电火工品在线检测装置的温度特性

介绍了工程使用中电火工品的检测电路原理图和工作原理,并在高低温状态下对电路进行了性能研究.为满足电路在较大温度范围内的性能指标,根据高低温状态下的实测值调整了电路的门限值,满足了较大温度范围内电火工品的检测.     

边界约束对直升机尾操纵拉杆安装频率影响分析

针对某型直升机在飞行过程中出现脚蹬高频振动问题,通过飞行振动数据分析,确定了故障原因为尾操纵拉杆动特性不佳导致尾操纵拉杆局部共振,从而引起脚蹬高频振动。为了满足装配要求,尾操纵拉杆与安装支座之间为间隙配合,导致尾操纵拉杆边界约束存在不确定性,因此有必要进行边界约束敏感性分析。本文采用弹簧刚度表征尾操纵拉杆边界约束,并基于Ritz法建立尾操纵拉杆理论模型,分析讨论了边界约束对尾斜拉杆安装频率的影响,同时根据计算分析结果提出了相应的解决方案。经地面动特性试验和飞行试验验证,该解决方案可以有效改善该型机脚蹬高频振动问题,同时对后续操纵拉杆设计和分析具有一定的参考意义。     

基于MSC/PATRAN的飞机结构强度静力试验数据实时跟踪与处理系统开发

 在Windows环境下,以MSC/PATRAN为平台,利用平台提供的二次开发语言PCL(Patran Command Language),并结合C++语言,通过客户化、增设特定的命令和窗体等技术开发了飞机结构强度静力试验数据实时跟踪与处理系统TestDTAS（Test Data Tracking, Analyzing and Processing System）。在结构试验进行中,TestDTAS可以实时地监测结构试验件中应力和位移的变化情况,并与理论分析结果进行对比,而在试验结束后,TestDTAS可以进行试验数据回放和分析,从而将试验与理论分析有机的结合在一起,对结构静力试验和结构设计有很高的实用价值。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

机电作动系统发展

 机电作动系统是通过控制电动机或电器的运行直接或间接地控制负载的运动,实现控制目标的位置伺服控制的一类系统的总称。针对飞行器用机电作动系统,概述了其应用概况、结构的演化过程、关键技术的发展过程,并就机电作动系统的发展动态做了介绍。在此基础上,提出了飞行器用机电作动系统的研究和发展的一些建议。     

航空发动机双转子系统的拍振分析

 在双转子航空发动机中,由于转子系统不可避免地存在不平衡量,当两个转子的转速比较接近时,发动机会出现拍振现象,拍振将引起振动强度过大问题。对双转子系统的拍振进行了研究,分析了拍振的周期性、信号强度及其反向转子特性,阐明了拍振产生的机理和特征,并采用数值仿真和试验对拍振进行了定量分析和验证。研究表明,拍振与双转子转速差和不平衡量的相位因素有关,当转速差小于工作转速的20%时,双转子系统拍振信号的强度较大。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

模型烧蚀对尾迹电子特性影响的计算和实验研究

 基于气动物理研究的需要,针对高焓风洞的来流特点,采用计算和实验相结合的方法研究聚丙烯烧蚀对尾迹电子密度的影响。结果表明：计算结果可以有效模拟实验状态,电子密度的模拟精度有很大提高,误差在一个量级内;聚丙烯烧蚀可以降低尾迹的电子密度,但幅度不大,在2倍左右,其与选择模型材料的催化特性降低幅度相当;对电弧风洞的成功改进和非稀薄流静电探针诊断技术的应用,是尾迹电子密度测试的前提保障。     

自动测试系统适配器自动设计技术

 针对当前自动测试系统（ATS）适配器设计中存在的“自动化程度较低、缺乏通用性”的不足,开发了ATS通用适配器自动设计技术。建立了一整套通用适配器自动设计流程,在依次完成通用端口设计、UUT测点资源匹配、适配器开关网络设计、相关工程设计后即可实现自动设计一个通用适配器的目的。以某机载通讯设备自动测试系统为例,采用该技术可缩短ATS适配器开发周期至原来的1/3,降低开发成本,提高设计的标准化、通用化程度,适配器需要量由5个减为1个。     

New Cutting Force Modeling Approach for Flat End Mill

A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions.