Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

水气动量交换的实验研究

在风浪槽中进行水气动量交换实验，测量了不同风速和风区下的波浪及空气湍流流场。测量数据表明水面上风速分布符合对数律，水气界面附近在小范围的动量交换常通量层。阻力系数ＣＤ随风速增加线性增长，随波龄增加而减小。这一趋向与理论分析及外海帝测结果一致。对风浪发展过程中波浪和空气湍流谱结构的分析证明了水气运动的耦合关系。     

小不对称物体配平性能风洞实验研究

用阶跃响应法,在风洞中测量小不对称物体配平性能的实验原理、实验装置、数据处理及部分实验结果。 模型支承于空气静压轴承。在模型内部设有电磁机构,在一次吹风中,可以阶跃方式多次提供不对称量。由高精度、非接触的感应同步器数字测量模型俯仰角变化历程。用修正Newton-Raphson法处理数据,求出小不对称量引起的配平角δ_o、俯仰力矩C_mo和气动刚度C_ma、气动阻尼C_mq等参数。 对11°斜切锥,钝度比分别为0.06及0.16的模型进行了风洞实验。实验M数为33.5和4。实验结果表明,所采用的实验原理、设备及方法可提供较好的精度及分辨率。实验还求出了配平性能(δ_o,C_mo)以及C_ma,C_mq随M数的变化。     

典型CMOS存储器电离辐照效应

对电离辐照环境中典型CMOS存储器的辐照效应进行了研究。分析了SRAM,EEPROM,FLASH ROM存储器在^60Coγ射线辐照及辐照后不同退火过程中,CMOS存储器的集成度、辐照偏置、退火时间和温度与电离辐照效应的关系。结果发现：不加电（冷备份）状态的^60Coγ射线辐照过程中,存储器的逻辑状态翻转出现较正常工作状态推迟1个量级以上;随着集成度的提高,SRAM,EEPROM存储器的辐照敏感度降低;试验器件经不同剂量的^60Coγ射线辐照后在不同温度下退火,所有试验器件均出现了逻辑状态翻转。     

自动转移飞行器的轨控总体方案

介绍了欧空局的自动转移飞行器（ATV）的轨道控制方案和技术。给出了ATV的飞行方案、测量敏感器和执行机构的配置，以及在空间站调相段、寻的段、接近段和最终逼近段的轨控策略。     

铁基金刚石节块的热处理及其耐磨性能研究

首次提出了在烧结型金刚石工具的制造中引入热处理的新工艺，并系统地研究了淬火温度、淬火时间及回火温度等热处理工艺参数对热压烧结型铁基金刚石圆盘锯节块及其胎体材料机械性能的影响，同时对经热处理的铁基金刚石圆盘锯节块在石材旺苍红上进行磨损试验研究。试验结果表明，热压烧结型铁基金刚石圆盘锯节块胎体热处理的最佳工艺参数为：淬火温度为７６０～７９０℃、淬火时间为３．５ｍｉｎ、回火温度为２４５～３１５℃；经热处理后铁基金刚石圆盘锯胎体及节块的强度、硬度等机械性能有显著的提高，热处理也能明显改善铁基金刚石圆盘锯节块的耐磨性能。这说明将热处理工艺用于烧结型金刚石工具的制造中是切实可行的。     

考虑轨道摄动的外热流计算分析

为改进传统外热流算法未考虑外热流经多次反射后的吸收和国外商业软件未考虑轨道摄动及太阳矢量变化对外热流的影响等不足,重新定义了外热流角系数和外热流辐射传递因子,综合SGP4轨道模型和Gebhart方法,给出了考虑摄动等因素的辐射传递因子和轨道外热流计算模型,以及相应的计算流程。通过仿真分析论证了考虑多次反射及摄动等因素的重要性。     

Experimental investigation and correlation development of jet impingement heat transfer with two rows of aligned jet holes on an internal surface of a wing leading edge

Extensive experimental studies on the heat transfer characteristics of two rows of aligned jet holes impinging on a concave surface in a wing leading edge were conducted, where50000 Rej 90000, 1.74 H/d 27.5, 66° a 90°, and 13.2 r/d 42.03. The finding was that the heat transfer performance at the jet-impingement stagnation point with two rows of aligned jet holes was the same as that with a single row of jet holes or the middle row of three-row configurations when the circumferential angle of the two jet holes was larger than 30°. The attenuation coefficient distribution of the jet impingement heat transfer in the chordwise direction was so complicated that two zones were divided for a better analysis. It indicated that: the attenuation coefficient curve in the jet impingement zone exhibited an approximate upside-down bell shape with double peaks and a single valley; the attenuation coefficient curve in the non-jet impingement zone was like a half-bell shape, which was similar to that with three rows of aligned jet holes; the factors,including Rej, H/d and r/d, affected the attenuation coefficient value at the valley significantly.When r/d was increased from 30.75 to 42.03, the attenuation rates of attenuation coefficient increased only by 1.8%. Consequently, experimental data-based correlation equations of the Nusselt number for the heat transfer at the jet-impingement stagnation point and the distributionof the attenuation coefficient in the chordwise direction were acquired, which play an important role in designing the wing leading edge anti-icing system with two rows of aligned jet holes.     

Aerothermodynamic and stability analyses of a deployable re-entry capsule

Recent research projects, in the field of atmospheric re-entry technology, are focused on the design of deployable, umbrella-like Thermal Protection Systems (TPSs). These TPSs are made of flexible high temperature resistant fabrics, folded at launch and deployed in space for de-orbit and re-entry operations. In the present paper two possible sphere–cone configurations for the TPS have been investigated from an aerodynamic point of view. The analyzed configurations are characterized by the same reentry mass and maximum diameter, but have different half-cone angles (45° and 60°). The analyses involve both the evaluation of thermal and aerodynamic loads and the assessment of the capsule longitudinal stability. The aerothermodynamic analysis has been performed for the completely deployed heat shield in transitional and continuum regimes, while the longitudinal stability has been analyzed in free molecular, transitional and continuum regimes, also taking into consideration the heat shield deployment sequence at high altitudes.     

改进的电热除冰系统的仿真方法

建立了电热除冰系统矩形微段的二维简化物理模型，采用焓法模型建立相变导热问题的微分控制方程，用控制容积法对该模型的控制方程及其边界、初始条件进行离散，使用块修正技术对原有的离散方程组的求解方法进行了改进，得到各个时刻的温度分布及冰的融解情况。计算结果与国外文献结果吻合，验证了改进的算法和程序的正确性。并计算分析了时间步长的选择、网格的划分对计算结果的影响。