could be obtained even at higher nominal cutting speed. A typical thin-walled curved surface pure iron part with diameter ∅240 mm, height 122 mm, and wall thickness 2 mm was fabricated by the presented method, and its profile error and surface roughness achieved PV 2.2 μm and Ra less than 50 nm, respectively.     

微织构刀具对钛合金切屑形成影响的仿真研究

针对微织构刀具对钛合金Ti6Al4V切屑形成以及微槽二次切削机理分析的不足，通过建立热-力耦合仿真模型对比研究不同微织构刀具、微织构几何尺寸以及切削速度对切屑形成的影响规律。数值仿真结果表明：微织构刀具更有利于断屑，二次切削作用使切屑的弯曲半径变大，微织构可以减小刀屑之间实际接触面积，降低切削温度。增大微织构宽度可以增强微槽的二次切削作用，利于断屑，但应注意其对刀具强度的削弱作用，而增大相邻微槽间距则会出现相反的二次切削作用机制。提高切削速度对各刀具均有利于断屑，弧形微织构刀具的降温效果最好，V形微织构刀具次之，矩形微织构刀具降温效果最差。研究结果对进一步理解微织构刀具对钛合金切屑的二次切削作用机理提供一定参考。     

超声振动辅助切削对碳纤维增强树脂复合材料面下损伤影响的仿真研究

碳纤维增强树脂基复合材料（CFRP）在传统加工（OC）过程中存在着切削力过大、表面质量不佳、面下损伤较为严重等问题。为了改善上述问题，本文提出使用超声振动辅助切削（UVC）工艺加工CFRP，通过仿真分析对切削力与面下损伤深度进行研究。结果表明：使用UVC加工CFRP可降低13%~80%的切削力，且纤维方向角对切削力影响较小。与OC相比，UVC切削0°、45°纤维方向角的CFRP时可以减少约50%的面下损伤深度；在切削90°、135°纤维方向角的CFRP时虽然没有改善面下损伤深度，但取得了较为平整的已加工表面以及较小的损伤区域。