一种高灵敏度的电动舵机系统研究

本文研究了一种基于单片机的高灵敏、分体式小型电动舵机系统。首先分析了电动舵机的组成与功能,并分别从舵机结构、控制算法两方面对舵机系统的性能设计进行了分析和阐述。针对舵机高灵敏度的性能要求,对控制算法进行了优化并进行了相应仿真。最后经过试验验证,电动舵机满足了高灵敏度的指标要求,验证了控制算法的正确性。     

一种修正的Osher通量在高阶WCNS中的特性

将一种基于多维修正的Osher通量运用于高阶加权紧致非线性格式(WCNS)中,该修正通量主要在垂直于激波面的界面上增加耗散,能够改善Osher通量的激波捕捉稳定性,同时对边界层和接触间断的分辨率影响非常小。对修正的Osher通量在高阶WCNS中的特性进行研究,通过数值模拟测试了基于Osher通量的WCNS的激波稳定性、热流预测精度、边界层模拟能力、激波边界层干扰模拟能力,并与Steger-Warming通量和Roe通量进行了对比。结果表明修正后的Osher通量比Harten修正的Roe通量具有更好的激波捕捉鲁棒性,而边界层、驻点热流值和激波边界层干扰的模拟则明显优于Steger-Warming通量。上述结果说明了基于修正的Osher通量的高阶WCNS具有较好的激波捕捉特性、热流预测精度和边界层计算能力。     

表面再结晶对定向凝固高温合金高周疲劳行为的影响

采用悬臂旋转弯曲试验,研究定向凝固DZ4合金在喷丸预变形及热处理后产生的再结晶层对高周疲劳寿命的影响.结果表明,DZ4合金经过一定程度的预变形,在随后的高温热处理后表面会产生一定厚度的再结晶;再结晶层对DZ4合金高周疲劳寿命有一定影响;在一定喷丸强度范围内,随喷丸强度增加,疲劳寿命先减小后增大.     

基于切削热-力耦合效应的表面强化技术及其工艺试验研究

经过对超高强度钢工件高速切削加工表面质量的系统研究,发现在某种特定的切削条件下,工件表面质量将会发生显著改变.该变化不仅表现为表面特征的大幅改善,如表面粗糙度可以控制在0.4μm以下,无宏观裂纹发生等,还表现为表层及次表层显微硬度的明显提高、最大残余压应力深度的大幅增加(达到0.35 mm)以及表面耐磨性能的显著增强等.研究结果表明,合理的切削工艺将极有可能成为一种能够在获得工件结构形状与精度指标的同时,对加工表面表层、次表层的组织特性与工件使用性能产生积极影响的表面强化手段.     

Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.      

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

Study on the breakup lengths of free round liquid jets

IntroductionBreakup and atomization of roundliquidjetshad been widely used in internal combustion en-gines,gas turbines,and liquid rocket engines.Recently,with the development of scramjet en-gines and the deepening of fuel atomization re-search,it attract…     

用FTIR光谱仪测量排气系统中红外光谱辐射强度的方法

通过理论分析及实验研究讨论了傅立叶变换红外(FTIR)光谱仪测量排气系统中红外光谱辐射强度过程中误差产生的原因, 设计了一套简易有效的测量方法.用此方法测量了黑体和热喷流的光谱辐射强度.结果表明:该测量方法能够有效地获得排气系统的中红外光谱辐射强度, 具有工程实用价值.      

高灵敏GPS接收机抗干扰特性研究

采用圆环阵列天线,利用最小规范算法和线性约束最小方差算法对弱GPS信号的干扰信号进行了抑制,并分别针对固定和可变天线阵元数目以及固定和可变干扰信号等多种情况进行了仿真和分析.GPS信号的功率电平假设为-175dBW,干扰信号的功率值在-100dBW～-140dBW范围内可变.仿真结果表明,圆环天线阵列能精确地判定干扰信号的来波方向,该方法能很好地改善对来波干扰信号的赋零深度.     

高陡度光学非球面高效制造的探讨

分析了计算机控制光学表面成形法、计算机控制应力盘抛光、磁流变抛光制造光学非球面元件的几项先进技术,探讨了光学元件的高速、高效加工,提出了高陡度光学非球面的固着磨料研磨加工。