尖侧缘机身布局的俯仰力矩特性及扰流板控制

针对尖侧缘机身布局在大迎角下存在的正俯仰力矩（抬头力矩）问题,通过风洞试验,首先研究了俯仰力矩的迎角分区特性及流动演化规律：线性增长区（迎角为0°~15°）,俯仰力矩线性增加,全机从附着流到形成进气道前缘涡和机翼涡;非线性增长区（迎角为17.5°~32.5°）,俯仰力矩非线性增加,机头涡出现,机头涡和进气道前缘涡逐渐增强,机翼涡增强后破裂;衰减区（迎角为35°~65°）,俯仰力矩逐渐减小,机头涡增强后破裂,进气道前缘涡破裂发展,机翼涡完全破裂。其次,发现了机身前体是产生正俯仰力矩的主要来源,机头涡是导致大迎角下正俯仰力矩的主控流动。当迎角为40°时,前体各截面正俯仰力矩在进气道前缘处达到最大,主要是由于该处机头涡诱导产生了较强的法向力。最后,提出了大迎角机身扰流板控制技术,产生了较好的控制效果。当迎角为40°时,扰流板可使正俯仰力矩减少62%,其原因是扰流板降低了机头涡涡量及其诱导产生的法向力,减少了机身前体对正俯仰力矩的贡献。该控制技术的缺点是扰流板会带来一些升力损失和附加阻力。基于尖侧缘机身参考宽度的雷诺数为2.59×10⁵。     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

直升机旋翼桨叶的弹性碰撞动力学建模

建立了直升机旋翼桨叶弹性正碰撞的动力学模型,采用有限转动梁理论处理桨叶的弹性变形,利用Hertz接触理论处理局部弹性变形,引入位移协调方程识别弹性碰撞载荷,运用Hamilton原理建立了桨叶正碰撞的动力学方程.通过与Timoshenko算例的对比表明了该方法的正确性,且对集中质量与直升机桨叶的弹性正碰撞问题进行了研究.      

弹用S弯进气道气动性能试验

对一种弹用S弯进气道进行了试验,结果表明:①偏航角一定,攻角由负到正变化时,总压恢复系数先上升后变化不大,|DC₆₀|则先下降后小幅升高;②攻角一定,总压恢复系数和|DC₆₀|随偏航角的增加均呈先升高后降低的趋势;③大的攻角和偏航角组合状态下,总压恢复系数较低,|DC₆₀|偏大,但随偏航角进一步增大,进气道性能有所改善;④进/发匹配点处,进气道出口压力功率频谱较平坦且对姿态角和来流马赫数的变化均不敏感;⑤发动机小流量状态时,进气道模型发生了喘振,频率约为150 Hz.      

无轴承开关磁阻电机平均悬浮力控制策略

 无轴承开关磁阻电机是一个复杂的非线性系统,因此其控制策略的研究非常重要。高速时由于反电势的增加,使悬浮绕组开通时刻电流难以跟踪,导致瞬时悬浮力难以控制,因此有必要研究基于平均悬浮力和平均转矩的无轴承开关磁阻电机控制策略。根据无轴承开关磁阻电机的悬浮原理和数学模型,设计平均悬浮力和平均转矩的控制策略。主绕组电流和悬浮绕组电流均采用方波控制。推导了平均悬浮力与绕组电流之间的关系,以及主绕组电流和悬浮绕组电流的计算公式。给出了超前角和绕组电流的计算流程。针对12/8结构的无轴承开关磁阻电机,设计了以数字信号处理器TMS320C2812为核心的控制系统。通过实验给出了绕组电流波形和转子位移波形。实验结果显示了电机的稳定悬浮,验证了此控制策略的可行性。     

对地观测卫星成像调度的多目标约束修正方法

 约束修正是对地观测卫星成像调度的重要组成部分,负责处理成像调度方案的约束满足与优化,是一类复杂的组合优化问题。为得到优化可行的成像调度方案,提出一种新的约束修正方法。针对约束修正问题构建时间序有向图模型,并将约束修正问题归结为点带约束成本的优化路径搜索问题;在此基础上,提出一种基于标记更新的多目标约束修正算法。实际问题的实验与分析表明：该方法能够在规定的时间内求得问题所有的多目标优化解,有效地解决了卫星成像调度的约束满足与优化问题。     

旋翼气动提前操纵角研究

为了保证某型直升机操纵系统设计的顺利进行,本文基于国内外相关资料对气动提前操纵角进行了深入的研究,得出该角度主要取决于桨叶挥舞基阶固有频率ωβ1.而ωβ1与挥舞铰外伸量e、桨叶根部弹性约束Kβ和挥舞调节系数Kp密切相关.通过分析e,Kβ和Kp对气动提前操纵角△ψ的影响,推导出计算该角度的具体公式.采用该公式对几个型号进行计算,经校核与验证后,表明本文提供的计算方法可行,能满足工程精度,可应用于工程研究,从而为布置助力器提供理论依据.     

Foreign Object Damage to Fan Rotor Blades of Aeroengine Part Ⅱ： Numerical Simulation of Bird Impact

Bird impact is one of the most dangerous threats to flight safety. The consequences of bird impact can be severe and, therefore, the aircraft components have to be certified for a proven level of bird impact resistance before being put into service. The fan rotor blades of aeroengine are the components being easily impacted by birds. It is necessary to ensure that the fan rotor blades should have adequate resistance against the bird impact, to reduce the flying accidents caused by bird impacts. Using the contacting-impacting algorithm, the numerical simulation is carded out to simulate bird impact. A three-blade computational model is set up for the fan rotor blade having shrouds. The transient response curves of the points corresponding to measured points in experiments, displacements and equivalent stresses on the blades are obtained during the simulation. From the comparison of the transient response curves obtained from numerical simulation with that obtained from experiments, it can be found that the variations in measured points and the corresponding points of simulation are basically the same. The deforming process, the maximum displacements and the maximum equivalent stresses on blades are analyzed. The numerical simulation verifies and complements the experiment results.     

锯齿冠的结构特性与设计

根据锯齿冠结构原理,导出了包含锯齿冠结构特性参数（λ、ψ、βμ、Δβ）的关系式,即锯齿冠结构特性方程,并将其图解成锯齿冠结构特性曲线,直观、清晰地描述了各特性参数之间的关系和变化规律;揭示了由实际条件产生的“紧度偏差”,论述了锯齿冠结构的设计方法。同时指出,选择过大的接触角会使叶冠失效而引发叶片故障。