某风扇/增压级非设计点性能计算及进气畸变影响分析

在原流线曲率法程序的基础上, 增加了适用于高速风扇/压气机的双激波损失模型.真实地反映了高速风扇/压气机的实际工作状况, 提高了预测高速风扇/压气机非设计点性能的准确性, 完善了分析进气畸变对风扇/压气机性能及稳定性影响的准三维计算模型.针对一台外涵转子叶尖马赫数大于1.4的大涵道比风扇/增压级, 计算分析了其非设计点性能以及进气畸变的影响.计算结果与试验结果吻合较好, 精度可靠, 可应用于工程实际.      

A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.     

航空泵试验台驱动变结构控制

飞机液压系统泵源需进行地面试验,采用变频调速器＋异步电机＋增速箱的驱动形式是航空泵进行地面试验最先进有效的方法之一.建立了矢量控制变频调速驱动下航空泵试验台驱动系统的数学模型,针对航空泵试验时由于负载变化泵转速不能保持恒定的问题,采用积分滑模面的滑模变结构控制策略,并构造Lyapunov函数证明其稳定性.为降低输出抖振现象,提出采用模糊控制监督下的滑模变结构控制和伪微分反馈(PDF, Pseudo Derivative Feedback)控制相结合的控制策略,仿真及实验结果表明,该控制方法有很高的控制精度,在保持滑模变结构控制鲁棒性强的前提下降低了输出抖振现象.      

双独立闭环复合液压伺服控制体系的分析

针对现有几种液压伺服控制系统的优缺点,基于高性能和节能这一发展趋势,提出基于伺服电机、定量泵、蓄能器和伺服阀的双独立闭环的新型复合控制体系.分析了其结构特点,建立了数学模型并进行了仿真分析和实验验证,证明新型控制体系充分发挥了各个控制环节的效能,实现了流量适应,较现有的控制方案简单可靠,在综合指标方面有了很大的提高,适合机载液压系统和弹载液压系统.      

单向电永磁作动器结构优化与动态特性分析

针对电磁作动器的使用要求,设计出一种具有能耗低、吸力大及响应快等特点的新型单向电永磁作动器。结合有限元仿真软件,利用有限元法研究作动器的结构参数如铁芯齿形结构、平面结构、无永磁结构、铁芯的倾斜角度及衔铁位移（气隙厚度）等因素对作动器电磁吸力和响应速度的影响。结果表明,电磁吸力随着作动衔铁位移的增加而大幅度减小;倾角结构的铁芯设计能使作动器性能达到最佳,且铁芯的倾斜角度为50°时,电磁吸力有最大值3071N。     

超磁致伸缩作动器小回线动态J-A模型

超磁致伸缩作动器（GMA）输入输出之间存在着磁滞非线性关系,当研究其中高频输出特性时,为了降低材料自身迟滞非线性特性的影响,往往选用零点与饱和状态之间线性度较好的不饱和小回线,因此很有必要开展动态不饱和小回线数学模型的研究。首先在综合研究磁致伸缩材料（GMM）和GMA结构动力学特性的基础上结合安培环路定理提出以励磁电流为输入、应变为输出的动态Jiles-Atherton（J-A）模型,然后在引入磁滞回线特性变量的基础上得出J-A模型关键模型参数对其特性的影响规律,根据不饱和小回线仿真与实验波形的偏离特性提出模型参数的修正方法得到不饱和小回线动态J-A模型。最后,在不同频率和不同饱和幅值下通过实验验证该数学模型的正确性。      

ANALYSIS OF AN ELECTROSTRICTIVE STACK ACTUATOR FOR ACTIVE TRAILING EDGE FLAPS

Helicopter is a complex dynamic system withmany rotating components. The rotor blades oper-ate in a highly complex aerodynamic environment.The vibratory hub load,which is caused by cyclicvariation ofcentrifugaland aerodynamic load of therotating bladesin flight,is transmitted to the fuse-lage,resulting in serious vibration and noise of thestructure. It is one of the most important excitingsources in helicopters.There has long been a desire to reduce heli-copter vibration and to improve its per…     

Numerical investigation of effect of a centrifugal boost impeller on suction performance of an aircraft hydraulic pump

An integrated boost impeller can effectively improve the suction performance of an aircraft hydraulic pump (AHP). It must be designed very carefully; however, few studies thus far have investigated boost impellers. To explore the effect of the boost impeller, this study developed a three-dimensional computational fluid dynamics (CFD) model for an AHP based on the k-ε turbulence model and full cavitation model. The results of verification tests demonstrated that the model is reliable for simulating the delivery characteristics of piston pumps and the boost capacity of the inlet impeller. Steady-state simulations reveal that the boost impeller can remarkably improve the suction performance and mitigate the cavitation damage due to insufficient fluid filling while only consuming a small proportion of the total input power. Transient-state simulations show that the pump with an impeller is more capable of catching up with a sudden increase in flow demand, and it has a lower suction flow ripple and impact. However, such a boost impeller also has some limitations such as magnifying the suction pressure fluctuation and having little effect on mitigating the cavitation caused by the back-flow jet.     

航空母舰液压拦阻系统拦阻力建模与仿真

以国内外普遍使用的某型航空母舰液压拦阻系统为研究对象,从其组成和工作原理出发.针对产生拦阻力的主要元器件,根据液压系统的传动基本理论建立了液压拦阻系统的拦阻器系统和滑轮缓冲系统的数学模型.利用该模型结合舰载机着舰动力学模型和拦阻索动力学模型进行了拦阻动力学的数值仿真,对比了仿真值与试验值的区别,分析计算了某型舰载机以不同重量、速度着舰的拦阻动力学过程.验证了滑轮缓冲系统能有效减缓拦阻索张力,且通过改变控制阀口通油面积可以实现不同质量飞机在基本相同的距离上实现安全拦阻,说明模型的合理性.     

液压泵摩擦副可靠性设计基本方法研究

阐述了液压泵摩擦副可靠性分析及设计的基本步骤和原则。作为实例,文中给出了滑靴耐磨可靠性设计所采用的（pv）应力模型新方法。