纺丝工艺对炭纤维缠绕复合材料强度转化率的影响

通过不同纺丝工艺的聚丙烯腈基炭纤维表面状态、NOL环及Φ150 mm容器的实验研究,分析了不同纺丝工艺对湿法缠绕复合材料聚丙烯腈基炭纤维强度转化率的影响。结果表明,干喷湿纺炭纤维比湿法纺丝Φ150 mm容器环向纤维强度转化率要高出11.9%~15.4%,湿法纺丝的炭纤维复合材料NOL环层间剪切强度要比干喷湿纺炭纤维复合材料高7.4~34.1 MPa。因此,干喷湿纺的炭纤维可应用于固体火箭发动机缠绕壳体、压力容器等主要承受拉伸应力的领域,可充分发挥其纤维强度;而湿法纺丝工艺制成的炭纤维与树脂基体结合紧密,利于载荷的传递,可应用于承受压缩剪切等复杂载荷的领域,从而发挥这两种纤维各自不同优势。     

进气道堵盖打开过程数值模拟

为获得整体式固冲发动机转级过程中进气道堵盖(包括入口堵盖与出口堵盖)打开过程的流动形态,建立了进气道二维模型,利用Fluent动网格技术和UDF方法,开展了进气道堵盖打开过程非稳态流场研究。结果表明,在入口堵盖打开前,进气道前端形成强烈的弓形激波;在入口打开、出口未开的过程中,沿进气道轴向各监测点压强呈现周期性变化,振荡频率为100 Hz左右,出口堵盖位置压强振荡幅值为0.53 MPa;在出口打开后,补燃室残余热量形成的压强峰导致进气道在短时间内无法起动,随着背压降低至小于进气道再起动反压,进气道完全起动。     

Laser-induced oxidation assisted micro milling of high aspect ratio microgroove on WC-Co cemented carbide

Severe tool wear and poor surface quality are the main problems during micro machining of cemented carbide. In this work, an innovative hybrid process of laser-induced oxidation assisted micro milling (LOMM) was proposed to solve the problems. A nanosecond laser was utilized to induce oxidation of the WC-20%Co material, producing loose oxide which was easy to remove. The micro machinability of the material was improved by laser-induced oxidation. The oxidation mechanisms of cemented carbide were studied. A microgroove with a depth of 2.5 mm and aspect ratio of 5 was fabricated successfully. The milling force, surface quality and tool wear mechanisms were investigated. For comparison, a microgroove was also fabricated with conventional micro milling (COMM) using identical milling parameters. Results revealed that in LOMM the milling force and tool wear rate were extremely low during removing the oxide. The machined surface quality and dimensional accuracy achieved by LOMM were superior to those obtained by COMM. The surface roughness S_a of the microgroove bottom reached 88 nm in LOMM, while the cross-sectional geometry of the microgroove was a trapezoid. Perpendicularity of the microgroove sidewall machined by LOMM was better than that by COMM. The tool wear forms in LOMM were coating spalling and slight tool nose breakage. Compared with COMM, the tool life in LOMM was prolonged significantly. It indicates that the proposed hybrid process is an effective and efficient way to fabricate high aspect ratio micro-features with high dimensional accuracy.     

内孔结构对旋转空化发生器水力特性的影响

空化普遍存在于工业生产、舰船推进、航空航天等领域.使用高速相机对闭式循环试验台的旋转空化发生器内部流动进行试验观测,然后基于RNG k-s湍流模型和Zwart-Gerber-Belamri空化模型开展了旋转空化发生器流场的数值模拟.结果表明数值模拟结果与试验观测数据吻合较好,验证了本文数值模拟方法的准确性和可靠性.受离...     

雷达侦察环境信号密度量化研究

在分析现代雷达侦察环境信号特点基础上,提出了以时域、空域、频域和功率域参数为参变量的雷达侦察环境信号密度量化参数——环境信号占空比,并通过理论分析和实验证明了其单调性、稳定性和可测性等基本性质.该量化参数对于测量评估现代战场雷达侦察环境信号密度、构设雷达侦察装备试验所需的复杂电磁环境,具有比较重要的意义.     

Fatigue crack propagation of new aluminum lithium alloy bonded with titanium alloy strap

A new type of aluminum lithium alloy (Al-Li alloy) Al-Li-S-4 was investigated by test in this paper. Alloy plate of 400 mm · 140 mm · 6 mm with single edge notch was made into samples bonded with Ti-6Al-4V alloy (Ti alloy) strap by FM 94 film adhesive after the surface was treated. Fatigue crack growth of samples was investigated under cyclic loading with stress ratio (R) of 0.1 and load amplitude constant. The results show that Al-Li alloy plate bonded with Ti alloy strap could retard fatigue crack propagation. Retardation effect is related with width and thickness of strap. Flaws have an observable effect on crack propagation direction.     

基于循环平稳性的噪声调频干扰高分辨测向方法

根据噪声调频信号循环平稳特性分析,提出了基于阵列接收信号循环均值-空域处理的波达方向(DOA)估计算法。仿真结果表明:该算法的角度估计性能明显高于比幅比相单脉冲测角法,且在高信噪比环境中,该法的估计性能更好、运算量较小。     

大展弦比运输机标模高升力构型设计与评估

介绍了中国航空工业空气动力研究院基于分层策略遗传算法的多段翼型优化设计工具和高升力构型计算评估方法,参照国内外大展弦比运输机指标为FL-9增压风洞设计了高升力构型标模,为检验标模气动性能,在法国ONERA F1风洞进行了一系列风洞试验和采用UNSMB平台进行了数值模拟。结果显示计算结果与试验结果有着较好的一致性,设计方案具有较好的增升效果。     

基于Kriging模型插值的孔位修正策略

飞机装配时的孔位精度直接影响其最终装配质量，而待制孔零件易发生变形和整体偏移，因此一般通过基准孔信息对待制孔位进行补偿。提出一种基于Kriging插值的孔位修正方法，通过基准孔建立孔位理论坐标与实际偏差值的Kriging模型，进而预测待制孔的孔位偏差，并给出每个位置的预测标准误差，以指导基准孔的增添和布置。最后通过有限元和数值实验分别验证了零件在极限变形和整体平移旋转情况下该方法的有效性，实现了孔位估计误差小于0.3 mm。     

Leakage performance of floating ring seal in cold/hot state for aero-engine

Rotating experimental investigations were carried out to study the oil sealing capability of two different floating ring seals in cold/hot state for aero-engine. High-speed Floating Ring Seal(HFRS) is a seal with the inner diameter of 83.72 mm and maximum speed of 38000 r/min, and Low-speed Floating Ring Seal(LFRS) is another seal with the inner diameter of 40.01 mm and maximum speed of 18000 r/min. In hot state, sealing air with the temperature of 371 K and oil with the temperature of 343 K was employed to model the working conditions of an aero-engine. Comparisons between floating ring seal and labyrinth seal were done to inspect the leakage performance.More attention was paid to the critical pressure ratio where the oil leakage began. Results show that the critical pressure ratio in cold state is obviously larger than that in hot state for both seals. An underlying sealing mechanism for floating ring seal is clarified by the fluid film, which closely associates with the dimensionless parameter of clearance over rotating diameter(2 c/Dr). Another fantastic phenomenon is that the leakage coefficient in hot state, not the leakage magnitude, is unexpectedly larger than that in cold state. Overall, the leakage performance of the floating ring seal is better than the labyrinth seal.