短舱进气道热气防冰系统传热特性研究

为了研究短舱笛形管热气防冰系统中防冰腔设计参数对进气道唇口表面传热特性的影响，进行了不同设计参数下进气道防冰腔内外流域和固体域的耦合仿真传热计算。分析得出了不同射流孔孔径和射流孔到进气道前缘表面的距离等参数对进气道唇口表面的温度、对流换热系数和Nusselt(Nu)数分布的影响。分析结果表明：射流孔直径和射流孔到唇口表面距离在一定的范围内，进气道蒙皮表面温度和对流换热系数随射流孔直径的增大而升高，随中间排射流孔到唇口表面距离的减小而升高。     

制备工艺对W-10Ti合金组织的影响

制备了W-10Ti合金，研究了冷等静压（CIP）压力、热等静压（HIP）温度、高温处理对W-10Ti合金组织的影响。发现CIP能明显提高装料密度，有利于后续的HIP成形和元素扩散。提高CIP压力和HIP温度，能提高W与Ti扩散程度，HIP在1 300 ℃时，纯Ti相完全消除。高温处理温度为1 300、1 400、1 500、1 700 ℃时，富Ti相含量先降低再升高，在1 400 ℃时降至最低，为5.18%。在超过1 400 ℃处理时，富Ti相会发生共析转变。     

基于AMESim的热气防冰系统笛形管设计与仿真

笛形管是飞机热气防冰系统的重要组成部分，笛形管上的孔径、孔间距以及笛形管的引气入口参数决定了防冰供气流量的大小及分配，从而影响防冰性能。本文基于多学科系统建模仿真平台AMESim，建立了笛形管流量分配仿真分析模型，对机翼热气防冰系统笛形管结构参数进行迭代设计。设计参数包括笛形管管径、喷孔孔径及孔间距等参数，最终获得了能够平衡设计状态点防冰热载荷的结构参数和引气流量分配，得到了防冰系统的引气压力制度。本文提出的基于AMESim的笛形管迭代设计方法可为热气防冰系统中笛形管的设计与优化提供参考。     

先驱体转化─热压烧结法制备C_f/SiC复合材料

以Y2 O3-Al2 O3和MgO -Al2 O3为烧结助剂体系 ,研究了烧结助剂体系及其含量对Cf/SiC复合材料密度与力学性能的影响。结果表明 ,以Y2 O3-Al2 O3为烧结助剂时 ,复合材料的力学性能优于烧结助剂为MgO -Al2 O3时复合材料的力学性能。当烧结助剂为Y2 O3-Al2 O3时 ,随着烧结助剂含量的增加 ,复合材料力学性能不断提高 ,断裂韧性在烧结助剂含量为 12 %时达到最大值 14.83MPa·m1/ 2 。进一步增加烧结助剂的含量 ,复合材料的抗弯强度虽有提高 ,但断裂韧性急剧降低。烧结助剂含量超过 15%后 ,抗弯强度也急剧降低。结果同时证明 ,复合材料的断裂行为取决于纤维 /基体间的界面结合强度 ,即纤维 /基体间的界面结合情况是决定纤维增强陶瓷基复合材料力学性能的关键因素     

Hot Tearing Behavior of Mg-Gd-Y-X Alloys

Mg-Gd-Y-Zr alloy castings are widely used in the aerospace field owing to their high strength and excellent creep resistance. The castability of these alloys is also an important consideration for engineering application. Thus， the hot tearing susceptibilities (HTSs) of Mg-10Gd-1Y-1Zn-0.5Zr (VW91) alloy and Mg-10Gd-2Y-1Zn-0.5Zr (VW92) alloy are investigated with a constrained rod casting (CRC) mold. The microstructures and fracture surface are characterized by optical microscope and scanning electron microscope. The results unveil that the HTS of VW92 alloy is lower than that of VW91 alloy. The microstructures indicate that obvious tears can be observed in VW91 alloy， while the tears in VW92 alloy are tiny. The tear feeding and healing by eutectic are also observed in VW91 and VW92 alloys. Therefore， the lower hot tearing susceptibility of VW92 alloy is mainly attributed to the high amount of eutectic which feeds and heals tears. Besides， the effects of the coefficient of thermal expansion (CTE) and the fluidity of VW91 and VW92 alloys on their HTSs are discussed.     

TA15粉末冶金产品热等静压成形工艺过程的数值模拟

针对高品质粉末冶金新产品的研发,为了减少其研发周期、降低试验成本,采用Marc模拟软件,对轴承座产品的热等静压近净成形过程进行了有限元数值模拟。结果表明:经工艺成形后,产品几何外形尺寸变化较大,相对密度整体达到0.98,局部尖端位置相对密度仅为0.85,对此提出了改进包套结构和芯模结构形式、局部增加装粉量等方案,提高局部位置致密度,保证产品整体质量,为产品的实际生产提供了理论指导作用。     

Microstructure and Hot Deformation Behavior of Mg-9Al-3Si-0.375Sr-0.78Y Alloy

Using Gleeble-3500 thermal simulator， the high temperature plastic deformation behavior and microstructure evolution of Mg-9Al-3Si-0.375Sr-0.78Y alloy are investigated at the temperature of 523 K?673 K and the strain rate of 10-3 s-1?10 s-1. True strain-true stress curves show the characteristics of the typical dynamically recrystallization process. The Arrhenius constitutive equation of the hyperbolic model is established. The average activation energy and the strain rate sensitivity index are， respectively， 221.578 kJ.mol-1 and 0.137. The result shows that the α-Mg phase exhibits dynamic recrystallization (DRX) characteristics obviously. But no DRX occurs in theβ-Mg17Al12 phase. Hot deformation does not affect the primary Mg2Si phase. Under the conditions of low temperature (523 K?673 K) and high strain rate (1 s-1?10 s-1)， the flow instability and macro-defects such as crack appear in the specimens. However， there are finer recrystallization grains. Under the conditions of high temperature (≥673 K) or low strain rate， the microstructure of the alloy shows good homogeneity. The size of the primary Mg2Si phase is uniform， the size of the β-Mg17Al12 phase is small， and the distribution of the β-Mg17Al12 phase is uniform.