规则回转体自动铺丝轨迹规划与丝束增减

为满足自动铺丝轨迹的满铺覆性要求，针对现阶段自动铺丝轨迹规划存在的不足，提出了不同的丝束增减算法。首先讨论纤维铺放方向的确定和中心轨迹数量的计算，设计不同铺放方向轨迹的生成算法。然后以丝束重叠系数为重要参数，对于纤维局部堆积和空缺问题提出单侧纤维裁剪算法和双侧纤维裁剪算法，并对裁剪后的重叠区域和间隙区域进行面积求解，使得纤维丝束均匀覆于芯模表面。最后基于CATIA CAA二次开发平台，将上述算法集成到纤维铺放CAD系统中，通过运动仿真系统验证算法的正确性。利用提出的丝束增减算法，实现了间隙/重叠区的均匀分布，尽量降低了富树脂区等相关缺陷的聚集对性能的不良影响。     

导引头量测故障下的增量式三维制导律设计

考虑导引头量测故障下拦截机动目标的末制导问题,以提高制导系统的鲁棒性、降低制导增益、减小系统残差、避免视线角速率剧烈振荡/发散为目的,基于增量式控制方法设计了一种具有鲁棒增强特性的三维末制导律。首先,将末制导问题转化为零化视线角速率的控制问题。其次,通过弹目相对距离及视线角速率定义辅助变量,给出传统的滑模制导律作为设计参考。然后,基于增量式非线性动态逆滑模控制方法,充分挖掘视线角加速度估计信息及上一采样时刻的制导指令,得到增量式三维鲁棒制导律。最后,在目标机动及导引头量测故障下,分析并比较了两种制导律所产生的系统残差。理论分析及多工况仿真结果表明,增量式制导律不仅对目标机动及大范围失效的导引头量测故障具有强鲁棒性,而且所需制导增益也较小,同时避免了末端视线角速率严重发散的问题     

A discrete event systems approach to discriminating intermittent from permanent faults

Almost all work on model-based diagnosis （MBD） potentially presumes faults are per- sistent and does not take intermittent faults （IFs） into account. Therefore, it is common for diag- nosis systems to misjudge IFs as permanent faults （PFs）, which are the major cause of the problems of false alarms, cannot duplication and no fault found in aircraft avionics. To address this problem, a new fault model which includes PFs and IFs is presented based on discrete event systems （DESs）. Thereafter, an approach is given to discriminate between PFs and IFs by diagnosing the current fault. In this paper, the regulations of （PFs and IFs） fault evolution through fault and reset events along the traces of system are studied, and then label propagation function is modified to account for PFs and the dynamic behavior of IFs and diagnosability of PFs and IFs are defined. Finally, illustrative examples are presented to demonstrate the proposed approach, and the analysis results show the fault types can be discriminated within bounded delay if the system is diagnosable.     

Investigations into sensing characteristics of circular thin-plate electrostatic sensors for gas path monitoring

Circular thin-plate electrostatic sensors are promising in gas path monitoring due to their advantages of non-intrusiveness and easy installation. The spatial sensitivity and filtering effect are two important performance parameters. In this paper, an analytically mathematical model of induced charge on a circular thin-plate electrode is first derived. Then the spatial sensitivity and filtering effect of the circular electrostatic sensor are investigated by numerical calculations. Finally,experimental studies are performed to testify the theoretical results. Both theoretical and experimental results demonstrate that circular thin-plate electrostatic sensors act as a low-pass filter in the spatial frequency domain, and both the spatial filtering effect and the temporal frequency response characteristics depend strongly on the spatial position and velocity of the charged particle. These conclusions can provide guidelines for the optimal design of circular thin-plate electrostatic sensors.     

V2500型发动机排气温度显示偏高分析及解决方案研究

V2500型发动机排气温度（EGT）指示偏高问题经常导致航班延误甚至飞机返航。本文研究了V2500型发动机排气温度显示偏高问题的原因，并提出了解决方案。     

推力室逆置点火瞬时真空舱流场数值与试验研究

针对高空模拟舱内逆向布置的推力室点火瞬时过程中舱内压力的变化规律进行了理论和数值仿真分析,推力室高速气流的动能是推力室短程点火过程中舱内压力大幅上升的主要原因.为保证推力室点火时舱内的真空度,需要在推力室出口配置导流装置将燃气导出真空舱.对单台和4台并联推力室进行点火试验,试验表明：采用燃气导流能够较好保持舱内真空度,是整机多推力室高空模拟试验的新思路.     

油液含气量对液压系统的影响

飞机液压系统油液的含气量，空气进入飞机液压系统的形式以及飞机液压系统油液中的空气对飞机液压系统的影响，慢慢被国内外从事液压系统研制人们所重视，在国内，一些大专院校和液压技术研究机构正着手研究液压系统中这些问题。一个好的液压系统，它的抗故障能力是较强的，但是，设计中忽视某些问题，则容易产生这样、那样的故障，甚至使液压系统造成灾难性后果，应引起我们重视。     

ZnCr2O4-V2O5-Li2O-ZnO湿敏材料的气体选择性研究

测试了ZnCr2O4-V2O5-Li2O-ZnO感湿体在H2、CO2、煤气、酒精蒸汽等气体环境中电阻的变化情况.结果表明,电阻值明显随环境温度变化但基本不受气体影响.     

The structure and effects of cooling flows in clusters of galaxies

Rapidly cooling gas is commonly found near the centres of clusters of galaxies. The structure of the resulting gas flows is reviewed. Total gas cooling rates of several hundred M yr⁻¹ have been observed in a number of cases. Thermal instability and the ultimate fate of the cooled gas are discussed. The cooled gas could easily have formed a massive central galaxy.     

Cutting path-dependent machinability of SiCp/Al composite under multi-step ultra-precision diamond cutting

Particle-tool interactions, which govern the synergetic deformation of SiC particle reinforced Al matrix composites under mechanical machining, strongly depend on the geometry of particle position residing on cutting path. In the present work, we investigate the influence of cutting path on the machinability of a SiCp/Al composite in multi-step ultra-precision diamond cutting by combining finite element simulations with experimental observations and characterization. Be consistent with experimentally characterized microstructures, the simulated SiCp/Al composite is considered to be composed of randomly distributed polygonally-shaped SiC particles with a volume fraction of 25vol%. A multi-step cutting strategy with depths of cut ranging from 2 to 10 μm is adopted to achieve an ultimate depth of cut of 10 μm. Intrinsic material parameters and extrinsic cutting conditions utilized in finite element simulations of SiCp/Al cutting are consistent with those used in corresponding experiments. Simulation results reveal different particle-tool interactions and failure modes of SiC particles, as well as their correlations with machining force evolution, residual stress distribution and machined surface topography. A detailed comparison between numerical simulation results and experimental data of multi-step diamond cutting of SiCp/Al composite reveals a substantial impact of the number of cutting steps on particle-tool interactions and machined surface quality. These findings provide guidelines for achieving high surface finish of SiCp/Al composites by ultra-precision diamond cutting.