基于Kalman滤波的GPS/INS接收机自适应干扰抑制方法

 考虑到惯导信息辅助GPS(GPS/INS)接收机对干扰抑制实时性的要求,提出一种基于Kalman滤波的GPS/INS接收机自适应干扰抑制方法。自适应广义旁瓣相消(GSC)多采用低复杂度最小均方(LMS)算法更新权矢量,收敛速率较低,严重时会导致接收机定位中断。首先利用Householder变换构建GSC下支路的阻塞矩阵,用于阻塞任意二维阵型阵列接收的期望信号;再用Kalman滤波自适应更新下支路权矢量,从而有效提高阵列输出信干噪比(SINR)。理论分析和仿真结果说明本文方法可有效抑制干扰对接收机的影响,且具有实时性高的特点。     

LF算法中蚁群移动策略的研究

采用FM、误分类错误率和运行时间作为衡量改进的LF算法的评价指标,对算法中蚁群的不同移动策略进行研究.这些移动策略包括完全随机移动、局部记忆指导下的直接跳转、局部记忆指导下的定向随机靠近、全局记忆指导下的直接跳转、全局记忆指导下定向随机靠近和局部记忆与全局记忆共同指导下的定向随机靠近6种移动策略.针对每种策略,固定算法的其他运行参数,在UCI数据集的Iris数据和Wine数据上运行的结果表明,全局记忆指导下的定向随机靠近策略运行效果最好,而且收敛速度快,并能有效避免局部最优化的问题.     

Environmental stress level evaluation approach based on physical model and interval grey association degree

 Associating environmental stresses (ESs) with built-in test (BIT) output is an important means to help diagnose intermittent faults (IFs). Aiming at low efficiency in association of traditional time stress measurement device (TSMD), an association model is built. Thereafter, a novel approach is given to evaluate the integrated environmental stress (IES) level. Firstly, the selection principle and approach of main environmental stresses (MESs) and key characteristic parameters (KCPs) are presented based on fault mode, mechanism, and ESs analysis (FMMEA). Secondly, reference stress events (RSEs) are constructed by dividing IES into three stress levels according to its impact on faults; and then the association model between integrated environmental stress event (IESE) and BIT output is built. Thirdly, an interval grey association approach to evaluate IES level is proposed due to the interval number of IES value. Consequently, the association output can be obtained as well. Finally, a case study is presented to demonstrate the proposed approach. Results show the proposed model and approach are effective and feasible. This approach can be used to guide ESs measure, record, and association. It is well suited for on-line assistant diagnosis of faults, especially IFs.     

薄壳机匣开孔补强的应力集中分析

发动机机匣上安装凸台结构，可简化为机匣壳体开孔后用围壁和加强板组合补强的力学模型。文中从弹性力学的基本公式出发，采用上述简化模型，得到了壳体孔边应力分析的计算公式，并编制了计算程序，进行了实例计算，获得了发动机机匣各种安装凸台的应力集中系数。本文的研究成果对合理地确定机匣安装凸台的几何形状和尺寸具有参考价值。     

Experimental investigation on deformation behavior of TJ-1 lunar soil simulant subjected to principal stress rotation

The knowledge of mechanical properties of lunar soil is of fundamental importance for the coming exploration of the Moon. This paper aims to investigate the fundamental deformation behavior of lunar soil and the effects of the intermediate principal stress coefficient, deviatoric stress ratio, and mean stress during the principal stress rotation. First, an improved technique was proposed to generate homogeneous samples based on the Multi-layer Undercompaction Method. Second, three series of tests on TJ-1 lunar soil simulant under the principal stress rotation were performed with a hollow cylinder apparatus at Tongji University, China. In each series of tests, only one value of the three variables mentioned above was changed while the others were kept constant. The test results demonstrate that the rotation of principal stress can result in significant plastic deformation, volumetric strain, and non-coaxiality (non-coincidence of the increment direction of principal plastic strain with the principal stress direction) of TJ-1 lunar soil simulant. In addition, it is found that the intermediate principal stress coefficient, deviatoric stress ratio, and mean stress have different influences on the four strain components, i.e. _εz,_εr,_εθ${\epsilon }_z\text{,}{\epsilon }_{\text{r}}\text{,}{\epsilon }_{\theta }$ and _γzθ${\gamma }_{z\theta }$, volumetric strain, and non-coaxiality during the principal stress rotation. The influence of deviatoric stress ratio is relatively stronger than the others. Therefore, the influence of principal stress rotation on the deformation behavior of lunar soil should be taken into account carefully in the design and construction of facilities on the lunar surface in the future.     

多层波纹管焊接接头设计与焊接工艺研究

介绍了多层波纹管焊接接头结构形式,分析了多层波纹管的焊接工艺性及工艺难点。采用滚焊+熔焊的焊接工艺,解决了焊接后焊缝气孔缺陷、熔深浅的问题。改进后的批产试验件焊缝一次交检全部达到I级标准,并通过地面单元试验考核。     

液体火箭发动机模块化通用仿真

以大型液体火箭发动机研制为背景,根据模块化建模思想和通用仿真要求,提出一种具有良好通用性和系统组织能力的仿真方法,数学模型在模块内的存储形式是代码文本,操作者只需从界面即可添加模型,扩展模块库.描述了实现这种方法的软件架构,在Microsoft Visual Studio 6.0平台上,采用C++语言开发出该仿真软件,...     

一种凹多边形凸分解的全局剖分算法

提出了一种凹多边形凸分解的全局剖分算法。首先对局部剖分算法的原理及存在的问题进行了阐述,并对基于正负法搜索可视点串的算法进行了更正和改进,然后利用改进的权函数从全局剖分的角度选择最优的剖分点进行剖分。同局部剖分算法相比,提高了剖分后所得的多边形形态质量。该算法主要作为轮廓偏置算法的前期处理算法,对原轮廓进行分解,提高了原轮廓多边形进行轮廓偏置算法的运行效率。     

高风险场所安全防范系统不确定性分析与评估

安全防范系统运行的有效性是保证被防护对象的关键。然而,安全防范系统本身及其运行环境存在多种不确定性因素,这些不确定性的存在将导致场所内存在很大的风险性,如果分析处理不当会产生严重的后果。在给出物理系统不确定性模型的基础上,分析了安全防范系统中存在的不确定性因素,提出了层次分析和灰色理论相结合的方法,评估不确定风险因素的权重,实现对入侵报警系统不确定性的评估。     

工艺方法对某结构形式的强度影响研究

以某结构形式为例,研究了加工工艺对其强度、尤其是疲劳强度的影响,讨论了产生裂纹的原因,提出了工艺改进措施并得到了试验验证。结果表明,结构根部的应力集中是疲劳强度降低并出现裂纹的原因,加工工艺对疲劳强度有较大影响,改进工艺后,该结构根部应力集中程度降低,抗疲劳性能明显改善。