旋转对管内流体流动的影响

本文描述了旋转管流的基本运动方程。在笛卡尔坐标系和柱坐标系中,针对两种基本的几何流动,推导出旋转情况下管内的流动方程,定义了影响旋转管流的流动和换热的两个无量纲准则数J和Ra,分析了二次流产生的原因,从而说明旋转对流动的影响以及旋转管流的运动特征。     

预移相型恒温热线(膜)流速计的动态响应方程

分析传统恒温热线热膜流速计(简称 HWFA)动态方程后,提出了一种新型HWFA 线路模型——主电桥预移相模型,推导出真实条件下小扰动动态响应方程,并按此原理设计制造了崭新的高性能 IFV—900型 HWFA 样机。该机全部革除了传统HWFA 的三个调节参量,大大地简化了调节步骤;不自激振荡的范围明显增宽,极大地减少了使用上的麻烦;频带宽度比当今世界流行的 HWFA 增宽了2～5倍;加上一系列智能化功能后使自动化程度达到了新的高度。这一新型 HWFA 的问世将可能导至 HWFA技术的重大改进和新的变革。首先阐明主电桥预移相模型的提出和真实条件下小扰动动态响应方程的推导。随后将用若干姐妹篇阐明动态方程频率响应调节元物理值的解析解,频率特性实验分析手段的电扰动试验响应情况的理论分析等内容。     

Tear Resistance of Orthogonal Kevlar-PWF-reinforced TPU Film

This work seeks to investigate the notch sensitivity and fracture behaviour of orthogonal Kevlar-plain woven fabric (PWF)-reinforced thermoplastic polyurethanes (TPU) film applied to high altitude balloon. Four types of specimens are implemented to measure notched strength and fracture toughness by conducting static tension and tear tests on an MTS system respectively. The damage and failure mechanisms are discussed and the results for notched strength and tear resistance are evaluated and compared with each other. From the experiments, it is found that the notch sensitivity of the film increases with the increase in the size of the hole, but the notch sensitivity and the stress concentration of the notch are insignificant and there is a decrease of only about 4%-10% in tensile strength for the notched specimens with different hole sizes in diameter compared with the unnotched specimen. In contrast, the tear resistance containing a central slit with only 1 mm length is about half of tensile strength of the unnotched film, which implies that the tear resistance exists an significant notch sensitivity. The results of this study provide an insight into notch sensitivity and fracture behaviour of the Kevlar-PWF-reinforced TPU film and constitute a fundamental basis for the design of high altitude balloon.     

帆板控制系统设计

该帆板控制系统采用塑料薄膜电位器作为传感器检测角度信号,检测到的角度信号经信号处理电路送12位的串行接口A/D转换器ADS7818进行数字化转换,转化结果由Cortex-M3处理器LM3S615进行处理产生PWM控制信号,该控制信号经功率VMOS驱动电路实现轴流电扇的速度调节,从而实现帆板角度定位闭环控制。通过按键可以实现帆板角度的设定及运行控制,设置六位LED数码管显示实现角度及其它运行状态的显示。经过实际测试该系统完全达到了设计要求的各项指标要求。     

Thermal-structural analysis of regenerativelycooled thrust chamber wall in reusable LOX/Methane rocket engines

To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Struc tural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter γ3 =0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when γ3 ＞ 0.The results of sen sitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.     

突片作用下气膜冷却效率的试验研究

为了研究突片对气膜冷却的影响规律, 设计了3种不同堵塞比的等边三角形突片, 并对其对气膜冷却特性的影响规律进行了实验研究.研究结果表明, 与无突片的气膜冷却相比, 突片的存在提高了气膜冷却效果;冷却效率随吹风比的增加而增大, 且沿气流方向冷却效率存在一极大值;当吹风比M<1.5时, 冷却效率随吹风比的增加而增大;当M>1.5时, 冷却效率随吹风比的增加而减小.      

基于伴随非等温射流理论的缝槽气膜冷却模型

在伴随非等温射流基础上发展了一种适用于缝槽气膜冷却绝热温比预估的数学模型.通过合理假设推导出二维壁面射流混合层核心温度分布规律,将其作为气膜绝热壁温,并考虑缝槽几何特征参数和气膜吹风比对冷却效率的影响,得到绝热温比计算公式.用试验数据对该预估模型进行拟合分析,得到了与试验数据拟合精度在±8%以内的半经验预估模型,证明该模型的可行性和应用潜力,并需要更多的试验数据对其进行验证和改进.      

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

改进的翼型积冰数值模拟方法

基于微团概念,以雨滴运动的基本假设出发,对翼型积冰的拉格朗日方法进行了改进.新方法克服了原方法计算效率低、冰形同雨滴分布密度及网格密度相关的缺点,继承了原方法的鲁棒性,不存在欧拉方法的收敛性问题.为验证方法的正确性,计算了NACA0012翼型在0°和4°攻角下的霜冰积冰情况、表面水收集量和局部撞击系数.结果表明新方法减少了计算量,预测的冰形和实验结果一致,并分析了积冰对气动性能的影响.      

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.